/*
- * Copyright (C) 2009 Freescale Semiconductor, Inc.
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#define CONFIG_SYS_CLK_FREQ 66666666
#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
+#ifdef CONFIG_ATM
+#define CONFIG_PQ_MDS_PIB
+#define CONFIG_PQ_MDS_PIB_ATM
+#endif
+
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_U_BOOT 1
+#define CONFIG_RAMBOOT_NAND 1
+#define CONFIG_SYS_TEXT_BASE 0xf8f82000
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#endif
+
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R 1
#define CONFIG_HWCONFIG
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
+/*
+ * Config the L2 Cache as L2 SRAM
+ */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_L2_SIZE (512 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
/* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
/* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
+#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSRBAR_DEFAULT CONFIG_SYS_CCSRBAR
+#else
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#endif
/* DDR Setup */
#define CONFIG_FSL_DDR3
#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
/*Chip select 0 - Flash*/
-#define CONFIG_SYS_BR0_PRELIM 0xfe000801
-#define CONFIG_SYS_OR0_PRELIM 0xfe000ff7
+#define CONFIG_FLASH_BR_PRELIM 0xfe000801
+#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7
/*Chip select 1 - BCSR*/
#define CONFIG_SYS_BR1_PRELIM 0xf8000801
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
/* Chip select 3 - NAND */
+#ifndef CONFIG_NAND_SPL
#define CONFIG_SYS_NAND_BASE 0xFC000000
+#else
+#define CONFIG_SYS_NAND_BASE 0xFFF00000
+#endif
+
+/* NAND boot: 4K NAND loader config */
+#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
+#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
+#define CONFIG_SYS_NAND_U_BOOT_START \
+ (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
+
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
| OR_FCM_SCY_1 \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
+
+#ifdef CONFIG_RAMBOOT_NAND
+#define CONFIG_SYS_BR0_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR3_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR3_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
+#else
+#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
#define CONFIG_SYS_BR3_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR3_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#endif
/*
* SDRAM on the LocalBus
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SERIAL_MULTI 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "FSL UEC0"
+#define CONFIG_ETHPRIME "UEC0"
#define CONFIG_PHY_MODE_NEED_CHANGE
#define CONFIG_UEC_ETH1 /* GETH1 */
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12
#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
#elif defined(CONFIG_SYS_UCC_RMII_MODE)
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */
#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */
-#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
#endif /* CONFIG_SYS_UCC_RGMII_MODE */
#endif /* CONFIG_UEC_ETH1 */
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK17
#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
#elif defined(CONFIG_SYS_UCC_RMII_MODE)
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */
#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */
-#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_100_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
#endif /* CONFIG_SYS_UCC_RGMII_MODE */
#endif /* CONFIG_UEC_ETH2 */
#define CONFIG_SYS_UEC3_TX_CLK QE_CLK12
#define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC3_PHY_ADDR 2
-#define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC3_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
#elif defined(CONFIG_SYS_UCC_RMII_MODE)
#define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */
#define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */
-#define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_100_RMII
+#define CONFIG_SYS_UEC3_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
#endif /* CONFIG_SYS_UCC_RGMII_MODE */
#endif /* CONFIG_UEC_ETH3 */
#define CONFIG_SYS_UEC4_TX_CLK QE_CLK17
#define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC4_PHY_ADDR 3
-#define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC4_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
#elif defined(CONFIG_SYS_UCC_RMII_MODE)
#define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */
#define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */
-#define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_100_RMII
+#define CONFIG_SYS_UEC4_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
#endif /* CONFIG_SYS_UCC_RGMII_MODE */
#endif /* CONFIG_UEC_ETH4 */
#define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE
#define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC6_PHY_ADDR 4
-#define CONFIG_SYS_UEC6_INTERFACE_MODE ENET_1000_SGMII
+#define CONFIG_SYS_UEC6_INTERFACE_TYPE SGMII
+#define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
#endif /* CONFIG_UEC_ETH6 */
#undef CONFIG_UEC_ETH8 /* GETH8 */
#define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE
#define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC8_PHY_ADDR 6
-#define CONFIG_SYS_UEC8_INTERFACE_MODE ENET_1000_SGMII
+#define CONFIG_SYS_UEC8_INTERFACE_TYPE SGMII
+#define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
#endif /* CONFIG_UEC_ETH8 */
#endif /* CONFIG_QE */
/*
* Environment
*/
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#endif
+#else
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
+#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
/* Initial Memory map for Linux*/
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
projects / karo-tx-uboot.git / blobdiff