These changes are tested with DM9000{A,EP,E} together
with a 200MHz Atmel AT91SAM92161 core
-TODO: Homerun NIC and longrun NIC are not functional, only internal at the
- moment.
+TODO: external MII is not functional, only internal at the moment.
*/
#include <common.h>
/* Board/System/Debug information/definition ---------------- */
-#define DM9801_NOISE_FLOOR 0x08
-#define DM9802_NOISE_FLOOR 0x05
-
/* #define CONFIG_DM9000_DEBUG */
#ifdef CONFIG_DM9000_DEBUG
#define DM9000_DMP_PACKET(func,packet,length)
#endif
-enum DM9000_PHY_mode { DM9000_10MHD = 0, DM9000_100MHD =
- 1, DM9000_10MFD = 4, DM9000_100MFD = 5, DM9000_AUTO =
- 8, DM9000_1M_HPNA = 0x10
-};
-enum DM9000_NIC_TYPE { FASTETHER_NIC = 0, HOMERUN_NIC = 1, LONGRUN_NIC = 2
-};
-
/* Structure/enum declaration ------------------------------- */
typedef struct board_info {
u32 runt_length_counter; /* counter: RX length < 64byte */
u16 dbug_cnt;
u8 phy_addr;
u8 device_wait_reset; /* device state */
- u8 nic_type; /* NIC type */
unsigned char srom[128];
void (*outblk)(volatile void *data_ptr, int count);
void (*inblk)(void *data_ptr, int count);
} board_info_t;
static board_info_t dm9000_info;
-/* For module input parameter */
-static int media_mode = DM9000_AUTO;
-static u8 nfloor = 0;
-
/* function declaration ------------------------------------- */
int eth_init(bd_t * bd);
int eth_send(volatile void *, int);
DM9000_outb(DM9000_MRCMD, DM9000_IO);
tmpdata = DM9000_inl(DM9000_DATA);
- *RxStatus = tmpdata;
- *RxLen = tmpdata >> 16;
+ *RxStatus = __le16_to_cpu(tmpdata);
+ *RxLen = __le16_to_cpu(tmpdata >> 16);
}
static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
- *RxStatus = DM9000_inw(DM9000_DATA);
- *RxLen = DM9000_inw(DM9000_DATA);
+ *RxStatus = __le16_to_cpu(DM9000_inw(DM9000_DATA));
+ *RxLen = __le16_to_cpu(DM9000_inw(DM9000_DATA));
}
static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
- *RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
- *RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
+ *RxStatus =
+ __le16_to_cpu(DM9000_inb(DM9000_DATA) +
+ (DM9000_inb(DM9000_DATA) << 8));
+ *RxLen =
+ __le16_to_cpu(DM9000_inb(DM9000_DATA) +
+ (DM9000_inb(DM9000_DATA) << 8));
}
/*
}
}
-/* Set PHY operationg mode
-*/
-static void
-set_PHY_mode(void)
-{
- u16 phy_reg4 = 0x01e1, phy_reg0 = 0x1000;
- if (!(media_mode & DM9000_AUTO)) {
- switch (media_mode) {
- case DM9000_10MHD:
- phy_reg4 = 0x21;
- phy_reg0 = 0x0000;
- break;
- case DM9000_10MFD:
- phy_reg4 = 0x41;
- phy_reg0 = 0x1100;
- break;
- case DM9000_100MHD:
- phy_reg4 = 0x81;
- phy_reg0 = 0x2000;
- break;
- case DM9000_100MFD:
- phy_reg4 = 0x101;
- phy_reg0 = 0x3100;
- break;
- }
- phy_write(4, phy_reg4); /* Set PHY media mode */
- phy_write(0, phy_reg0); /* Tmp */
- }
- DM9000_iow(DM9000_GPCR, 0x01); /* Let GPIO0 output */
- DM9000_iow(DM9000_GPR, 0x00); /* Enable PHY */
-}
-
-/*
- Init HomeRun DM9801
-*/
-static void
-program_dm9801(u16 HPNA_rev)
-{
- __u16 reg16, reg17, reg24, reg25;
- if (!nfloor)
- nfloor = DM9801_NOISE_FLOOR;
- reg16 = phy_read(16);
- reg17 = phy_read(17);
- reg24 = phy_read(24);
- reg25 = phy_read(25);
- switch (HPNA_rev) {
- case 0xb900: /* DM9801 E3 */
- reg16 |= 0x1000;
- reg25 = ((reg24 + nfloor) & 0x00ff) | 0xf000;
- break;
- case 0xb901: /* DM9801 E4 */
- reg25 = ((reg24 + nfloor) & 0x00ff) | 0xc200;
- reg17 = (reg17 & 0xfff0) + nfloor + 3;
- break;
- case 0xb902: /* DM9801 E5 */
- case 0xb903: /* DM9801 E6 */
- default:
- reg16 |= 0x1000;
- reg25 = ((reg24 + nfloor - 3) & 0x00ff) | 0xc200;
- reg17 = (reg17 & 0xfff0) + nfloor;
- }
- phy_write(16, reg16);
- phy_write(17, reg17);
- phy_write(25, reg25);
-}
-
-/*
- Init LongRun DM9802
-*/
-static void
-program_dm9802(void)
-{
- __u16 reg25;
- if (!nfloor)
- nfloor = DM9802_NOISE_FLOOR;
- reg25 = phy_read(25);
- reg25 = (reg25 & 0xff00) + nfloor;
- phy_write(25, reg25);
-}
-
-/* Identify NIC type
-*/
-static void
-identify_nic(void)
-{
- struct board_info *db = &dm9000_info;
- u16 phy_reg3;
- DM9000_iow(DM9000_NCR, NCR_EXT_PHY);
- phy_reg3 = phy_read(3);
- switch (phy_reg3 & 0xfff0) {
- case 0xb900:
- if (phy_read(31) == 0x4404) {
- db->nic_type = HOMERUN_NIC;
- program_dm9801(phy_reg3);
- DM9000_DBG("found homerun NIC\n");
- } else {
- db->nic_type = LONGRUN_NIC;
- DM9000_DBG("found longrun NIC\n");
- program_dm9802();
- }
- break;
- default:
- db->nic_type = FASTETHER_NIC;
- break;
- }
- DM9000_iow(DM9000_NCR, 0);
-}
-
/* General Purpose dm9000 reset routine */
static void
dm9000_reset(void)
/* Reset DM9000,
see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
- /* DEBUG: Make all GPIO pins outputs */
- DM9000_iow(DM9000_GPCR, 0x0F);
+ /* DEBUG: Make all GPIO0 outputs, all others inputs */
+ DM9000_iow(DM9000_GPCR, GPCR_GPIO0_OUT);
/* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
DM9000_iow(DM9000_GPR, 0);
/* Step 2: Software reset */
- DM9000_iow(DM9000_NCR, 3);
+ DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST));
do {
DM9000_DBG("resetting the DM9000, 1st reset\n");
} while (DM9000_ior(DM9000_NCR) & 1);
DM9000_iow(DM9000_NCR, 0);
- DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */
+ DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); /* Issue a second reset */
do {
DM9000_DBG("resetting the DM9000, 2nd reset\n");
/* RESET device */
dm9000_reset();
- dm9000_probe();
+
+ if (dm9000_probe() < 0)
+ return -1;
/* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */
io_mode = DM9000_ior(DM9000_ISR) >> 6;
break;
}
- /* NIC Type: FASTETHER, HOMERUN, LONGRUN */
- identify_nic();
-
- /* GPIO0 on pre-activate PHY */
- DM9000_iow(DM9000_GPR, 0x00); /*REG_1F bit0 activate phyxcer */
-
- /* Set PHY */
- set_PHY_mode();
-
- /* Program operating register, only intern phy supported by now */
+ /* Program operating register, only internal phy supported */
DM9000_iow(DM9000_NCR, 0x0);
/* TX Polling clear */
DM9000_iow(DM9000_TCR, 0);
/* Less 3Kb, 200us */
- DM9000_iow(DM9000_BPTR, 0x3f);
+ DM9000_iow(DM9000_BPTR, BPTR_BPHW(3) | BPTR_JPT_600US);
/* Flow Control : High/Low Water */
DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8));
/* SH FIXME: This looks strange! Flow Control */
/* clear TX status */
DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END);
/* Clear interrupt status */
- DM9000_iow(DM9000_ISR, 0x0f);
+ DM9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS);
/* Set Node address */
-#ifndef CONFIG_AT91SAM9261EK
+#if !defined(CONFIG_AT91SAM9261EK)
for (i = 0; i < 6; i++)
((u16 *) bd->bi_enetaddr)[i] = read_srom_word(i);
#endif
printf("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", bd->bi_enetaddr[0],
bd->bi_enetaddr[1], bd->bi_enetaddr[2], bd->bi_enetaddr[3],
bd->bi_enetaddr[4], bd->bi_enetaddr[5]);
- for (i = 0, oft = 0x10; i < 6; i++, oft++)
+
+ /* fill device MAC address registers */
+ for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++)
DM9000_iow(oft, bd->bi_enetaddr[i]);
for (i = 0, oft = 0x16; i < 8; i++, oft++)
DM9000_iow(oft, 0xff);
DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
/* wait for end of transmission */
- tmo = get_timer(0) + 5 * CFG_HZ;
+ tmo = get_timer(0) + 5 * CONFIG_SYS_HZ;
while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) ||
!(DM9000_ior(DM9000_ISR) & IMR_PTM) ) {
if (get_timer(0) >= tmo) {
projects / karo-tx-uboot.git / blobdiff