#define CONFIG_BC3450_FP 1 /* + enable FP O/P */
#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* AT-PS/2 Multiplexer
# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
-# define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */
# define CONFIG_BOARD_EARLY_INIT_R
#endif /* CONFIG_BC3450_PS2 */
# define CONFIG_PCI 1
# define CONFIG_PCI_PNP 1
/* #define CONFIG_PCI_SCAN_SHOW 1 */
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_NET_MULTI 1
/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#ifdef CONFIG_PCI
-# define ADD_PCI_CMD CFG_CMD_PCI
-#else
-# define ADD_PCI_CMD 0
-#endif
-
/*
* Video console
*/
# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */
# define CONFIG_VIDEO_SW_CURSOR
# define CONFIG_SPLASH_SCREEN
-# define CFG_CONSOLE_IS_IN_ENV
-
-#ifdef CONFIG_VIDEO
-# define ADD_BMP_CMD CFG_CMD_BMP
-#else
-# define ADD_BMP_CMD 0
-#endif
+# define CONFIG_SYS_CONSOLE_IS_IN_ENV
/*
* Partitions
*/
#ifdef CONFIG_BC3450_USB
# define CONFIG_USB_OHCI
-# define ADD_USB_CMD CFG_CMD_USB
# define CONFIG_USB_STORAGE
-#else /* !CONFIG_BC3450_USB */
-# define ADD_USB_CMD 0
#endif /* CONFIG_BC3450_USB */
/*
* POST support
*/
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_I2C)
#ifdef CONFIG_POST
-# define CFG_CMD_POST_DIAG CFG_CMD_DIAG
/* preserve space for the post_word at end of on-chip SRAM */
# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#else
-# define CFG_CMD_POST_DIAG 0
#endif /* CONFIG_POST */
-/*
- * IDE
- */
-#ifdef CONFIG_BC3450_IDE
-# define ADD_IDE_CMD CFG_CMD_IDE
-#else
-# define ADD_IDE_CMD 0
-#endif /* CONFIG_BC3450_IDE */
/*
- * Filesystem support
+ * BOOTP options
*/
-#if defined (CONFIG_BC3450_IDE) || defined (CONFIG_BC3450_USB)
-#ifdef CONFIG_FAT
-# define ADD_FAT_CMD CFG_CMD_FAT
-#else
-# define ADD_FAT_CMD 0
-#endif /* CONFIG_FAT */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
-#ifdef CONFIG_EXT2
-# define ADD_EXT2_CMD CFG_CMD_EXT2
-#else
-# define ADD_EXT2_CMD 0
-#endif /* CONFIG_EXT2 */
-#endif /* CONFIG_BC3450_IDE / _USB */
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_BMP_CMD | \
- ADD_IDE_CMD | \
- ADD_FAT_CMD | \
- ADD_EXT2_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_NFS | \
- CFG_CMD_PING | \
- CFG_CMD_POST_DIAG | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SNTP | \
- CFG_CMD_BSP)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_BSP
+
+#ifdef CONFIG_VIDEO
+ #define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_BC3450_IDE
+ #define CONFIG_CMD_IDE
+#endif
+
+#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB)
+ #ifdef CONFIG_FAT
+ #define CONFIG_CMD_FAT
+ #endif
+
+ #ifdef CONFIG_EXT2
+ #define CONFIG_CMD_EXT2
+ #endif
+#endif
+
+#ifdef CONFIG_BC3450_USB
+ #define CONFIG_CMD_USB
+#endif
+
+#ifdef CONFIG_PCI
+ #define CONFIG_CMD_PCI
+#endif
+
+#ifdef CONFIG_POST
+ #define CONFIG_CMD_DIAG
+#endif
+
#define CONFIG_TIMESTAMP /* display image timestamps */
#if (TEXT_BASE == 0xFC000000) /* Boot low */
-# define CFG_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT 1
#endif
/*
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo;"
#undef CONFIG_BOOTARGS
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet
- * hasn't been tested with a IPB Bus Clock of 66 MHz.
+ * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#if defined(CFG_IPBSPEED_133)
-# define CFG_PCISPEED_66 /* define for 66MHz speed */
+#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
+# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #2 */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
/*
* I2C clock frequency
* Please notice, that the resulting clock frequency could differ from the
* configured value. This is because the I2C clock is derived from system
* clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CFG_I2C_SPEED. However the calculated
+ * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
* approximation allways lies below the configured value, never above.
*/
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration for I²C EEPROM M24C32
*
* The TQM5200 module may hold an EEPROM at address 0x50.
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
/*
* RTC configuration
*/
#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231)
# define CONFIG_RTC_M41T11 1
-# define CFG_I2C_RTC_ADDR 0x68
+# define CONFIG_SYS_I2C_RTC_ADDR 0x68
#else
# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */
# define CONFIG_BOARD_EARLY_INIT_R
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
+#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */
/* use CFI flash driver if no module variant is spezified */
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
-#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
-
-#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
-#endif /* CFG_LOWBOOT */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
+
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=TQM5200-0"
#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
"1408k(kernel)," \
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x10000
-#define CFG_ENV_SECT_SIZE 0x20000
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use ON-Chip SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
-# define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+# define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
#else
-# define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
+# define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
#endif /*CONFIG_POST*/
-#define CFG_GBL_DATA_SIZE 128 /* Bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*
- * Define CONFIG_FEC10MBIT to force FEC at 10MBIT
+ * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT
*/
#define CONFIG_MPC5xxx_FEC 1
-#undef CONFIG_FEC_10MBIT
+#define CONFIG_MPC5xxx_FEC_MII100
+#undef CONFIG_MPC5xxx_MII10
#define CONFIG_PHY_ADDR 0x00
/*
* I2C: CAN1 / I²C2 [0x bxxxxxxx]
*/
#ifdef CONFIG_BC3450_AC97
-# define CFG_GPS_PORT_CONFIG 0xb1502124
+# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124
#else /* PSC2=UART2 */
-# define CFG_GPS_PORT_CONFIG 0xb1502144
+# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max no of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Arg. Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max no of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */
-#define CFG_ALT_MEMTEST /* Enable an alternative, */
+#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */
/* more extensive mem test */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* dec freq: 1ms ticks */
+#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
/*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
*/
#define CONFIG_LOOPW
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
-# define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-# define CFG_HID0_FINAL HID0_ICE
+# define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+# define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
-# define CFG_HID0_INIT 0
-# define CFG_HID0_FINAL 0
+# define CONFIG_SYS_HID0_INIT 0
+# define CONFIG_SYS_HID0_FINAL 0
#endif
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
-# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
+# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
-# define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
#endif
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
/* automatic configuration of chip selects */
#ifdef CONFIG_TQM5200
* for SDRAM autosizing.
*/
#ifdef CONFIG_TQM5200
-# define CFG_CS2_START 0xE5000000
-# define CFG_CS2_SIZE 0x100000 /* 1 MByte */
-# define CFG_CS2_CFG 0x0004D930
+# define CONFIG_SYS_CS2_START 0xE5000000
+# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
+# define CONFIG_SYS_CS2_CFG 0x0004D930
#endif /* CONFIG_TQM5200 */
/*
*/
#ifdef CONFIG_TQM5200
# define SM501_FB_BASE 0xE0000000
-# define CFG_CS1_START (SM501_FB_BASE)
-# define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
-# define CFG_CS1_CFG 0x8F48FF70
-# define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
+# define CONFIG_SYS_CS1_START (SM501_FB_BASE)
+# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
+# define CONFIG_SYS_CS1_CFG 0x8F48FF70
+# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
#endif /* CONFIG_TQM5200 */
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */
/* flash and SM501 */
-#define CFG_RESET_ADDRESS 0xff000000
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*
* USB stuff
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CONFIG_SYS_ATA_STRIDE 4
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff