* (C) Copyright 2005
* Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_VOM405 1 /* ...on a VOM405 board */
+#define CONFIG_SYS_TEXT_BASE 0xFFFC8000
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_PPC4xx_EMAC
-#define CONFIG_NET_MULTI 1
#undef CONFIG_HAS_ETH1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_CONS_INDEX 2 /* Use UART1 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD 691200
-#define CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (~(TEXT_BASE) + 1)
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
*/
-#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
-#define CONFIG_SYS_GPIO0_OSRH 0x40000500 /* 0 ... 15 */
-#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* 16 ... 31 */
-#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */
-#define CONFIG_SYS_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 0 ... 15 */
-#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_OSRL 0x40000500 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */
#define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 8) /* GPIO8 */
#define CONFIG_SYS_PLD_RESET (0x80000000 >> 12) /* GPIO12 */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
/*
* Default speed selection (cpu_plb_opb_ebc) in mhz.
* This value will be set if iic boot eprom is disabled.
projects / karo-tx-uboot.git / blobdiff