#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * If we are developing, we might want to start armboot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL /* undef for developing */
-
/*
* High Level Configuration Options
* (easy to change)
#define CONFIG_LART 1 /* on an LART Board */
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_DCACHE_OFF
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
-#define CS8900_BASE 0x20008300
-#define CS8900_BUS16 1
+#define CONFIG_NET_MULTI
+#define CONFIG_CS8900 /* we have a CS8900 on-board */
+#define CONFIG_CS8900_BASE 0x20008300
+#define CONFIG_CS8900_BUS16
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL3 1 /* we use SERIAL 3 on LART */
/* allow to overwrite serial and ethaddr */
#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600"
+#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600"
#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
#define CONFIG_NETMASK 255.255.0.0
#define CONFIG_IPADDR 172.22.2.131
#define CONFIG_BOOTFILE "elinos-lart"
#define CONFIG_BOOTCOMMAND "tftp; bootm"
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "LART # " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0xc0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "LART # " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0xc8000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0xc8000000 /* default load address */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x0b /* set core clock to 220 MHz */
+#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_CPUSPEED 0x0b /* set core clock to 220 MHz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00400000 /* 4 MB */
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT (31+8) /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT (31+8) /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff