imx: correct HAB status for new chip TO

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 61851b3d888c98223832554785a774674c318037..a280435e9fbec65012cf9758a66f6827d2f22353 100644 (file)
--- a/README
+++ b/README
@@ -264,6 +264,17 @@ e.g. "make cogent_mpc8xx_config". And also configure the cogent
 directory according to the instructions in cogent/README.
 
 
+Sandbox Environment:
+--------------------
+
+U-Boot can be built natively to run on a Linux host using the 'sandbox'
+board. This allows feature development which is not board- or architecture-
+specific to be undertaken on a native platform. The sandbox is also used to
+run some of U-Boot's tests.
+
+See board/sandbox/sandbox/README.sandbox for more details.
+
+
 Configuration Options:
 ----------------------
 
@@ -440,6 +451,12 @@ The following options need to be configured:
                supported, core will start to execute uboot when wakes up.
 
 - Generic CPU options:
+               CONFIG_SYS_GENERIC_GLOBAL_DATA
+               Defines global data is initialized in generic board board_init_f().
+               If this macro is defined, global data is created and cleared in
+               generic board board_init_f(). Without this macro, architecture/board
+               should initialize global data before calling board_init_f().
+
                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
                Defines the endianess of the CPU. Implementation of those
@@ -740,6 +757,10 @@ The following options need to be configured:
                boot loader that has already initialized the UART.  Define this
                variable to flush the UART at init time.
 
+               CONFIG_SERIAL_HW_FLOW_CONTROL
+
+               Define this variable to enable hw flow control in serial driver.
+               Current user of this option is drivers/serial/nsl16550.c driver
 
 - Console Interface:
                Depending on board, define exactly one serial port
@@ -1513,6 +1534,16 @@ The following options need to be configured:
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 
+               CONFIG_GENERIC_MMC
+               Enable the generic MMC driver
+
+               CONFIG_SUPPORT_EMMC_BOOT
+               Enable some additional features of the eMMC boot partitions.
+
+               CONFIG_SUPPORT_EMMC_RPMB
+               Enable the commands for reading, writing and programming the
+               key for the Replay Protection Memory Block partition in eMMC.
+
 - USB Device Firmware Update (DFU) class support:
                CONFIG_DFU_FUNCTION
                This enables the USB portion of the DFU USB class
@@ -1558,6 +1589,28 @@ The following options need to be configured:
                entering dfuMANIFEST state. Host waits this timeout, before
                sending again an USB request to the device.
 
+- USB Device Android Fastboot support:
+               CONFIG_CMD_FASTBOOT
+               This enables the command "fastboot" which enables the Android
+               fastboot mode for the platform's USB device. Fastboot is a USB
+               protocol for downloading images, flashing and device control
+               used on Android devices.
+               See doc/README.android-fastboot for more information.
+
+               CONFIG_ANDROID_BOOT_IMAGE
+               This enables support for booting images which use the Android
+               image format header.
+
+               CONFIG_USB_FASTBOOT_BUF_ADDR
+               The fastboot protocol requires a large memory buffer for
+               downloads. Define this to the starting RAM address to use for
+               downloaded images.
+
+               CONFIG_USB_FASTBOOT_BUF_SIZE
+               The fastboot protocol requires a large memory buffer for
+               downloads. This buffer should be as large as possible for a
+               platform. Define this to the size available RAM for fastboot.
+
 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
                CONFIG_JFFS2_NAND_DEV
@@ -2529,6 +2582,19 @@ CBFS (Coreboot Filesystem) support
 
                Specify the number of FPGA devices to support.
 
+               CONFIG_CMD_FPGA_LOADMK
+
+               Enable support for fpga loadmk command
+
+               CONFIG_CMD_FPGA_LOADP
+
+               Enable support for fpga loadp command - load partial bitstream
+
+               CONFIG_CMD_FPGA_LOADBP
+
+               Enable support for fpga loadbp command - load partial bitstream
+               (Xilinx only)
+
                CONFIG_SYS_FPGA_PROG_FEEDBACK
 
                Enable printing of hash marks during FPGA configuration.