T210: Add support for 64-bit T210-based P2571 board

[karo-tx-uboot.git] / include / configs / mx6qsabreauto.h

diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index bd0144f5cb49ae9a060a64230c93cad831e95618..1d417afdb022bd37838e468748d955716aff3fe1 100644 (file)
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -13,7 +13,9 @@
 #define CONFIG_MXC_UART_BASE   UART4_BASE
 #define CONFIG_CONSOLE_DEV             "ttymxc3"
 #define CONFIG_DEFAULT_FDT_FILE        "imx6q-sabreauto.dtb"
-#define CONFIG_MMCROOT                 "/dev/mmcblk0p2"
+#define CONFIG_DEFAULT_FDT_FILE        "imx6dl-sabreauto.dtb"
+#endif
+#define CONFIG_MMCROOT                 "/dev/mmcblk2p2"
 #define PHYS_SDRAM_SIZE                (2u * 1024 * 1024 * 1024)
 
 /* USB Configs */
@@ -28,8 +30,21 @@
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_WIDTH   { {0x30, 8}, {0x32, 8}, {0x34, 8} }
+
 #include "mx6sabre_common.h"
 
+#undef CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
+#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
 #define CONFIG_SYS_FSL_USDHC_NUM       2
 #if defined(CONFIG_ENV_IS_IN_MMC)
 #define CONFIG_SYS_MMC_ENV_DEV         0
@@ -39,9 +54,29 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED           100000
 
-#define CONFIG_OF_SEPARATE
-#define CONFIG_DEFAULT_DEVICE_TREE   imx6q-sabreauto
+/* NAND flash command */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_SYS_NAND_BASE           0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
 
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */