+* MPC5200: enable snooping of DMA transactions on XLB even if no PCI
+ is configured; othrwise DMA accesses aren't cache coherent which
+ causes for example USB to fail.
+
+* Some code cleanup
+
+* Fix dbau1x00 boards broken by dbau1550 patch
+ PLL:s were not set for boards other than 1550.
+ Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.
+ Default boot is now bootp for cards other than 1550.
+ Patch by Thomas Lange, 10 Aug 2005
+
+* Fixes common/cmd_flash.c:
+ - fix some compiler/parser error, if using m68k tool chain
+ - optical fix for protect on/off all messages, if using more
+ then one bank
+ Patch by Jens Scharsig, 28 Jul 2005
+
+* Fix Quad UART mapping on MCC200 board due to new HW revision
+
+* Fix JFFS2 support for legacy NAND driver.
+
+* Remove dependencies between DoC code and old legacy NAND driver.
+
+* Fix PM828_PCI target, for which PCI was *not* configured in.
+
+* Fix Lite5200B support: initialize SDelay register
+ See Freescale's AN3221 "MPC5200B SDRAM Initialization and
+ Configuration", 3.3.1 SDelay--MBAR + 0x0190
+
+* Changes/fixes for drivers/cfi_flash.c:
+
+ - Add Intel legacy lock/unlock support to common CFI driver
+
+ On some Intel flash's (e.g. Intel J3) legacy unlocking is
+ supported, meaning that unlocking of one sector will unlock
+ all sectors of this bank. Using this feature, unlocking
+ of all sectors upon startup (via env var "unlock=yes") will
+ get much faster.
+
+ - Fixed problem with multiple reads of envronment variable
+ "unlock" as pointed out by Reinhard Arlt & Anders Larsen.
+
+ - Removed unwanted linefeeds from "protect" command when
+ CFG_FLASH_PROTECTION is enabled.
+
+ - Changed p3p400 board to use CFG_FLASH_PROTECTION
+
+ Patch by Stefan Roese, 01 Apr 2006
+
+* Changes/fixes for drivers/cfi_flash.c:
+ - Correctly handle the cases where CFG_HZ != 1000 (several
+ XScale-based boards)
+ - Fix the timeout calculation of buffered writes (off by a
+ factor of 1000)
+ Patch by Anders Larsen, 31 Mar 2006
+
+* Updates to common PPC4xx onboard (DDR)SDRAM init code (405 and 440)
+
+ 405 SDRAM: - The SDRAM parameters can now be defined in the board
+ config file and the 405 SDRAM controller values will
+ be calculated upon bootup (see PPChameleonEVB).
+ When those settings are not defined in the board
+ config file, the register setup will be as it is now,
+ so this implementation should not break any current
+ design using this code.
+
+ Thanks to Andrea Marson from DAVE for this patch.
+
+ 440 DDR: - Added function sdram_tr1_set to auto calculate the
+ TR1 value for the DDR.
+ - Added ECC support (see p3p440).
+
+ Patch by Stefan Roese, 17 Mar 2006
+
+* Fix CONFIG_SKIP_LOWLEVEL_INIT dependency in cpu/arm920t/start.S
+ Patch by Peter Menzebach, 13 Oct 2005 [DNX#2006040142000473]
+
+* Add support for ymodem protocol download
+ Patch by Stefano Babic, 29 Mar 2006
+
+* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000
+ Merge from Markus Klotzbücher's repo, 01 Apr 2006
+
+* GCC-4.x fixes: clean up global data pointer initialization for all
+ boards
+
+* Update for Delta board:
+ - redundant NAND environment
+ - misc Monahans cleanups (remove dead code etc.)
+ - DA9030 Initialization; some minimal changes to PXA I2C driver to
+ make it work with the Monahans.
+ - Make Monahans clock frequency configurable using
+ CFG_MONAHANS_RUN_MODE_OSC_RATIO and
+ CFG_MONAHANS_TURBO_RUN_MODE_RATIO.
+ Merge from Markus Klotzbücher's repo, 25 Mar 2006
+
+* Enable Quad UART om MCC200 board.
+
+* Cleanup MCC200 board configuration; omit non-existent stuff.
+
+* Add support for MPC859/866 Rev. A.0
+
+* Add command for handling DDR ECC registers on MPC8349EE MDS board.
+
+* Fix DDR ECC bit definitions for MPC83xx.
+
+* Add initial support for MPC8349E MDS board.
+
+* Add support for ECC DDR initialization on MPC83xx.
+
+* Add DMA support for MPC83xx.
+
+* Add sync in do_reset() routine for MPC83xx after RPR register
+ was written to. It is need on some targets when BAT translation
+ is enabled.
+
+* Add bit definitions for MPC83xx DDR controller registers.
+
+* Add Dcbz(), Dcbi() and Dcbf() routines for MPC83xx.
+
+* Correct shift offsets in icache_status and dcache_status for MPC83xx.
+
+* Add support for DS1374 RTC chip.
+
+* Add support for Lite5200B board.
+ Patch by Patch by Jose Maria (Txema) Lopez, 16 Jan 2006
+
+* Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific
+ timer and cpu_reset code from cpu/$(CPU) into the new
+ cpu/$(CPU)/$(SOC) directories
+ Patch by Andreas Engel, 13 Mar 2006
+
+* Change max size of uncompressed uImage's to 8MByte and add
+ CFG_BOOTM_LEN to adjust this setting.
+
+ As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
+ uImages was restricted to 4MBytes. This default size is now
+ increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
+ in the board config file.
+
+ Patch by Stefan Roese, 13 Mar 2006
+
+* Fix problem with updated PCI code in cpu/ppc4xx/405gp_pci.c
+ Patch by Stefan Roese, 13 Mar 2006
+
+* cpu/ppc4xx/start.S : exceptions are enabled after relocation
+ Patch by Cedric Vincent, 06 Jul 2005
+
+* au1x00_eth.c: check malloc return value and abort if it failed
+ Patch by Andrew Dyer, 26 Jul 2005
+
+* Change the sequence of events in soft_i2c.c:send_ack() to keep from
+ incorrectly generating start/stop conditions on the bus.
+ Patch by Andrew Dyer, 26 Jul 2005
+
+* Fix bug in [id]cache_status commands for MPC85xx processors;
+ should look at LSB of L1CSRn registers to determine if L1 cache is
+ enabled, not the MSB.
+ Patch by Murray Jensen, 19 Jul 2005
+
+* Fix array overflow with fw_setenv on uninitialised environment
+ Patch by Murray Jensen, 15 Jul 2005
+
+* Add support for EmbeddedPlanet EP88x boards
+ Patch by Yuli Barcohen, 13 Jul 2005
+
+* Remove board specific configuration includes from the common xilinx
+ ethernet and iic adapter code.
+ Patch by Michael Libeskind, 12 Jul 2005
+
+* Add Nat Semi DP83865 PHY support to MPC85xx TSEC driver
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add (some) definitions for the MPC85xx local bus controller
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add CPM2 I/O pin functions for MPC85xx processors
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Fix compile problem
+
+* Added PCI support for MPC8349ADS board
+ Patch by Kumar Gala 11 Jan 2006
+
+* Enable address translation on MPC83xx
+ Patch by Kumar Gala, 10 Feb 2006
+
+* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx
+ Patch by Kumar Gala, 25 Jan 2006
+
+* Fixed defines for MPC83xx SICRL register to match current specs
+ Patch by Kumar Gala, 23 Jan 2006
+
+* Only disable the MPC83xx watchdog if its enabled out of reset.
+ If its disabled out of reset SW can later enable it if so desired
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow config of GPIO direction & data registers at boot on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Enable time handling on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Make System IO Config Registers board configurable on MPC83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Fixed PCI indirect config ops to handle multiple PCI controllers
+ We need to adjust the bus number we are trying to access based
+ on which PCI controller its on
+ Patch by Kumar Gala, 12 Jan 2006
+
+* Report back PCI bus when doing table based device config
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added support for PCI prefetchable region and BARs
+ If a host controller sets up a region as prefetchable and
+ a device's BAR denotes it as prefetchable, allocate the
+ BAR into the prefetch region.
