galaxy5200: change cs1 configuration

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 90714727cde2d714643b2ac11d246bf41ec74627..dee0e674a18c007fa98393db9a7d3b0a70e8a42b 100644 (file)
--- a/README
+++ b/README
@@ -368,8 +368,10 @@ The following options need to be configured:
                 * Adds the "fdt" command
                 * The bootm command automatically updates the fdt
 
-               OF_CPU - The proper name of the cpus node.
-               OF_SOC - The proper name of the soc node.
+               OF_CPU - The proper name of the cpus node (only required for
+                       MPC512X and MPC5xxx based boards).
+               OF_SOC - The proper name of the soc node (only required for
+                       MPC512X and MPC5xxx based boards).
                OF_TBCLK - The timebase frequency.
                OF_STDOUT_PATH - The path to the console device
 
@@ -386,6 +388,15 @@ The following options need to be configured:
                This define fills in the correct boot CPU in the boot
                param header, the default value is zero if undefined.
 
+               CONFIG_OF_IDE_FIXUP
+
+               U-Boot can detect if an IDE device is present or not.
+               If not, and this new config option is activated, U-Boot
+               removes the ATA node from the DTS before booting Linux,
+               so the Linux IDE driver does not probe the device and
+               crash. This is needed for buggy hardware (uc101) where
+               no pull down resistor is connected to the signal IDE5V_DD7.
+
 - vxWorks boot parameters:
 
                bootvx constructs a valid bootline using the following
@@ -629,6 +640,8 @@ The following options need to be configured:
                CONFIG_CMD_KGDB         * kgdb
                CONFIG_CMD_LOADB          loadb
                CONFIG_CMD_LOADS          loads
+               CONFIG_CMD_MD5SUM         print md5 message digest
+                                         (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,
                                          loop, loopw, mtest
                CONFIG_CMD_MISC           Misc functions like sleep etc
@@ -652,6 +665,8 @@ The following options need to be configured:
                                          (requires CONFIG_CMD_I2C)
                CONFIG_CMD_SETGETDCR      Support for DCR Register access
                                          (4xx only)
+               CONFIG_CMD_SHA1           print sha1 memory digest
+                                         (requires CONFIG_CMD_MEMORY)
                CONFIG_CMD_SOURCE         "source" command Support
                CONFIG_CMD_SPI          * SPI serial bus support
                CONFIG_CMD_USB          * USB support
@@ -854,9 +869,13 @@ The following options need to be configured:
                MPC5200 USB requires additional defines:
                        CONFIG_USB_CLOCK
                                for 528 MHz Clock: 0x0001bbbb
+                       CONFIG_PSC3_USB
+                               for USB on PSC3
                        CONFIG_USB_CONFIG
                                for differential drivers: 0x00001000
                                for single ended drivers: 0x00005000
+                               for differential drivers on PSC3: 0x00000100
+                               for single ended drivers on PSC3: 0x00004100
                        CONFIG_SYS_USB_EVENT_POLL
                                May be defined to allow interrupt polling
                                instead of using asynchronous interrupts
@@ -1358,6 +1377,13 @@ The following options need to be configured:
                therefore be cleared to 0 (See, eg, MPC823e User's Manual
                p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0.
 
+               CONFIG_SYS_I2C_INIT_MPC5XXX
+
+               When a board is reset during an i2c bus transfer
+               chips might think that the current transfer is still
+               in progress.  Reset the slave devices by sending start
+               commands until the slave device responds.
+
                That's all that's required for CONFIG_HARD_I2C.
 
                If you use the software i2c interface (CONFIG_SOFT_I2C)
@@ -2993,14 +3019,6 @@ Some configuration options can be set using Environment Variables:
                  configuration from the BOOTP server, but not try to
                  load any image using TFTP
 
-  autoscript   - if set to "yes" commands like "loadb", "loady",
-                 "bootp", "tftpb", "rarpboot" and "nfs" will attempt
-                 to automatically run script images (by internally
-                 calling "source").
-
-  autoscript_uname - if script image is in a format (FIT) this
-                    variable is used to get script subimage unit name.
-
   autostart    - if set to "yes", an image loaded using the "bootp",
                  "rarpboot", "tftpboot" or "diskboot" commands will
                  be automatically started (by internally calling
@@ -3904,10 +3922,10 @@ For PowerPC, the following registers have specific use:
     average for all boards 752 bytes for the whole U-Boot image,
     624 text + 127 data).
 
-On Blackfin, the normal C ABI (except for P5) is followed as documented here:
+On Blackfin, the normal C ABI (except for P3) is followed as documented here:
        http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
 
-    ==> U-Boot will use P5 to hold a pointer to the global data
+    ==> U-Boot will use P3 to hold a pointer to the global data
 
 On ARM, the following registers are used: