default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
---help---
Set the dram clock speed, valid range 240 - 480, must be a multiple
- of 24. Note on sun4i / sun5i / sun7i this is only used by boards
- which use dram autoconfig.
+ of 24.
+
+if MACH_SUN5I || MACH_SUN7I
+config DRAM_MBUS_CLK
+ int "sunxi mbus clock speed"
+ default 300
+ ---help---
+ Set the mbus clock speed. The maximum on sun5i hardware is 300MHz.
+
+endif
config DRAM_ZQ
int "sunxi dram zq value"
default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
default 127 if MACH_SUN7I
---help---
- Set the dram zq value. Note on sun4i / sun5i / sun7i this is only
- used by boards which use dram autoconfig.
+ Set the dram zq value.
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
default 0 if MACH_SUN4I
default 4 if MACH_SUN5I || MACH_SUN7I
---help---
- Set the dram controller emr1 value. Note this is only used by boards
- which use dram autoconfig.
-endif
-
-config SYS_CONFIG_NAME
- default "sun4i" if MACH_SUN4I
- default "sun5i" if MACH_SUN5I
- default "sun6i" if MACH_SUN6I
- default "sun7i" if MACH_SUN7I
- default "sun8i" if MACH_SUN8I
-
-choice
- prompt "Board"
-
-config TARGET_A10S_OLINUXINO_M
- bool "A10S_OLINUXINO_M"
- depends on MACH_SUN5I
-
-config TARGET_A13_OLINUXINOM
- bool "A13_OLINUXINOM"
- depends on MACH_SUN5I
-
-config TARGET_A13_OLINUXINO
- bool "A13_OLINUXINO"
- depends on MACH_SUN5I
+ Set the dram controller emr1 value.
-config TARGET_A20_OLINUXINO_L2
- bool "A20_OLINUXINO_L2"
- depends on MACH_SUN7I
-
-config TARGET_A20_OLINUXINO_L
- bool "A20_OLINUXINO_L"
- depends on MACH_SUN7I
-
-config TARGET_A20_OLINUXINO_M
- bool "A20_OLINUXINO_M"
- depends on MACH_SUN7I
-
-config TARGET_AUXTEK_T004
- bool "AUXTEK_T004"
- depends on MACH_SUN5I
-
-config TARGET_BANANAPI
- bool "BANANAPI"
- depends on MACH_SUN7I
-
-config TARGET_BANANAPRO
- bool "BANANAPRO"
- depends on MACH_SUN7I
-
-config TARGET_CUBIEBOARD2
- bool "CUBIEBOARD2"
- depends on MACH_SUN7I
-
-config TARGET_CUBIETRUCK
- bool "CUBIETRUCK"
- depends on MACH_SUN7I
+config DRAM_ODT_EN
+ int "sunxi dram odt_en value"
+ default 0
+ ---help---
+ Set the dram controller odt_en parameter. This can be used to
+ enable/disable the ODT feature.
-config TARGET_PCDUINO3
- bool "PCDUINO3"
- depends on MACH_SUN7I
+config DRAM_TPR3
+ hex "sunxi dram tpr3 value"
+ default 0
+ ---help---
+ Set the dram controller tpr3 parameter. This parameter configures
+ the delay on the command lane and also phase shifts, which are
+ applied for sampling incoming read data. The default value 0
+ means that no phase/delay adjustments are necessary. Properly
+ configuring this parameter increases reliability at high DRAM
+ clock speeds.
+
+config DRAM_DQS_GATING_DELAY
+ hex "sunxi dram dqs_gating_delay value"
+ default 0
+ ---help---
+ Set the dram controller dqs_gating_delay parmeter. Each byte
+ encodes the DQS gating delay for each byte lane. The delay
+ granularity is 1/4 cycle. For example, the value 0x05060606
+ means that the delay is 5 quarter-cycles for one lane (1.25
+ cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes.
+ The default value 0 means autodetection. The results of hardware
+ autodetection are not very reliable and depend on the chip
+ temperature (sometimes producing different results on cold start
+ and warm reboot). But the accuracy of hardware autodetection
+ is usually good enough, unless running at really high DRAM
+ clocks speeds (up to 600MHz). If unsure, keep as 0.
-config TARGET_MELE_M3
- bool "MELE_M3"
- depends on MACH_SUN7I
+choice
+ prompt "sunxi dram timings"
+ default DRAM_TIMINGS_VENDOR_MAGIC
+ ---help---
+ Select the timings of the DDR3 chips.
-config TARGET_MK802_A10S
- bool "MK802_A10S"
- depends on MACH_SUN5I
+config DRAM_TIMINGS_VENDOR_MAGIC
+ bool "Magic vendor timings from Android"
+ ---help---
+ The same DRAM timings as in the Allwinner boot0 bootloader.
-config TARGET_MSI_PRIMO73
- bool "MSI Primo73 (7\" tablet)"
- depends on MACH_SUN7I
+config DRAM_TIMINGS_DDR3_1066F_1333H
+ bool "JEDEC DDR3-1333H with down binning to DDR3-1066F"
+ ---help---
+ Use the timings of the standard JEDEC DDR3-1066F speed bin for
+ DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin
+ for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips
+ used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333
+ or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm
+ that down binning to DDR3-1066F is supported (because DDR3-1066F
+ uses a bit faster timings than DDR3-1333H).
+
+config DRAM_TIMINGS_DDR3_800E_1066G_1333J
+ bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J"
---help---
- The MSI Primo73 is an A20 based tablet, with 1G RAM, 16G NAND,
- 1024x600 TN LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
- rear camera, 3000 mAh battery, gt911 touchscreen, mma8452 accelerometer
- and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
- (both volume buttons are also connected to the UBOOT_SEL pin). The
- external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
- OTG and 3.5mm headphone jack. More details are available at
- http://linux-sunxi.org/MSI_Primo73
+ Use the timings of the slowest possible JEDEC speed bin for the
+ selected DRAM_CLK. Depending on the DRAM_CLK value, it may be
+ DDR3-800E, DDR3-1066G or DDR3-1333J.
-config TARGET_I12_TVBOX
- bool "I12_TVBOX"
- depends on MACH_SUN7I
+endchoice
-config TARGET_R7DONGLE
- bool "R7DONGLE"
- depends on MACH_SUN5I
+endif
-endchoice
+config SYS_CONFIG_NAME
+ default "sun4i" if MACH_SUN4I
+ default "sun5i" if MACH_SUN5I
+ default "sun6i" if MACH_SUN6I
+ default "sun7i" if MACH_SUN7I
+ default "sun8i" if MACH_SUN8I
config SYS_BOARD
default "sunxi"
bool "SPL/FEL mode support"
depends on SPL
default n
+ help
+ This enables support for Fast Early Loader (FEL) mode. This
+ allows U-Boot to be loaded to the board over USB by the on-chip
+ boot rom. U-Boot should be sent in two parts: SPL first, with
+ 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
+ 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
+ shrinks the amount of SRAM available to SPL, so only enable it if
+ you need FEL. Note that enabling this option only allows FEL to be
+ used; it is still possible to boot U-Boot from boot media. U-Boot
+ SPL detects when it is being loaded using FEL.
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
Set the Vbus enable pin for usb0 (otg). This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config USB0_VBUS_DET
+ string "Vbus detect pin for usb0 (otg)"
+ depends on USB_MUSB_SUNXI
+ default ""
+ ---help---
+ Set the Vbus detect pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
LCD interface driving a VGA connector, such as found on the
Olimex A13 boards.
+config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH
+ boolean "Force sync active high for VGA via LCD controller support"
+ depends on VIDEO_VGA_VIA_LCD
+ default n
+ ---help---
+ Say Y here if you've a board which uses opendrain drivers for the vga
+ hsync and vsync signals. Opendrain drivers cannot generate steep enough
+ positive edges for a stable video output, so on boards with opendrain
+ drivers the sync signals must always be active high.
+
config VIDEO_VGA_EXTERNAL_DAC_EN
string "LCD panel power enable pin"
depends on VIDEO_VGA_VIA_LCD
Set the power enable pin for the LCD panel. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_LCD_RESET
+ string "LCD panel reset pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the reset pin for the LCD panel. This takes a string in the format
+ understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config VIDEO_LCD_BL_EN
string "LCD panel backlight enable pin"
depends on VIDEO
---help---
Set this if the backlight pwm output is active low.
+config VIDEO_LCD_PANEL_I2C
+ bool "LCD panel needs to be configured via i2c"
+ depends on VIDEO
+ default m
+ ---help---
+ Say y here if the LCD panel needs to be configured via i2c. This
+ will add a bitbang i2c controller using gpios to talk to the LCD.
+
+config VIDEO_LCD_PANEL_I2C_SDA
+ string "LCD panel i2c interface SDA pin"
+ depends on VIDEO_LCD_PANEL_I2C
+ default "PG12"
+ ---help---
+ Set the SDA pin for the LCD i2c interface. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_PANEL_I2C_SCL
+ string "LCD panel i2c interface SCL pin"
+ depends on VIDEO_LCD_PANEL_I2C
+ default "PG10"
+ ---help---
+ Set the SCL pin for the LCD i2c interface. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
# Note only one of these may be selected at a time! But hidden choices are
# not supported by Kconfig
---help---
7.85" 1024x768 Hitachi tx18d42vm LCD panel support
+config VIDEO_LCD_TL059WV5C0
+ bool "tl059wv5c0 LCD panel"
+ select VIDEO_LCD_PANEL_I2C
+ select VIDEO_LCD_IF_PARALLEL
+ ---help---
+ 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and
+ Aigo M60/M608/M606 tablets.
+
endchoice
Say Y here to add support for using a USB keyboard (typically used
in combination with a graphical console).
+config GMAC_TX_DELAY
+ int "GMAC Transmit Clock Delay Chain"
+ default 0
+ ---help---
+ Set the GMAC Transmit Clock Delay Chain value.
+
endif
projects / karo-tx-uboot.git / blobdiff