/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128 * 1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
#define CONFIG_HARD_I2C 1
#define CONFIG_I2C_MXC 1
-#define CFG_I2C_MX31_PORT2 1
-#define CFG_I2C_SPEED 100000
-#define CFG_I2C_SLAVE 0xfe
+#define CONFIG_SYS_I2C_MX31_PORT2 1
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0xfe
-#define CONFIG_MX31_UART 1
-#define CFG_MX31_UART1 1
+#define CONFIG_MXC_UART 1
+#define CONFIG_SYS_MX31_UART1 1
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
"prg_jffs2=tftpboot 0x80000000 $(jffs2); erase 0xa01c0000 0xa1ffffff; cp.b 0x80000000 0xa01c0000 $(filesize)\0"
-#define CONFIG_DRIVER_SMC911X 1
-#define CONFIG_DRIVER_SMC911X_BASE 0xa8000000
-#define CONFIG_DRIVER_SMC911X_32_BIT 1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X 1
+#define CONFIG_SMC911X_BASE 0xa8000000
+#define CONFIG_SMC911X_32_BIT 1
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "uboot> "
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "uboot> "
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0 /* memtest works on */
-#define CFG_MEMTEST_END 0x10000
+#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x10000
-#define CFG_LOAD_ADDR 0 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0 /* default load address */
-#define CFG_HZ 32000
+#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING 1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_FLASH_BASE 0xa0000000
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 259 /* max number of sectors on one chip */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
-
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0x00 /* environment starts here */
-#define CFG_ENV_SIZE 4096
-#define CFG_I2C_EEPROM_ADDR 0x52
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 5 bits = 32 octets */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* between stop and start */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* length of byte address */
+#define CONFIG_SYS_FLASH_BASE 0xa0000000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max number of sectors on one chip */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
+
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_OFFSET 0x00 /* environment starts here */
+#define CONFIG_ENV_SIZE 4096
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 5 bits = 32 octets */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* between stop and start */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* length of byte address */
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
-#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (100*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (100*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Write */
/*
* JFFS2 partitions
*/
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
+/* EET platform additions */
+#ifdef CONFIG_IMX31_PHYCORE_EET
+#define BOARD_LATE_INIT
+
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_HARD_SPI 1
+#define CONFIG_MXC_SPI 1
+#define CONFIG_CMD_SPI
+
+#define CONFIG_S6E63D6 1
+
+#define CONFIG_LCD 1
+#define CONFIG_VIDEO_MX3 1
+#define CONFIG_SYS_WHITE_ON_BLACK 1
+#define LCD_BPP LCD_COLOR8
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+
+#define CONFIG_SPLASH_SCREEN 1
+#define CONFIG_CMD_BMP 1
+#endif
+
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff