sunxi: display: Add overscan correction

[karo-tx-uboot.git] / include / configs / m28evk.h

diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
index 2d9ad5f23c9c62a41db42d26f063490a7cb3e3d4..26987d258d5a618cfdeee0d7309025ff56bf6e81 100644 (file)
--- a/include/configs/m28evk.h
+++ b/include/configs/m28evk.h
@@ -8,7 +8,6 @@
 #define __CONFIGS_M28EVK_H__
 
 /* System configurations */
-#define CONFIG_MX28                            /* i.MX28 SoC */
 #define MACH_TYPE_M28EVK       3613
 #define CONFIG_MACH_TYPE       MACH_TYPE_M28EVK
 
@@ -18,7 +17,6 @@
 
 /* U-Boot Commands */
 #define CONFIG_SYS_NO_FLASH
-#include <config_cmd_default.h>
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DOS_PARTITION
 #define CONFIG_FAT_WRITE
@@ -32,6 +30,7 @@
 #define CONFIG_CMD_EXT4
 #define CONFIG_CMD_EXT4_WRITE
 #define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
 #define CONFIG_CMD_GPIO
 #define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_I2C
@@ -39,16 +38,12 @@
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_SF
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_USB
 #define        CONFIG_VIDEO
 
-#define CONFIG_REGEX                   /* Enable regular expression support */
 
 /* Memory configuration */
 #define CONFIG_NR_DRAM_BANKS           1               /* 1 bank of DRAM */
@@ -129,7 +124,6 @@
 
 /* SPI FLASH */
 #ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_STMICRO
 #define CONFIG_SF_DEFAULT_BUS          2
 #define CONFIG_SF_DEFAULT_CS           0
@@ -170,6 +164,7 @@
 #define CONFIG_EXTRA_ENV_SETTINGS                                      \
        "consdev=ttyAMA0\0"                                             \
        "baudrate=115200\0"                                             \
+       "bootscript=boot.scr\0"                                         \
        "bootdev=/dev/mmcblk0p2\0"                                      \
        "rootdev=/dev/mmcblk0p3\0"                                      \
        "netdev=eth0\0"                                                 \
@@ -236,7 +231,7 @@
        "addargs=run addcons addmtd addmisc\0"                          \
        "mmcload="                                                      \
                "mmc rescan ; "                                         \
-               "ext4load mmc 0:2 ${kernel_addr_r} ${bootfile}\0"       \
+               "load mmc 0:2 ${kernel_addr_r} ${bootfile}\0"           \
        "ubiload="                                                      \
                "ubi part UBI ; ubifsmount ubi0:rootfs ; "              \
                "ubifsload ${kernel_addr_r} /boot/${bootfile}\0"        \
@@ -280,10 +275,10 @@
        "try_bootscript="                                               \
                "mmc rescan;"                                           \
                "if test -e mmc 0:2 ${bootscript} ; then "              \
-               "if ext4load mmc 0:2 ${kernel_addr_r} ${bootscript};"   \
-               "then;"                                                 \
-                       "\techo Running bootscript...;"                 \
-                       "\tsource ${kernel_addr_r};"                    \
+               "if load mmc 0:2 ${kernel_addr_r} ${bootscript};"       \
+               "then ; "                                               \
+                       "echo Running bootscript... ; "                 \
+                       "source ${kernel_addr_r} ; "                    \
                "fi ; "                                                 \
                "fi\0"