the LCD display every second with
a "rotator" |\-/|\-/
-- Board flavour: (if CONFIG_MPC8260ADS is defined)
- CONFIG_ADSTYPE
- Possible values are:
- CONFIG_SYS_8260ADS - original MPC8260ADS
- CONFIG_SYS_8266ADS - MPC8266ADS
- CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
- CONFIG_SYS_8272ADS - MPC8272ADS
-
- Marvell Family Member
CONFIG_SYS_MVFS - define it if you want to enable
multiple fs option at one time
CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
CONFIG_CMD_IRQ * irqinfo
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
+- I/O tracing:
+ When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
+ accesses and can checksum them or write a list of them out
+ to memory. See the 'iotrace' command for details. This is
+ useful for testing device drivers since it can confirm that
+ the driver behaves the same way before and after a code
+ change. Currently this is supported on sandbox and arm. To
+ add support for your architecture, add '#include <iotrace.h>'
+ to the bottom of arch/<arch>/include/asm/io.h and test.
+
+ Example output from the 'iotrace stats' command is below.
+ Note that if the trace buffer is exhausted, the checksum will
+ still continue to operate.
+
+ iotrace is enabled
+ Start: 10000000 (buffer start address)
+ Size: 00010000 (buffer size)
+ Offset: 00000120 (current buffer offset)
+ Output: 10000120 (start + offset)
+ Count: 00000018 (number of trace records)
+ CRC32: 9526fb66 (CRC32 of all trace records)
+
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
- CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
- interval for usb hub power-on delay.(minimum 100msec)
-
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
CONFIG_SH_MMCIF_CLK
Define the clock frequency for MMCIF
+ CONFIG_GENERIC_MMC
+ Enable the generic MMC driver
+
+ CONFIG_SUPPORT_EMMC_BOOT
+ Enable some additional features of the eMMC boot partitions.
+
+ CONFIG_SUPPORT_EMMC_RPMB
+ Enable the commands for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
- USB Device Firmware Update (DFU) class support:
CONFIG_DFU_FUNCTION
This enables the USB portion of the DFU USB class
filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
and cbfsload.
+- FAT(File Allocation Table) filesystem cluster size:
+ CONFIG_FS_FAT_MAX_CLUSTSIZE
+
+ Define the max cluster size for fat operations else
+ a default value of 65536 will be defined.
+
- Keyboard Support:
CONFIG_ISA_KEYBOARD
-150 common/cmd_nand.c Incorrect FIT image format
151 common/cmd_nand.c FIT image format OK
+- legacy image format:
+ CONFIG_IMAGE_FORMAT_LEGACY
+ enables the legacy image format support in U-Boot.
+
+ Default:
+ enabled if CONFIG_FIT_SIGNATURE is not defined.
+
+ CONFIG_DISABLE_IMAGE_LEGACY
+ disable the legacy image format
+
+ This define is introduced, as the legacy image format is
+ enabled per default for backward compatibility.
+
- FIT image support:
CONFIG_FIT
Enable support for the FIT uImage format.
using a hash signed and verified using RSA. See
doc/uImage.FIT/signature.txt for more details.
+ WARNING: When relying on signed FIT images with required
+ signature check the legacy image format is default
+ disabled. If a board need legacy image format support
+ enable this through CONFIG_IMAGE_FORMAT_LEGACY
+
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
projects / karo-tx-uboot.git / blobdiff