Use uint64_t instead of u64 in put_dec()

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 766e9e0ebd88f05741ea6cf34657ace277dd75d6..7663f7a8c55ca5b712b7333655badf8e528e76df 100644 (file)
--- a/README
+++ b/README
@@ -538,6 +538,18 @@ The following options need to be configured:
                interleaving mode, handled by Dickens for Freescale layerscape
                SoCs with ARM core.
 
+               CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
+               Number of controllers used as main memory.
+
+               CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+               Number of controllers used for other than main memory.
+
+               CONFIG_SYS_FSL_SEC_BE
+               Defines the SEC controller register space as Big Endian
+
+               CONFIG_SYS_FSL_SEC_LE
+               Defines the SEC controller register space as Little Endian
+
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
@@ -611,13 +623,6 @@ The following options need to be configured:
                exists, unlike the similar options in the Linux kernel. Do not
                set these options unless they apply!
 
-- CPU timer options:
-               CONFIG_SYS_HZ
-
-               The frequency of the timer returned by get_timer().
-               get_timer() must operate in milliseconds and this CONFIG
-               option must be set to 1000.
-
 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 
@@ -1453,6 +1458,9 @@ The following options need to be configured:
                CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
                txfilltuning field in the EHCI controller on reset.
 
+               CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
+               HW module registers.
+
 - USB Device:
                Define the below if you wish to use the USB console.
                Once firmware is rebuilt from a serial console issue the
@@ -2710,6 +2718,14 @@ CBFS (Coreboot Filesystem) support
                200 ms.
 
 - Configuration Management:
+               CONFIG_BUILD_TARGET
+
+               Some SoCs need special image types (e.g. U-Boot binary
+               with a special header) as build targets. By defining
+               CONFIG_BUILD_TARGET in the SoC / board header, this
+               special image will be automatically built upon calling
+               make / MAKEALL.
+
                CONFIG_IDENT_STRING
 
                If defined, this string will be added to the U-Boot
@@ -2818,10 +2834,6 @@ CBFS (Coreboot Filesystem) support
 
                Enable auto completion of commands using TAB.
 
-               Note that this feature has NOT been implemented yet
-               for the "hush" shell.
-
-
                CONFIG_SYS_HUSH_PARSER
 
                Define this variable to enable the "hush" shell (from
@@ -4042,6 +4054,11 @@ Configuration Settings:
        be asserted. See doc/README.omap-reset-time for details on how
        the value can be calulated on a given board.
 
+- CONFIG_USE_STDINT
+       If stdint.h is available with your toolchain you can define this
+       option to enable it. You can provide option 'USE_STDINT=1' when
+       building U-Boot to enable this.
+
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations: