#include <i2c.h>
#include <asm/byteorder.h>
-#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
/* Display values from last command.
* The SDRAM command is separately configured because many
* (most?) embedded boards don't use SDRAM DIMMs.
*/
-#if (CONFIG_COMMANDS & CFG_CMD_SDRAM)
+#if defined(CONFIG_CMD_SDRAM)
/*
* Syntax:
switch(data[2]) {
case 2: puts ("EDO\n"); break;
case 4: puts ("SDRAM\n"); break;
+ case 8: puts ("DDR2\n"); break;
default: puts ("unknown\n"); break;
}
puts ("Row address bits ");
case 2: puts ("HSTL 1.5\n"); break;
case 3: puts ("SSTL 3.3\n"); break;
case 4: puts ("SSTL 2.5\n"); break;
+ case 5: puts ("SSTL 1.8\n"); break;
default: puts ("unknown\n"); break;
}
printf("SDRAM cycle time %d.%d nS\n",
return 0;
}
-#endif /* CFG_CMD_SDRAM */
+#endif
#if defined(CONFIG_I2C_CMD_TREE)
#if defined(CONFIG_I2C_MULTI_BUS)
return do_i2c_probe(cmdtp, flag, --argc, ++argv);
if (!strncmp(argv[1], "lo", 2))
return do_i2c_loop(cmdtp, flag, --argc, ++argv);
-#if (CONFIG_COMMANDS & CFG_CMD_SDRAM)
+#if defined(CONFIG_CMD_SDRAM)
if (!strncmp(argv[1], "sd", 2))
return do_sdram(cmdtp, flag, --argc, ++argv);
-#endif /* CFG_CMD_SDRAM */
+#endif
else
printf ("Usage:\n%s\n", cmdtp->usage);
return 0;
/***************************************************/
+#if defined(CONFIG_I2C_CMD_TREE)
+U_BOOT_CMD(
+ i2c, 6, 1, do_i2c,
+ "i2c - I2C sub-system\n",
+#if defined(CONFIG_I2C_MULTI_BUS)
+ "dev [dev] - show or set current I2C bus\n"
+#endif /* CONFIG_I2C_MULTI_BUS */
+ "i2c speed [speed] - show or set I2C bus speed\n"
+ "i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device\n"
+ "i2c mm chip address[.0, .1, .2] - write to I2C device (auto-incrementing)\n"
+ "i2c mw chip address[.0, .1, .2] value [count] - write to I2C device (fill)\n"
+ "i2c nm chip address[.0, .1, .2] - write to I2C device (constant address)\n"
+ "i2c crc32 chip address[.0, .1, .2] count - compute CRC32 checksum\n"
+ "i2c probe - show devices on the I2C bus\n"
+ "i2c loop chip address[.0, .1, .2] [# of objects] - looping read of device\n"
+#if defined(CONFIG_CMD_SDRAM)
+ "i2c sdram chip - print SDRAM configuration information\n"
+#endif
+);
+#endif /* CONFIG_I2C_CMD_TREE */
U_BOOT_CMD(
imd, 4, 1, do_i2c_md, \
"imd - i2c memory display\n", \
" - loop, reading a set of addresses\n"
);
-#if (CONFIG_COMMANDS & CFG_CMD_SDRAM)
+#if defined(CONFIG_CMD_SDRAM)
U_BOOT_CMD(
isdram, 2, 1, do_sdram,
"isdram - print SDRAM configuration information\n",
);
#endif
-#if defined(CONFIG_I2C_CMD_TREE)
-U_BOOT_CMD(
- i2c, 6, 1, do_i2c,
- "i2c - I2C sub-system\n",
-#if defined(CONFIG_I2C_MULTI_BUS)
- "dev [dev] - show or set current I2C bus\n"
-#endif /* CONFIG_I2C_MULTI_BUS */
- "i2c speed [speed] - show or set I2C bus speed\n"
- "i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device\n"
- "i2c mm chip address[.0, .1, .2] - write to I2C device (auto-incrementing)\n"
- "i2c mw chip address[.0, .1, .2] value [count] - write to I2C device (fill)\n"
- "i2c nm chip address[.0, .1, .2] - write to I2C device (constant address)\n"
- "i2c crc32 chip address[.0, .1, .2] count - compute CRC32 checksum\n"
- "i2c probe - show devices on the I2C bus\n"
- "i2c loop chip address[.0, .1, .2] [# of objects] - looping read of device\n"
-#if (CONFIG_COMMANDS & CFG_CMD_SDRAM)
- "i2c sdram chip - print SDRAM configuration information\n"
-#endif /* CFG_CMD_SDRAM */
-);
-#endif /* CONFIG_I2C_CMD_TREE */
-
-#endif /* CFG_CMD_I2C */
+#endif