mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.

[karo-tx-uboot.git] / Kconfig

diff --git a/Kconfig b/Kconfig
index 79259dec4a6a086415d3da646805064cd24f39fe..d9183d605d1cbccea8750c8e1679bac45e0c3f66 100644 (file)
--- a/Kconfig
+++ b/Kconfig
@@ -54,7 +54,7 @@ config CC_OPTIMIZE_FOR_SIZE
 
 config SYS_MALLOC_F
        bool "Enable malloc() pool before relocation"
 
 config SYS_MALLOC_F
        bool "Enable malloc() pool before relocation"

-       default 0x400
+       default y if DM

        help
          Before relocation memory is very limited on many platforms. Still,
          we can provide a small malloc() pool if needed. Driver model in
        help
          Before relocation memory is very limited on many platforms. Still,
          we can provide a small malloc() pool if needed. Driver model in


@@ -72,13 +72,31 @@ config SYS_MALLOC_F_LEN
          initial serial device and any others that are needed.
 
 menuconfig EXPERT
          initial serial device and any others that are needed.
 
 menuconfig EXPERT

-        bool "Configure standard U-Boot features (expert users)"
-        help
-          This option allows certain base U-Boot options and settings
-          to be disabled or tweaked. This is for specialized
-          environments which can tolerate a "non-standard" U-Boot.
-          Only use this if you really know what you are doing.
-
+       bool "Configure standard U-Boot features (expert users)"
+       default y
+       help
+         This option allows certain base U-Boot options and settings
+         to be disabled or tweaked. This is for specialized
+         environments which can tolerate a "non-standard" U-Boot.
+         Only use this if you really know what you are doing.
+
+if EXPERT
+       config SYS_MALLOC_CLEAR_ON_INIT
+       bool "Init with zeros the memory reserved for malloc (slow)"
+       default y
+       help
+         This setting is enabled by default. The reserved malloc
+         memory is initialized with zeros, so first malloc calls
+         will return the pointer to the zeroed memory. But this
+         slows the boot time.
+
+         It is recommended to disable it, when CONFIG_SYS_MALLOC_LEN
+         value, has more than few MiB, e.g. when uses bzip2 or bmp logo.
+         Then the boot time can be significantly reduced.
+         Warning:
+         When disabling this, please check if malloc calls, maybe
+         should be replaced by calloc - if expects zeroed memory.
+endif

 endmenu                # General setup
 
 menu "Boot images"
 endmenu                # General setup
 
 menu "Boot images"


@@ -96,6 +114,24 @@ config SPL
        help
          If you want to build SPL as well as the normal image, say Y.
 
        help
          If you want to build SPL as well as the normal image, say Y.
 

+config SPL_STACK_R
+       depends on SPL
+       bool "Enable SDRAM location for SPL stack"
+       help
+         SPL starts off execution in SRAM and thus typically has only a small
+         stack available. Since SPL sets up DRAM while in its board_init_f()
+         function, it is possible for the stack to move there before
+         board_init_r() is reached. This option enables a special SDRAM
+         location for the SPL stack. U-Boot SPL switches to this after
+         board_init_f() completes, and before board_init_r() starts.
+
+config SPL_STACK_R_ADDR
+       depends on SPL_STACK_R
+       hex "SDRAM location for SPL stack"
+       help
+         Specify the address in SDRAM for the SPL stack. This will be set up
+         before board_init_r() is called.
+

 config TPL
        bool
        depends on SPL && SUPPORT_TPL
 config TPL
        bool
        depends on SPL && SUPPORT_TPL


@@ -123,7 +159,9 @@ config FIT_SIGNATURE
        select RSA
        help
          This option enables signature verification of FIT uImages,
        select RSA
        help
          This option enables signature verification of FIT uImages,

-         using a hash signed and verified using RSA.
+         using a hash signed and verified using RSA. If
+         CONFIG_SHA_PROG_HW_ACCEL is defined, i.e support for progressive
+         hashing is available using hardware, RSA library will use it.

          See doc/uImage.FIT/signature.txt for more details.
 
 config SYS_EXTRA_OPTIONS
          See doc/uImage.FIT/signature.txt for more details.
 
 config SYS_EXTRA_OPTIONS


@@ -140,13 +178,14 @@ config SYS_EXTRA_OPTIONS
          new boards should not use this option.
 
 config SYS_TEXT_BASE
          new boards should not use this option.
 
 config SYS_TEXT_BASE

-       depends on SPARC || ARC
+       depends on SPARC || ARC || X86 || ARCH_UNIPHIER || ARCH_ZYNQMP
+       depends on !EFI_APP

        hex "Text Base"
        help
          TODO: Move CONFIG_SYS_TEXT_BASE for all the architecture
 
 config SYS_CLK_FREQ
        hex "Text Base"
        help
          TODO: Move CONFIG_SYS_TEXT_BASE for all the architecture
 
 config SYS_CLK_FREQ

-       depends on ARC
+       depends on ARC || ARCH_SUNXI

        int "CPU clock frequency"
        help
          TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture
        int "CPU clock frequency"
        help
          TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture