#include <nand.h>
#include <linux/err.h>
#include <asm/io.h>
-#if defined(CONFIG_MX27) || defined(CONFIG_MX25)
+#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35) || \
+ defined(CONFIG_MX51) || defined(CONFIG_MX53)
#include <asm/arch/imx-regs.h>
#endif
+#include "mxc_nand.h"
#define DRIVER_NAME "mxc_nand"
-/*
- * TODO: Use same register defs here as nand_spl mxc nand driver.
- */
-/*
- * Register map and bit definitions for the Freescale NAND Flash Controller
- * present in various i.MX devices.
- *
- * MX31 and MX27 have version 1 which has
- * 4 512 byte main buffers and
- * 4 16 byte spare buffers
- * to support up to 2K byte pagesize nand.
- * Reading or writing a 2K page requires 4 FDI/FDO cycles.
- *
- * MX25 has version 1.1 which has
- * 8 512 byte main buffers and
- * 8 64 byte spare buffers
- * to support up to 4K byte pagesize nand.
- * Reading or writing a 2K or 4K page requires only 1 FDI/FDO cycle.
- * Also some of registers are moved and/or changed meaning as seen below.
- */
-#if defined(CONFIG_MX31) || defined(CONFIG_MX27)
-#define MXC_NFC_V1
-#elif defined(CONFIG_MX25)
-#define MXC_NFC_V1_1
-#else
-#warning "MXC NFC version not defined"
-#endif
-
-#if defined(MXC_NFC_V1)
-#define NAND_MXC_NR_BUFS 4
-#define NAND_MXC_SPARE_BUF_SIZE 16
-#define NAND_MXC_REG_OFFSET 0xe00
-#define is_mxc_nfc_11() 0
-#elif defined(MXC_NFC_V1_1)
-#define NAND_MXC_NR_BUFS 8
-#define NAND_MXC_SPARE_BUF_SIZE 64
-#define NAND_MXC_REG_OFFSET 0x1e00
-#define is_mxc_nfc_11() 1
-#else
-#error "define CONFIG_NAND_MXC_VXXX to use mtd mxc nand driver"
-#endif
-struct nfc_regs {
- uint8_t main_area[NAND_MXC_NR_BUFS][0x200];
- uint8_t spare_area[NAND_MXC_NR_BUFS][NAND_MXC_SPARE_BUF_SIZE];
- /*
- * reserved size is offset of nfc registers
- * minus total main and spare sizes
- */
- uint8_t reserved1[NAND_MXC_REG_OFFSET
- - NAND_MXC_NR_BUFS * (512 + NAND_MXC_SPARE_BUF_SIZE)];
-#if defined(MXC_NFC_V1)
- uint16_t nfc_buf_size;
- uint16_t reserved2;
- uint16_t nfc_buf_addr;
- uint16_t nfc_flash_addr;
- uint16_t nfc_flash_cmd;
- uint16_t nfc_config;
- uint16_t nfc_ecc_status_result;
- uint16_t nfc_rsltmain_area;
- uint16_t nfc_rsltspare_area;
- uint16_t nfc_wrprot;
- uint16_t nfc_unlockstart_blkaddr;
- uint16_t nfc_unlockend_blkaddr;
- uint16_t nfc_nf_wrprst;
- uint16_t nfc_config1;
- uint16_t nfc_config2;
-#elif defined(MXC_NFC_V1_1)
- uint16_t reserved2[2];
- uint16_t nfc_buf_addr;
- uint16_t nfc_flash_addr;
- uint16_t nfc_flash_cmd;
- uint16_t nfc_config;
- uint16_t nfc_ecc_status_result;
- uint16_t nfc_ecc_status_result2;
- uint16_t nfc_spare_area_size;
- uint16_t nfc_wrprot;
- uint16_t reserved3[2];
- uint16_t nfc_nf_wrprst;
- uint16_t nfc_config1;
- uint16_t nfc_config2;
- uint16_t reserved4;
- uint16_t nfc_unlockstart_blkaddr;
- uint16_t nfc_unlockend_blkaddr;
- uint16_t nfc_unlockstart_blkaddr1;
- uint16_t nfc_unlockend_blkaddr1;
- uint16_t nfc_unlockstart_blkaddr2;
- uint16_t nfc_unlockend_blkaddr2;
- uint16_t nfc_unlockstart_blkaddr3;
- uint16_t nfc_unlockend_blkaddr3;
-#endif
-};
-
-/*
- * Set INT to 0, FCMD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Command operation
- */
-#define NFC_CMD 0x1
-
-/*
- * Set INT to 0, FADD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Address operation
- */
-#define NFC_ADDR 0x2
-
-/*
- * Set INT to 0, FDI to 1, rest to 0 in NFC_CONFIG2 Register
- * for Input operation
- */
-#define NFC_INPUT 0x4
-
-/*
- * Set INT to 0, FDO to 001, rest to 0 in NFC_CONFIG2 Register
- * for Data Output operation
- */
-#define NFC_OUTPUT 0x8
-
-/*
- * Set INT to 0, FD0 to 010, rest to 0 in NFC_CONFIG2 Register
- * for Read ID operation
- */
-#define NFC_ID 0x10
-
-/*
- * Set INT to 0, FDO to 100, rest to 0 in NFC_CONFIG2 Register
- * for Read Status operation
- */
-#define NFC_STATUS 0x20
-
-/*
- * Set INT to 1, rest to 0 in NFC_CONFIG2 Register for Read
- * Status operation
- */
-#define NFC_INT 0x8000
+struct mxc_nand_host {
+ struct mtd_info mtd;
+ struct nand_chip *nand;
-#ifdef MXC_NFC_V1_1
-#define NFC_4_8N_ECC (1 << 0)
-#else
-#define NFC_4_8N_ECC 0
+ struct mxc_nand_regs __iomem *regs;
+#ifdef MXC_NFC_V3_2
+ struct mxc_nand_ip_regs __iomem *ip_regs;
#endif
-#define NFC_SP_EN (1 << 2)
-#define NFC_ECC_EN (1 << 3)
-#define NFC_BIG (1 << 5)
-#define NFC_RST (1 << 6)
-#define NFC_CE (1 << 7)
-#define NFC_ONE_CYCLE (1 << 8)
-
-typedef enum {false, true} bool;
-
-struct mxc_nand_host {
- struct mtd_info mtd;
- struct nand_chip *nand;
-
- struct nfc_regs __iomem *regs;
- int spare_only;
- int status_request;
- int pagesize_2k;
- int clk_act;
- uint16_t col_addr;
- unsigned int page_addr;
+ int spare_only;
+ int status_request;
+ int pagesize_2k;
+ int clk_act;
+ uint16_t col_addr;
+ unsigned int page_addr;
};
static struct mxc_nand_host mxc_host;
.oobfree = { {2, 4}, {11, 11}, {27, 11}, {43, 11}, {59, 5} },
};
#endif
-#elif defined(MXC_NFC_V1_1)
+#elif defined(MXC_NFC_V2_1) || defined(MXC_NFC_V3_2)
#ifndef CONFIG_SYS_NAND_LARGEPAGE
static struct nand_ecclayout nand_hw_eccoob = {
.eccbytes = 9,
#endif
#endif
-#ifdef CONFIG_MX27
-static int is_16bit_nand(void)
-{
- struct system_control_regs *sc_regs =
- (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
-
- if (readl(&sc_regs->fmcr) & NF_16BIT_SEL)
- return 1;
- else
- return 0;
-}
-#elif defined(CONFIG_MX31)
-static int is_16bit_nand(void)
-{
- struct clock_control_regs *sc_regs =
- (struct clock_control_regs *)CCM_BASE;
-
- if (readl(&sc_regs->rcsr) & CCM_RCSR_NF16B)
- return 1;
- else
- return 0;
-}
-#elif defined(CONFIG_MX25)
static int is_16bit_nand(void)
{
- struct ccm_regs *ccm =
- (struct ccm_regs *)IMX_CCM_BASE;
-
- if (readl(&ccm->rcsr) & CCM_RCSR_NF_16BIT_SEL)
- return 1;
- else
- return 0;
-}
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+ return 1;
#else
-#warning "8/16 bit NAND autodetection not supported"
-static int is_16bit_nand(void)
-{
return 0;
-}
#endif
+}
static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t size)
{
/*
* This function polls the NANDFC to wait for the basic operation to
- * complete by checking the INT bit of config2 register.
+ * complete by checking the INT bit.
*/
static void wait_op_done(struct mxc_nand_host *host, int max_retries,
uint16_t param)
uint32_t tmp;
while (max_retries-- > 0) {
- if (readw(&host->regs->nfc_config2) & NFC_INT) {
- tmp = readw(&host->regs->nfc_config2);
- tmp &= ~NFC_INT;
- writew(tmp, &host->regs->nfc_config2);
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
+ tmp = readnfc(&host->regs->config2);
+ if (tmp & NFC_V1_V2_CONFIG2_INT) {
+ tmp &= ~NFC_V1_V2_CONFIG2_INT;
+ writenfc(tmp, &host->regs->config2);
+#elif defined(MXC_NFC_V3_2)
+ tmp = readnfc(&host->ip_regs->ipc);
+ if (tmp & NFC_V3_IPC_INT) {
+ tmp &= ~NFC_V3_IPC_INT;
+ writenfc(tmp, &host->ip_regs->ipc);
+#endif
break;
}
udelay(1);
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_cmd(host, 0x%x)\n", cmd);
- writew(cmd, &host->regs->nfc_flash_cmd);
- writew(NFC_CMD, &host->regs->nfc_config2);
+ writenfc(cmd, &host->regs->flash_cmd);
+ writenfc(NFC_CMD, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, cmd);
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_addr(host, 0x%x)\n", addr);
- writew(addr, &host->regs->nfc_flash_addr);
- writew(NFC_ADDR, &host->regs->nfc_config2);
+ writenfc(addr, &host->regs->flash_addr);
+ writenfc(NFC_ADDR, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, addr);
}
/*
- * This function requests the NANDFC to initate the transfer
+ * This function requests the NANDFC to initiate the transfer
* of data currently in the NANDFC RAM buffer to the NAND device.
*/
static void send_prog_page(struct mxc_nand_host *host, uint8_t buf_id,
if (spare_only)
MTDDEBUG(MTD_DEBUG_LEVEL1, "send_prog_page (%d)\n", spare_only);
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21() || is_mxc_nfc_32()) {
int i;
/*
* The controller copies the 64 bytes of spare data from
}
}
- writew(buf_id, &host->regs->nfc_buf_addr);
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
+ writenfc(buf_id, &host->regs->buf_addr);
+#elif defined(MXC_NFC_V3_2)
+ uint32_t tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_V3_CONFIG1_RBA_MASK;
+ tmp |= NFC_V3_CONFIG1_RBA(buf_id);
+ writenfc(tmp, &host->regs->config1);
+#endif
/* Configure spare or page+spare access */
if (!host->pagesize_2k) {
- uint16_t config1 = readw(&host->regs->nfc_config1);
+ uint32_t config1 = readnfc(&host->regs->config1);
if (spare_only)
- config1 |= NFC_SP_EN;
+ config1 |= NFC_CONFIG1_SP_EN;
else
- config1 &= ~(NFC_SP_EN);
- writew(config1, &host->regs->nfc_config1);
+ config1 &= ~NFC_CONFIG1_SP_EN;
+ writenfc(config1, &host->regs->config1);
}
- writew(NFC_INPUT, &host->regs->nfc_config2);
+ writenfc(NFC_INPUT, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, spare_only);
}
/*
- * Requests NANDFC to initated the transfer of data from the
+ * Requests NANDFC to initiate the transfer of data from the
* NAND device into in the NANDFC ram buffer.
*/
static void send_read_page(struct mxc_nand_host *host, uint8_t buf_id,
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_read_page (%d)\n", spare_only);
- writew(buf_id, &host->regs->nfc_buf_addr);
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
+ writenfc(buf_id, &host->regs->buf_addr);
+#elif defined(MXC_NFC_V3_2)
+ uint32_t tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_V3_CONFIG1_RBA_MASK;
+ tmp |= NFC_V3_CONFIG1_RBA(buf_id);
+ writenfc(tmp, &host->regs->config1);
+#endif
/* Configure spare or page+spare access */
if (!host->pagesize_2k) {
- uint32_t config1 = readw(&host->regs->nfc_config1);
+ uint32_t config1 = readnfc(&host->regs->config1);
if (spare_only)
- config1 |= NFC_SP_EN;
+ config1 |= NFC_CONFIG1_SP_EN;
else
- config1 &= ~NFC_SP_EN;
- writew(config1, &host->regs->nfc_config1);
+ config1 &= ~NFC_CONFIG1_SP_EN;
+ writenfc(config1, &host->regs->config1);
}
- writew(NFC_OUTPUT, &host->regs->nfc_config2);
+ writenfc(NFC_OUTPUT, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, spare_only);
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21() || is_mxc_nfc_32()) {
int i;
/*
/* Request the NANDFC to perform a read of the NAND device ID. */
static void send_read_id(struct mxc_nand_host *host)
{
- uint16_t tmp;
+ uint32_t tmp;
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
/* NANDFC buffer 0 is used for device ID output */
- writew(0x0, &host->regs->nfc_buf_addr);
+ writenfc(0x0, &host->regs->buf_addr);
+#elif defined(MXC_NFC_V3_2)
+ tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_V3_CONFIG1_RBA_MASK;
+ writenfc(tmp, &host->regs->config1);
+#endif
/* Read ID into main buffer */
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_CONFIG1_SP_EN;
+ writenfc(tmp, &host->regs->config1);
- writew(NFC_ID, &host->regs->nfc_config2);
+ writenfc(NFC_ID, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, 0);
*/
static uint16_t get_dev_status(struct mxc_nand_host *host)
{
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
void __iomem *main_buf = host->regs->main_area[1];
uint32_t store;
- uint16_t ret, tmp;
+#endif
+ uint32_t ret, tmp;
/* Issue status request to NAND device */
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
/* store the main area1 first word, later do recovery */
store = readl(main_buf);
/* NANDFC buffer 1 is used for device status */
- writew(1, &host->regs->nfc_buf_addr);
+ writenfc(1, &host->regs->buf_addr);
+#endif
/* Read status into main buffer */
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_CONFIG1_SP_EN;
+ writenfc(tmp, &host->regs->config1);
- writew(NFC_STATUS, &host->regs->nfc_config2);
+ writenfc(NFC_STATUS, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, 0);
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
/*
* Status is placed in first word of main buffer
* get status, then recovery area 1 data
*/
ret = readw(main_buf);
writel(store, main_buf);
+#elif defined(MXC_NFC_V3_2)
+ ret = readnfc(&host->regs->config1) >> 16;
+#endif
return ret;
}
return 1;
}
-#ifdef CONFIG_MXC_NAND_HWECC
-static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode)
-{
- /*
- * If HW ECC is enabled, we turn it on during init. There is
- * no need to enable again here.
- */
-}
-
-#ifdef MXC_NFC_V1_1
static void _mxc_nand_enable_hwecc(struct mtd_info *mtd, int on)
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint16_t tmp = readw(&host->regs->nfc_config1);
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
+ uint16_t tmp = readnfc(&host->regs->config1);
if (on)
- tmp |= NFC_ECC_EN;
+ tmp |= NFC_V1_V2_CONFIG1_ECC_EN;
else
- tmp &= ~NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp &= ~NFC_V1_V2_CONFIG1_ECC_EN;
+ writenfc(tmp, &host->regs->config1);
+#elif defined(MXC_NFC_V3_2)
+ uint32_t tmp = readnfc(&host->ip_regs->config2);
+
+ if (on)
+ tmp |= NFC_V3_CONFIG2_ECC_EN;
+ else
+ tmp &= ~NFC_V3_CONFIG2_ECC_EN;
+ writenfc(tmp, &host->ip_regs->config2);
+#endif
+}
+
+#ifdef CONFIG_MXC_NAND_HWECC
+static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+ /*
+ * If HW ECC is enabled, we turn it on during init. There is
+ * no need to enable again here.
+ */
}
+#if defined(MXC_NFC_V2_1) || defined(MXC_NFC_V3_2)
static int mxc_nand_read_oob_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
- int page, int sndcmd)
+ int page)
{
struct mxc_nand_host *host = chip->priv;
uint8_t *buf = chip->oob_poi;
MTDDEBUG(MTD_DEBUG_LEVEL0,
"%s: Reading OOB area of page %u to oob %p\n",
- __FUNCTION__, host->page_addr, buf);
+ __func__, page, buf);
chip->cmdfunc(mtd, NAND_CMD_READOOB, mtd->writesize, page);
for (i = 0; i < chip->ecc.steps; i++) {
static int mxc_nand_read_page_raw_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
uint8_t *buf,
+ int oob_required,
int page)
{
struct mxc_nand_host *host = chip->priv;
int n;
_mxc_nand_enable_hwecc(mtd, 0);
- chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, host->page_addr);
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
for (n = 0, steps = chip->ecc.steps; steps > 0; n++, steps--) {
host->col_addr = n * eccsize;
size = mtd->oobsize - (oob - chip->oob_poi);
if (size)
chip->read_buf(mtd, oob, size);
- _mxc_nand_enable_hwecc(mtd, 0);
+ _mxc_nand_enable_hwecc(mtd, 1);
return 0;
}
static int mxc_nand_read_page_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
uint8_t *buf,
+ int oob_required,
int page)
{
struct mxc_nand_host *host = chip->priv;
uint8_t *oob = chip->oob_poi;
MTDDEBUG(MTD_DEBUG_LEVEL1, "Reading page %u to buf %p oob %p\n",
- host->page_addr, buf, oob);
+ page, buf, oob);
- /* first read out the data area and the available portion of OOB */
+ /* first read the data area and the available portion of OOB */
for (n = 0; eccsteps; n++, eccsteps--, p += eccsize) {
int stat;
/* Then switch ECC off and read the OOB area to get the ECC code */
_mxc_nand_enable_hwecc(mtd, 0);
- chip->cmdfunc(mtd, NAND_CMD_READOOB, mtd->writesize, host->page_addr);
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, mtd->writesize, page);
eccsteps = chip->ecc.steps;
oob = chip->oob_poi + chip->ecc.prepad;
for (n = 0; eccsteps; n++, eccsteps--, p += eccsize) {
return status & NAND_STATUS_FAIL ? -EIO : 0;
}
-static void mxc_nand_write_page_raw_syndrome(struct mtd_info *mtd,
+static int mxc_nand_write_page_raw_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
- const uint8_t *buf)
+ const uint8_t *buf,
+ int oob_required)
{
struct mxc_nand_host *host = chip->priv;
int eccsize = chip->ecc.size;
size = mtd->oobsize - (oob - chip->oob_poi);
if (size)
chip->write_buf(mtd, oob, size);
+ return 0;
}
-static void mxc_nand_write_page_syndrome(struct mtd_info *mtd,
+static int mxc_nand_write_page_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
- const uint8_t *buf)
+ const uint8_t *buf,
+ int oob_required)
{
struct mxc_nand_host *host = chip->priv;
int i, n, eccsize = chip->ecc.size;
i = mtd->oobsize - (oob - chip->oob_poi);
if (i)
chip->write_buf(mtd, oob, i);
+ return 0;
}
static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+ uint32_t ecc_status = readl(&host->regs->ecc_status_result);
int subpages = mtd->writesize / nand_chip->subpagesize;
int pg2blk_shift = nand_chip->phys_erase_shift -
nand_chip->page_shift;
#define mxc_nand_write_page_syndrome NULL
#define mxc_nand_write_page_raw_syndrome NULL
#define mxc_nand_write_oob_syndrome NULL
-#define mxc_nfc_11_nand_correct_data NULL
static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
u_char *read_ecc, u_char *calc_ecc)
* additional correction. 2-Bit errors cannot be corrected by
* HW ECC, so we need to return failure
*/
- uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+ uint16_t ecc_status = readnfc(&host->regs->ecc_status_result);
if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
MTDDEBUG(MTD_DEBUG_LEVEL0,
}
#endif
-
-
static int mxc_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
u_char *ecc_code)
{
/*
* before sending SEQIN command for partial write,
* we need read one page out. FSL NFC does not support
- * partial write. It alway send out 512+ecc+512+ecc ...
+ * partial write. It always sends out 512+ecc+512+ecc
* for large page nand flash. But for small page nand
* flash, it does support SPARE ONLY operation.
*/
case NAND_CMD_PAGEPROG:
send_prog_page(host, 0, host->spare_only);
- if (host->pagesize_2k && !is_mxc_nfc_11()) {
- /* data in 4 areas datas */
+ if (host->pagesize_2k && is_mxc_nfc_1()) {
+ /* data in 4 areas */
send_prog_page(host, 1, host->spare_only);
send_prog_page(host, 2, host->spare_only);
send_prog_page(host, 3, host->spare_only);
if (column != -1) {
/*
* MXC NANDFC can only perform full page+spare or
- * spare-only read/write. When the upper layers
- * layers perform a read/write buf operation,
- * we will used the saved column adress to index into
- * the full page.
+ * spare-only read/write. When the upper layers perform
+ * a read/write buffer operation, we will use the saved
+ * column address to index into the full page.
*/
send_addr(host, 0);
if (host->pagesize_2k)
send_cmd(host, NAND_CMD_READSTART);
/* read for each AREA */
send_read_page(host, 0, host->spare_only);
- if (!is_mxc_nfc_11()) {
+ if (is_mxc_nfc_1()) {
send_read_page(host, 1, host->spare_only);
send_read_page(host, 2, host->spare_only);
send_read_page(host, 3, host->spare_only);
}
}
-#ifdef MXC_NFC_V1_1
-static void mxc_setup_config1(void)
-{
- uint16_t tmp;
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+
+static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
+static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 0,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = 4,
+ .pattern = bbt_pattern,
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 0,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = 4,
+ .pattern = mirror_pattern,
+};
- tmp = readw(&host->regs->nfc_config1);
- tmp |= NFC_ONE_CYCLE;
- tmp |= NFC_4_8N_ECC;
- writew(tmp, &host->regs->nfc_config1);
- if (host->pagesize_2k)
- writew(64/2, &host->regs->nfc_spare_area_size);
- else
- writew(16/2, &host->regs->nfc_spare_area_size);
-}
-#else
-#define mxc_setup_config1()
#endif
int board_nand_init(struct nand_chip *this)
{
struct mtd_info *mtd;
- uint16_t tmp;
- int err = 0;
+#if defined(MXC_NFC_V2_1) || defined(MXC_NFC_V3_2)
+ uint32_t tmp;
+#endif
+
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ this->bbt_options |= NAND_BBT_USE_FLASH;
+ this->bbt_td = &bbt_main_descr;
+ this->bbt_md = &bbt_mirror_descr;
+#endif
/* structures must be linked */
mtd = &host->mtd;
this->read_buf = mxc_nand_read_buf;
this->verify_buf = mxc_nand_verify_buf;
- host->regs = (struct nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
+ host->regs = (struct mxc_nand_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
+#ifdef MXC_NFC_V3_2
+ host->ip_regs =
+ (struct mxc_nand_ip_regs __iomem *)CONFIG_MXC_NAND_IP_REGS_BASE;
+#endif
host->clk_act = 1;
#ifdef CONFIG_MXC_NAND_HWECC
this->ecc.calculate = mxc_nand_calculate_ecc;
this->ecc.hwctl = mxc_nand_enable_hwecc;
this->ecc.correct = mxc_nand_correct_data;
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21() || is_mxc_nfc_32()) {
this->ecc.mode = NAND_ECC_HW_SYNDROME;
this->ecc.read_page = mxc_nand_read_page_syndrome;
this->ecc.read_page_raw = mxc_nand_read_page_raw_syndrome;
this->ecc.mode = NAND_ECC_HW;
}
+ if (this->ecc.mode == NAND_ECC_HW) {
+ if (is_mxc_nfc_1())
+ this->ecc.strength = 1;
+ else
+ this->ecc.strength = 4;
+ }
+
host->pagesize_2k = 0;
this->ecc.size = 512;
- tmp = readw(&host->regs->nfc_config1);
- tmp |= NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ _mxc_nand_enable_hwecc(mtd, 1);
#else
this->ecc.layout = &nand_soft_eccoob;
this->ecc.mode = NAND_ECC_SOFT;
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ _mxc_nand_enable_hwecc(mtd, 0);
#endif
/* Reset NAND */
this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ /* NAND bus width determines access functions used by upper layer */
+ if (is_16bit_nand())
+ this->options |= NAND_BUSWIDTH_16;
+
+#ifdef CONFIG_SYS_NAND_LARGEPAGE
+ host->pagesize_2k = 1;
+ this->ecc.layout = &nand_hw_eccoob2k;
+#else
+ host->pagesize_2k = 0;
+ this->ecc.layout = &nand_hw_eccoob;
+#endif
+
+#if defined(MXC_NFC_V1) || defined(MXC_NFC_V2_1)
+#ifdef MXC_NFC_V2_1
+ tmp = readnfc(&host->regs->config1);
+ tmp |= NFC_V2_CONFIG1_ONE_CYCLE;
+ tmp |= NFC_V2_CONFIG1_ECC_MODE_4;
+ writenfc(tmp, &host->regs->config1);
+ if (host->pagesize_2k)
+ writenfc(64/2, &host->regs->spare_area_size);
+ else
+ writenfc(16/2, &host->regs->spare_area_size);
+#endif
+
/*
* preset operation
* Unlock the internal RAM Buffer
*/
- writew(0x2, &host->regs->nfc_config);
+ writenfc(0x2, &host->regs->config);
/* Blocks to be unlocked */
- writew(0x0, &host->regs->nfc_unlockstart_blkaddr);
- writew(0x4000, &host->regs->nfc_unlockend_blkaddr);
+ writenfc(0x0, &host->regs->unlockstart_blkaddr);
+ /* Originally (Freescale LTIB 2.6.21) 0x4000 was written to the
+ * unlockend_blkaddr, but the magic 0x4000 does not always work
+ * when writing more than some 32 megabytes (on 2k page nands)
+ * However 0xFFFF doesn't seem to have this kind
+ * of limitation (tried it back and forth several times).
+ * The linux kernel driver sets this to 0xFFFF for the v2 controller
+ * only, but probably this was not tested there for v1.
+ * The very same limitation seems to apply to this kernel driver.
+ * This might be NAND chip specific and the i.MX31 datasheet is
+ * extremely vague about the semantics of this register.
+ */
+ writenfc(0xFFFF, &host->regs->unlockend_blkaddr);
/* Unlock Block Command for given address range */
- writew(0x4, &host->regs->nfc_wrprot);
+ writenfc(0x4, &host->regs->wrprot);
+#elif defined(MXC_NFC_V3_2)
+ writenfc(NFC_V3_CONFIG1_RBA(0), &host->regs->config1);
+ writenfc(NFC_V3_IPC_CREQ, &host->ip_regs->ipc);
- /* NAND bus width determines access funtions used by upper layer */
- if (is_16bit_nand())
- this->options |= NAND_BUSWIDTH_16;
+ /* Unlock the internal RAM Buffer */
+ writenfc(NFC_V3_WRPROT_BLS_UNLOCK | NFC_V3_WRPROT_UNLOCK,
+ &host->ip_regs->wrprot);
-#ifdef CONFIG_SYS_NAND_LARGEPAGE
- host->pagesize_2k = 1;
- this->ecc.layout = &nand_hw_eccoob2k;
-#else
- host->pagesize_2k = 0;
- this->ecc.layout = &nand_hw_eccoob;
+ /* Blocks to be unlocked */
+ for (tmp = 0; tmp < CONFIG_SYS_NAND_MAX_CHIPS; tmp++)
+ writenfc(0x0 | 0xFFFF << 16,
+ &host->ip_regs->wrprot_unlock_blkaddr[tmp]);
+
+ writenfc(0, &host->ip_regs->ipc);
+
+ tmp = readnfc(&host->ip_regs->config2);
+ tmp &= ~(NFC_V3_CONFIG2_SPAS_MASK | NFC_V3_CONFIG2_EDC_MASK |
+ NFC_V3_CONFIG2_ECC_MODE_8 | NFC_V3_CONFIG2_PS_MASK);
+ tmp |= NFC_V3_CONFIG2_ONE_CYCLE;
+
+ if (host->pagesize_2k) {
+ tmp |= NFC_V3_CONFIG2_SPAS(64/2);
+ tmp |= NFC_V3_CONFIG2_PS_2048;
+ } else {
+ tmp |= NFC_V3_CONFIG2_SPAS(16/2);
+ tmp |= NFC_V3_CONFIG2_PS_512;
+ }
+
+ writenfc(tmp, &host->ip_regs->config2);
+
+ tmp = NFC_V3_CONFIG3_NUM_OF_DEVS(0) |
+ NFC_V3_CONFIG3_NO_SDMA |
+ NFC_V3_CONFIG3_RBB_MODE |
+ NFC_V3_CONFIG3_SBB(6) | /* Reset default */
+ NFC_V3_CONFIG3_ADD_OP(0);
+
+ if (!(this->options & NAND_BUSWIDTH_16))
+ tmp |= NFC_V3_CONFIG3_FW8;
+
+ writenfc(tmp, &host->ip_regs->config3);
+
+ writenfc(0, &host->ip_regs->delay_line);
#endif
- mxc_setup_config1();
- return err;
+
+ return 0;
}
projects / karo-tx-uboot.git / blobdiff