Enable POST memory test for P2020DS

[karo-tx-uboot.git] / include / configs / da850evm.h

diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h
index 016a21e9d0bdb62ae7df20e4a8c5a3756899b706..7bf6336b1312544958874f6dd37395fd5992b853 100644 (file)
--- a/include/configs/da850evm.h
+++ b/include/configs/da850evm.h
@@ -26,6 +26,7 @@
 /*
  * Board
  */
+#define CONFIG_DRIVER_TI_EMAC
 
 /*
  * SoC Configuration
@@ -47,6 +48,7 @@
 #define CONFIG_SYS_GBL_DATA_SIZE       128 /* reserved for initial data */
 #define PHYS_SDRAM_1           DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
 #define PHYS_SDRAM_1_SIZE      (64 << 20) /* SDRAM size 64MB */
+#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
 
 /* memtest start addr */
 #define CONFIG_SYS_MEMTEST_START       (PHYS_SDRAM_1 + 0x2000000)
@@ -77,6 +79,43 @@
 #define CONFIG_SYS_I2C_SPEED           25000
 #define CONFIG_SYS_I2C_SLAVE           10 /* Bogus, master-only in U-Boot */
 
+/*
+ * Flash & Environment
+ */
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_IN_NAND          /* U-Boot env in NAND Flash  */
+#define CONFIG_ENV_OFFSET              0x0 /* Block 0--not used by bootcode */
+#define CONFIG_ENV_SIZE                        (128 << 10)
+#define        CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define        CONFIG_SYS_NAND_PAGE_2K
+#define CONFIG_SYS_NAND_CS             3
+#define CONFIG_SYS_NAND_BASE           DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
+#define CONFIG_SYS_CLE_MASK            0x10
+#define CONFIG_SYS_ALE_MASK            0x8
+#undef CONFIG_SYS_NAND_HW_ECC
+#define CONFIG_SYS_MAX_NAND_DEVICE     1 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS                 1
+#define DEF_BOOTM                      ""
+#endif
+
+/*
+ * Network & Ethernet Configuration
+ */
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM       0
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_NET_MULTI
+#endif
+
 /*
  * U-Boot general configuration
  */
@@ -99,7 +138,7 @@
 /*
  * Linux Information
  */
-#define LINUX_BOOT_PARAM_ADDR  (CONFIG_SYS_MEMTEST_START + 0x100)
+#define LINUX_BOOT_PARAM_ADDR  (PHYS_SDRAM_1 + 0x100)
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTARGS                \
@@ -126,6 +165,20 @@
 #undef CONFIG_CMD_PING
 #endif
 
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_NAND
+
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_LZO
+#define CONFIG_RBTREE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#endif
+
 #if !defined(CONFIG_USE_NAND) && \
        !defined(CONFIG_USE_NOR) && \
        !defined(CONFIG_USE_SPIFLASH)
@@ -137,7 +190,6 @@
 #endif
 
 /* additions for new relocation code, must added to all boards */
-#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */
 #define CONFIG_SYS_SDRAM_BASE          0xc0000000
 #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
                                        CONFIG_SYS_GBL_DATA_SIZE)