+
+ If a BAR is prefetchable and no prefetchable region has
+ been setup by the controller we fall back to allocating
+ the BAR into the normally memory region.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add helper function for generic flat device tree fixups for mpc83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for passing initrd information via flat device tree
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added OF_STDOUT_PATH and OF_SOC
+
+ OF_STDOUT_PATH specifies the path to the device the kernel can use
+ for console output
+
+ OF_SOC specifies the proper name of the SOC node if one exists.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow board code to fixup the flat device tree before booting a kernel
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added CONFIG_ options for bd_t and env in flat dev tree
+
+ CONFIG_OF_HAS_BD_T will put a copy of the bd_t
+ into the resulting flat device tree.
+
+ CONFIG_OF_HAS_UBOOT_ENV will copy the environment
+ variables from u-boot into the flat device tree
+
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for the DHCP vendor optional bootfile (#67).
+ Ignores the vendor TFTP server name option (#66).
+ Patch by Murray Jensen, 30 Jun 2005
+
+* Fix a HW timing issue on 8548 CDS for eTSEC 3 in RGMII mode
+ Patch by Andy Fleming, 14 Jun 2005
+
+* Fix bad register definitions for LTX971 PHY on MPC85xx boards.
+ Patch by Gerhard Jaeger, 21 Jun 2005
+
+* Add netconsole and some more commands to RPXlite_DW board
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix bad declaration on pci_cfgfunc_nothing
+ Patch by Sam Song, 19 Jun 2005
+
+* Adjust "echo" as a default command
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix PCIDF calculation in cpu/mpc8260/speed.c for MPC8280EC
+ Patch by KokHow Teh, 16 Jun 2005
+
+* Add crc of data to jffs2 (in jffs2_1pass_build_lists()).
+ Patch by Rick Bronson, 15 Jun 2005
+
+* Coding Style cleanup
+
+* Avoid dereferencing NULL in find_cmd() if no valid commands were found
+ Patch by Andrew Dyer, 13 Jun 2005
+
+* Add ADI Blackfin support
+ - add support for Analog Devices Blackfin BF533 CPU
+ - add support for the ADI BF533 Stamp uClinux board
+ - add support for the ADI BF533 EZKit board
+ Patches by Richard Klingler, 11 Jun 2005
+
+* Add loads of ntohl() in image header handling
+ Patch by Steven Scholz, 10 Jun 2005
+
+* Switch MPC86xADS and MPC885ADS boards to use cpuclk environment
+ variable to set clock
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* RPXlite configuration fixes
+ - Use correct flash sector size
+ - Use correct memory test end address
+ - Add support for bzip2 compression
+ - Various small fixes
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Memory configuration changes for ZPC.1900 board
+ - Fix SDRAM timing on both local bus and 60x bus
+ - Add support for second flash bank (SIMM)
+ - Change boot flash base
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Add support for Adder boards with 16MB SDRAM;
+ add support for second FEC on Adder87x board.
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Fix conditional for including ks8695eth driver
+ Patch by Greg Ungerer, 04 Jun 2005
+
+* Fix Makefile: include config.mk only after CROSS_COMPILE is defined
+ Patch by Friedrich Lobenstock, 02 Jun 2005
+
+* Fix comment in common/soft_i2c.c
+ Patches by Peter Korsgaard/Tolunay Orkun, 26 May 2005
+
+* Cleanup compiler warnings.
+ Patch by Greg Ungerer, 21 May 2005
+
+* Word alignment fixes for word aligned NS16550 UART
+ Patch by Jean-Paul Saman, 01 Mar 2005
+
+ Fixes bug with UART that only supports word aligned access: removed
+ "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" some
+ (broken!) versions of GCC generate byte accesses when encountering
+ the packed attribute regardless if the struct is already correctly
+ aligned for a platform. Peripherals that can only handle word
+ aligned access won't work properly when accessed with byte access.
+ The struct NS16550 is already word aligned for REG_SIZE = 4, so
+ there is no need to packed the struct in that case.
+
+* Fix behaviour if gatewayip is not set
+ Patch by Robin Gilks, 23 Dec 2004
+
+* Fix cleanup for netstart board.
+ Remove build results from repository
+
+* Some code cleanup for GCC 4.x
+
+* Fixes to support environment in NAND flash;
+ enable NAND flash based environment for delta board.
+
+* Add support for Intel Monahans CPU on Zylonite and Delta boards
+ (This is Work in Progress!)
+
+* Add support for TQM8260-AI boards.
+
projects / karo-tx-uboot.git / blobdiff