* Patches by Xianghua Xiao, 15 Oct 2003:

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 617abb409ce1fecd03287e18a074b6e68fdeb634..e3f4f9ddd41d89632c57795245b7fe7fe89ce43a 100644 (file)
--- a/README
+++ b/README
@@ -146,6 +146,7 @@ Directory Hierarchy:
 - cpu/mpc8xx   Files specific to Motorola MPC8xx  CPUs
 - cpu/mpc824x  Files specific to Motorola MPC824x CPUs
 - cpu/mpc8260  Files specific to Motorola MPC8260 CPU
+- cpu/mpc85xx  Files specific to Motorola MPC85xx CPUs
 - cpu/ppc4xx   Files specific to IBM      4xx     CPUs
 
 
@@ -199,6 +200,10 @@ Directory Hierarchy:
 - board/mbx8xx Files specific to MBX        boards
 - board/mpc8260ads
                Files specific to MPC8260ADS and PQ2FADS-ZU boards
+- board/mpc8540ads
+               Files specific to MPC8540ADS boards
+- board/mpc8560ads
+               Files specific to MPC8560ADS boards
 - board/mpl/   Files specific to boards manufactured by MPL
 - board/mpl/common     Common files for MPL boards
 - board/mpl/pip405     Files specific to PIP405     boards
@@ -210,7 +215,7 @@ Directory Hierarchy:
 - board/oxc    Files specific to OXC        boards
 - board/omap1510inn
                Files specific to OMAP 1510 Innovator boards
-- board/omap1610inn  
+- board/omap1610inn
                Files specific to OMAP 1610 Innovator boards
 - board/pcippc2        Files specific to PCIPPC2/PCIPPC6 boards
 - board/pm826  Files specific to PM826      boards
@@ -306,6 +311,7 @@ The following options need to be configured:
                CONFIG_MPC823,  CONFIG_MPC850,  CONFIG_MPC855,  CONFIG_MPC860
        or      CONFIG_MPC5xx
        or      CONFIG_MPC824X, CONFIG_MPC8260
+       or      CONFIG_MPC85xx
        or      CONFIG_IOP480
        or      CONFIG_405GP
        or      CONFIG_405EP
@@ -356,7 +362,8 @@ The following options need to be configured:
                CONFIG_IAD210,     CONFIG_RPXlite,    CONFIG_sbc8260,
                CONFIG_EBONY,      CONFIG_sacsng,     CONFIG_FPS860L,
                CONFIG_V37,        CONFIG_ELPT860,    CONFIG_CMI,
-               CONFIG_NETVIA,     CONFIG_RBC823,     CONFIG_ZPC1900
+               CONFIG_NETVIA,     CONFIG_RBC823,     CONFIG_ZPC1900,
+               CONFIG_MPC8540ADS, CONFIG_MPC8560ADS
 
                ARM based boards:
                -----------------
@@ -591,7 +598,7 @@ The following options need to be configured:
                CFG_CMD_DHCP      DHCP support
                CFG_CMD_DIAG    * Diagnostics
                CFG_CMD_DOC     * Disk-On-Chip Support
-               CFG_CMD_DTT       Digital Therm and Thermostat 
+               CFG_CMD_DTT       Digital Therm and Thermostat
                CFG_CMD_ECHO    * echo arguments
                CFG_CMD_EEPROM  * EEPROM read/write support
                CFG_CMD_ELF       bootelf, bootvx
@@ -893,9 +900,9 @@ The following options need to be configured:
                images is included. If not, only uncompressed and gzip
                compressed images are supported.
 
-                NOTE: the bzip2 algorithm requires a lot of RAM, so
-                the malloc area (as defined by CFG_MALLOC_LEN) should
-                be at least 4MB.
+               NOTE: the bzip2 algorithm requires a lot of RAM, so
+               the malloc area (as defined by CFG_MALLOC_LEN) should
+               be at least 4MB.
 
 - Ethernet address:
                CONFIG_ETHADDR
@@ -1757,13 +1764,13 @@ the default environment is used; a new CRC is computed as soon as you
 use the "saveenv" command to store a valid environment.
 
 - CFG_FAULT_ECHO_LINK_DOWN:
-               Echo the inverted Ethernet link state to the fault LED.
+               Echo the inverted Ethernet link state to the fault LED.
 
                Note: If this option is active, then CFG_FAULT_MII_ADDR
                      also needs to be defined.
 
 - CFG_FAULT_MII_ADDR:
-               MII address of the PHY to check for the Ethernet link state.
+               MII address of the PHY to check for the Ethernet link state.
 
 Low Level (hardware related) configuration options:
 ---------------------------------------------------
@@ -1774,9 +1781,9 @@ Low Level (hardware related) configuration options:
 - CFG_DEFAULT_IMMR:
                Default address of the IMMR after system reset.
 
-                Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
-                and RPXsuper) to be able to adjust the position of
-                the IMMR register after a reset.
+               Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
+               and RPXsuper) to be able to adjust the position of
+               the IMMR register after a reset.
 
 - Floppy Disk Support:
                CFG_FDC_DRIVE_NUMBER
@@ -1950,7 +1957,8 @@ configurations; the following names are supported:
     GEN860T_config       EBONY_config          FPS860L_config
     ELPT860_config       cmi_mpc5xx_config     NETVIA_config
     at91rm9200dk_config          omap1510inn_config    MPC8260ADS_config
-    omap1610inn_config   ZPC1900_config
+    omap1610inn_config   ZPC1900_config        MPC8540ADS_config
+    MPC8560ADS_config
 
 Note: for some board special configuration names may exist; check  if
       additional  information is available from the board vendor; for