+======================================================================
+Changes since U-Boot 1.1.4:
+======================================================================
+
+* Add Nat Semi DP83865 PHY support to MPC85xx TSEC driver
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add (some) definitions for the MPC85xx local bus controller
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add CPM2 I/O pin functions for MPC85xx processors
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Fix compile problem
+
+* Added PCI support for MPC8349ADS board
+ Patch by Kumar Gala 11 Jan 2006
+
+* Enable address translation on MPC83xx
+ Patch by Kumar Gala, 10 Feb 2006
+
+* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx
+ Patch by Kumar Gala, 25 Jan 2006
+
+* Fixed defines for MPC83xx SICRL register to match current specs
+ Patch by Kumar Gala, 23 Jan 2006
+
+* Only disable the MPC83xx watchdog if its enabled out of reset.
+ If its disabled out of reset SW can later enable it if so desired
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow config of GPIO direction & data registers at boot on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Enable time handling on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Make System IO Config Registers board configurable on MPC83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Fixed PCI indirect config ops to handle multiple PCI controllers
+ We need to adjust the bus number we are trying to access based
+ on which PCI controller its on
+ Patch by Kumar Gala, 12 Jan 2006
+
+* Report back PCI bus when doing table based device config
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added support for PCI prefetchable region and BARs
+ If a host controller sets up a region as prefetchable and
+ a device's BAR denotes it as prefetchable, allocate the
+ BAR into the prefetch region.
+
+ If a BAR is prefetchable and no prefetchable region has
+ been setup by the controller we fall back to allocating
+ the BAR into the normally memory region.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add helper function for generic flat device tree fixups for mpc83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for passing initrd information via flat device tree
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added OF_STDOUT_PATH and OF_SOC
+
+ OF_STDOUT_PATH specifies the path to the device the kernel can use
+ for console output
+
+ OF_SOC specifies the proper name of the SOC node if one exists.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow board code to fixup the flat device tree before booting a kernel
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added CONFIG_ options for bd_t and env in flat dev tree
+
+ CONFIG_OF_HAS_BD_T will put a copy of the bd_t
+ into the resulting flat device tree.
+
+ CONFIG_OF_HAS_UBOOT_ENV will copy the environment
+ variables from u-boot into the flat device tree
+
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for the DHCP vendor optional bootfile (#67).
+ Ignores the vendor TFTP server name option (#66).
+ Patch by Murray Jensen, 30 Jun 2005
+
+* Fix a HW timing issue on 8548 CDS for eTSEC 3 in RGMII mode
+ Patch by Andy Fleming, 14 Jun 2005
+
+* Fix bad register definitions for LTX971 PHY on MPC85xx boards.
+ Patch by Gerhard Jaeger, 21 Jun 2005
+
+* Add netconsole and some more commands to RPXlite_DW board
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix bad declaration on pci_cfgfunc_nothing
+ Patch by Sam Song, 19 Jun 2005
+
+* Adjust "echo" as a default command
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix PCIDF calculation in cpu/mpc8260/speed.c for MPC8280EC
+ Patch by KokHow Teh, 16 Jun 2005
+
+* Add crc of data to jffs2 (in jffs2_1pass_build_lists()).
+ Patch by Rick Bronson, 15 Jun 2005
+
+* Coding Style cleanup
+
+* Avoid dereferencing NULL in find_cmd() if no valid commands were found
+ Patch by Andrew Dyer, 13 Jun 2005
+
+* Add ADI Blackfin support
+ - add support for Analog Devices Blackfin BF533 CPU
+ - add support for the ADI BF533 Stamp uClinux board
+ - add support for the ADI BF533 EZKit board
+ Patches by Richard Klingler, 11 Jun 2005
+
+* Add loads of ntohl() in image header handling
+ Patch by Steven Scholz, 10 Jun 2005
+
+* Switch MPC86xADS and MPC885ADS boards to use cpuclk environment
+ variable to set clock
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* RPXlite configuration fixes
+ - Use correct flash sector size
+ - Use correct memory test end address
+ - Add support for bzip2 compression
+ - Various small fixes
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Memory configuration changes for ZPC.1900 board
+ - Fix SDRAM timing on both local bus and 60x bus
+ - Add support for second flash bank (SIMM)
+ - Change boot flash base
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Add support for Adder boards with 16MB SDRAM;
+ add support for second FEC on Adder87x board.
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Fix conditional for including ks8695eth driver
+ Patch by Greg Ungerer, 04 Jun 2005
+
+* Fix Makefile: include config.mk only after CROSS_COMPILE is defined
+ Patch by Friedrich Lobenstock, 02 Jun 2005
+
+* Fix comment in common/soft_i2c.c
+ Patches by Peter Korsgaard/Tolunay Orkun, 26 May 2005
+
+* Cleanup compiler warnings.
+ Patch by Greg Ungerer, 21 May 2005
+
+* Word alignment fixes for word aligned NS16550 UART
+ Patch by Jean-Paul Saman, 01 Mar 2005
+
+ Fixes bug with UART that only supports word aligned access: removed
+ "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" some
+ (broken!) versions of GCC generate byte accesses when encountering
+ the packed attribute regardless if the struct is already correctly
+ aligned for a platform. Peripherals that can only handle word
+ aligned access won't work properly when accessed with byte access.
+ The struct NS16550 is already word aligned for REG_SIZE = 4, so
+ there is no need to packed the struct in that case.
+
+* Fix behaviour if gatewayip is not set
+ Patch by Robin Gilks, 23 Dec 2004
+
+* Fix cleanup for netstart board.
+ Remove build results from repository
+
+* Some code cleanup for GCC 4.x
+
+* Fixes to support environment in NAND flash;
+ enable NAND flash based environment for delta board.
+
+* Add support for Intel Monahans CPU on Zylonite and Delta boards
+ (This is Work in Progress!)
+
+* Add support for TQM8260-AI boards.
+
+* Minor code cleanup
+
+* Merge the new NAND code (testing-NAND brach); see doc/README.nand
+ Rewrite of NAND code based on what is in 2.6.12 Linux kernel
+ Patch by Ladislav Michl, 29 Jun 2005
+
+* Add lowboot target to mcc200 board
+ Patch by Stefan Roese, 4 Mar 2006
+
+* Fix problem with flash_get_size() from CFI driver update
+ Patch by Stefan Roese, 1 Mar 2006
+
+* Make CFG_NO_FLASH work on ARM systems
+ Patch by Markus Klotzbuecher, 27 Feb 2006
+
+* Update mcc200 config: Disable PCI and DoC, use 133 MHz IPB clock,
+ use hush shell.
+
+* Convert mcc200 to use common CFI flash driver
+ Patch by Stefan Roese, 28 Feb 2006
+
+* Add env-variable "unlock" to handle initial state of sectors
+ (locked/unlocked).
+
+ Only the U-Boot image and it's environment is protected,
+ all other sectors are unprotected (unlocked) if flash
+ hardware protection is used (CFG_FLASH_PROTECTION) and
+ the environment variable "unlock" is set to "yes".
+
+ Patch by Stefan Roese, 28 Feb 2006
+
+* Update drivers/cfi_flash.c:
+ - find_sector() called in both versions of flash_write_cfiword()
+ Patch by Peter Pearse, 27th Feb 2006
+
+* CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode
+ Patch by Jose Maria Lopez, 16 Jan 2006
+
+* Add support for AMD/Spansion Flashes in flash_write_cfibuffer
+ Patch by Alex Bastos and Thomas Schaefer, 2005-08-29
+
+* Changes/fixes for drivers/cfi_flash.c:
+ We *should* check if there are any error bits if the previous call
+ returned ERR_OK (Otherwise we will have output an error message in
+ flash_status_check() already.) The original code would only check for
+ error bits if flash_status_check() returns ERR_TIMEOUT.
+ Patch by Marcus Hall, 23 Aug 2005
+
+* Changes/fixes for drivers/cfi_flash.c:
+ - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c
+ - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c
+ Patch by Sangmoon Kim, 19 Aug 2005
+
+* Fixes for drivers/cfi_flash.c:
+ - Fix wrong timeout value usage in flash_status_check()
+ - Round write_tout up when converting to msec in flash_get_size()
+ - Remove clearing flash status at the end of flash_write_cfibuffer()
+ which sets Intel 28F640J3 flash back to command mode on CSB472
+ Patch by Tolunay Orkun, 02 July 2005
+
+* Add basic support for the SMMACO4 Board from PanDaCom.
+ Patch by Heiko Schocher, 20 Feb 2006
+
+* Add GIT version information (commid ID) to untagged U-Boot versions
+
+ As done in the linux kernel, the U-Boot version (U_BOOT_VERSION)
+ of all unreleased (untagged) U-Boot images will be automatically
+ extended upon compiletime with a part of the GIT commit ID and
+ possibly with "dirty" if uncommited changes are detected.
+
+ Here an example for the resulting version:
+ "U-Boot 1.1.4-g3457ac18-dirty"
+
+ The version is now maintained in the toplevel Makefile and the
+ version headers are autogenerated.
+
+ Patch by Stefan Roese, 9 Feb 2006
+
+* Update default environment for INKA4x00 board.
+
+* Convert CPCI750 to use common CFI flash driver
+ Patch by Reinhard Arlt, 8 Feb 2006
+
+* Various changes to esd HH405 board specific files
+ Patch by Matthias Fuchs, 07 Feb 2006
+
+* Cleanup U-Boot boot messages on ARM.
+
+ To match the U-Boot user interface on ARM platforms to the U-Boot
+ standard (as on PPC platforms), some messages with debug character
+ are removed from the default U-Boot build.
+ Enable DEBUG for lib_arm/board.c to enable debug messages.
+ New CONFIG_DISPLAY_CPUINFO and CONFIG_DISPLAY_BOARDINFO options.
+ Patch by Stefan Roese, 24 Jan 2006
+
+* Fix various compiler warnings on ppc4xx builds (ELDK 4.0)
+ Patch by Stefan Roese, 18 Jan 2006
+
+* Add VGA support (CT69000) to CPCI750 board.
+ Insert missing __le32_to_cpu() for filesize in ext2fs_read_file().
+ Patch by Reinhard Arlt, 30 Dec 2005
+
+* PMC405 and CPCI405: Moved configuration of pci resources
+ into config file.
+ PMC405 and CPCI2DP: Added firmware download and booting via pci.
+ Patch by Matthias Fuchs, 20 Dec 2005
+
+* Fix 28F256J3A support on PM520 board
+ (without bank-switching only 32 MB can be accessed)
+
+* Fix mkimage bug with multifile images created on 64 bit systems.
+
+* Add support for 28F256J3A flash (=> 64 MB) on PM520 board
+
+* Fix compiler problem with at91rm9200dk board.
+ Patch by Eugen Bigz, 19 Dec 2005
+
======================================================================
Changes for U-Boot 1.1.4:
======================================================================
+* Changes to Yellowstone & Yosemite 440EP/GR eval boards:
+ - Changed GPIO setup to enable another address line in order to
+ address 64M of FLASH.
+ - Added function sdram_tr1_set to auto calculate the tr1 value for
+ the DDR.
+ Patch by Steven Blakeslee, 12 Dec 2005
+
+* MPC5200: Set PCI retry counter to 0 = infinite retry;
+ The default of 255 is too short for slow devices.
+ Patch by Martin Nykodym, 12 Dec 2005
+
+* Change port configuration for O2DNT (CODEC1 on PSC1).
+
+* Fix register for PCI async mode on PPC440EP
+ Patch by Youngchul Bang, 08 Dec 2005
+
+* Fix U-Boot linking problems (add .eh_frame segment to linker script)
+ This segment may be required by some libgcc.a functions
+ (like _udivdi3).
+
+* Fix DPRAM offset/size for MPC8541/8555.
+ Simplify TQM85xx Makefile handling.
+
+* Fix data overflow (typo?) in rtc/ds1302.c
+
+* Fix U-Boot compilation for MIPS boards using ELDK 4.0
+
+* Add support for TQM8541/8555 boards, TQM85xx support reworked:
+ - Support for TQM8541/8555 boards added.
+ - Complete rework of TQM8540/8560 support.
+ - Common TQM85xx code now supports all current TQM85xx platforms
+ (TQM8540/8541/8555/8560).
+ - DDR SDRAM size detection added.
+ - CAS latency default values can be overwritten by setting "serial#"
+ to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
+ If problems are detected with this non default CAS latency,
+ the default values will be used instead.
+ - Flash size detection added.
+ - Moved FCC ethernet driver initialization behind TSEC driver init
+ -> TSEC is first device.
+ Patch by Stefan Roese, 30 Nov 2005
+
* Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
Patch by John Otken, 23 Nov 2005
* Changed PPC44x startup message (cpu info, speed...) to common style:
On PPC44x platforms, the startup message generated in "cpu.c" only
- comprised the ppc type and revision but not additional informations
+ comprised the ppc type and revision but not additional information
like speed etc. Those speed infos where printed in the board specific
code. This new implementation now prints all CPU infos in the common
cpu specific code. No board specific code is needed anymore and
therefore removed from all current 44x implementations.
Patch by Stefan Roese, 27 Nov 2005
+* Adjust TQM834x PHY addresses for latest hardware revision.
+
+* Increase malloc arena on TQM5200 board to 256 kB.
+ With 64 kb uniform flash sector size the old value of 128 kB was
+ too small.
+
+* Fix miiphy global data initialization (problem on 4xx boards when
+ no ethaddr is assigned). Initialization moved from
+ miiphy_register() to eth_initialize().
+
+ Based on initial patch for 4xx platform by Matthias Fuchs.
+
* Remove unnnecessary #include <linux/types.h> from include/asm-*/u-boot.h
* Allow use of include/image.h and include/asm-*/u-boot.h in proprietary code.
projects / karo-tx-uboot.git / blobdiff