#define CONFIG_MISC_INIT_R /* initialize the icache L1 */
#define CONFIG_BOARD_EARLY_INIT_F
-#define CFG_BOARD_NAME "DB64460"
+#define CONFIG_SYS_BOARD_NAME "DB64460"
#define CONFIG_IDENT_STRING "Marvell DB64460 (1.0)"
-/*#define CFG_HUSH_PARSER */
-#undef CFG_HUSH_PARSER
+/*#define CONFIG_SYS_HUSH_PARSER */
+#undef CONFIG_SYS_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/*
* The following defines let you select what serial you want to use
*
* what to do:
* to use the DUART, undef CONFIG_MPSC. If you have hacked a serial
- * cable onto the second DUART channel, change the CFG_DUART port from 1
+ * cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1
* to 0 below.
*
* to use the MPSC, #define CONFIG_MPSC. If you have wired up another
#undef CONFIG_BOOTARGS
-/*#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" */
+/*#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" */
/* ronen - autoboot using tftp */
#if (CONFIG_BOOTDELAY >= 0)
/* --------------------------------------------------------------------------------------------------------------- */
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_ALTIVEC /* undef to disable */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
- CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor1"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
* Note: fake mtd_id's used, no linux mtd map file.
*/
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor1=db64460-1"
#define MTDPARTS_DEFAULT "mtdparts=db64460-1:-(jffs2)"
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_ASKENV \
- | CFG_CMD_I2C \
- | CFG_CMD_EEPROM \
- | CFG_CMD_CACHE \
- | CFG_CMD_JFFS2 \
- | CFG_CMD_PCI \
- | CFG_CMD_NET )
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+
/*
* Miscellaneous configurable options
*/
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_SPEED 40000 /* I2C speed default */
-
-/* #define CFG_GT_DUAL_CPU also for JTAG even with one cpu */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_SPEED 40000 /* I2C speed default */
+
+/* #define CONFIG_SYS_GT_DUAL_CPU also for JTAG even with one cpu */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-/*#define CFG_MEMTEST_START 0x00400000 memtest works on */
-/*#define CFG_MEMTEST_END 0x00C00000 4 ... 12 MB in DRAM */
-/*#define CFG_MEMTEST_END 0x07c00000 4 ... 124 MB in DRAM */
+/*#define CONFIG_SYS_MEMTEST_START 0x00400000 memtest works on */
+/*#define CONFIG_SYS_MEMTEST_END 0x00C00000 4 ... 12 MB in DRAM */
+/*#define CONFIG_SYS_MEMTEST_END 0x07c00000 4 ... 124 MB in DRAM */
/*
-#define CFG_DRAM_TEST
+#define CONFIG_SYS_DRAM_TEST
* DRAM tests
- * CFG_DRAM_TEST - enables the following tests.
+ * CONFIG_SYS_DRAM_TEST - enables the following tests.
*
- * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines
+ * CONFIG_SYS_DRAM_TEST_DATA - Enables test for shorted or open data lines
* Environment variable 'test_dram_data' must be
* set to 'y'.
- * CFG_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
+ * CONFIG_SYS_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
* addressable. Environment variable
* 'test_dram_address' must be set to 'y'.
- * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
+ * CONFIG_SYS_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
* This test takes about 6 minutes to test 64 MB.
* Environment variable 'test_dram_walk' must be
* set to 'y'.
*/
-#define CFG_DRAM_TEST
-#if defined(CFG_DRAM_TEST)
-#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
-/* #define CFG_MEMTEST_END 0x00C00000 4 ... 12 MB in DRAM */
-#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
-#define CFG_DRAM_TEST_DATA
-#define CFG_DRAM_TEST_ADDRESS
-#define CFG_DRAM_TEST_WALK
-#endif /* CFG_DRAM_TEST */
+#define CONFIG_SYS_DRAM_TEST
+#if defined(CONFIG_SYS_DRAM_TEST)
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
+/* #define CONFIG_SYS_MEMTEST_END 0x00C00000 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
+#define CONFIG_SYS_DRAM_TEST_DATA
+#define CONFIG_SYS_DRAM_TEST_ADDRESS
+#define CONFIG_SYS_DRAM_TEST_WALK
+#endif /* CONFIG_SYS_DRAM_TEST */
#undef CONFIG_DISPLAY_MEMMAP /* at the end of the bootprocess show the memory map */
-#undef CFG_DISPLAY_DIMM_SPD_CONTENT /* show SPD content during boot */
+#undef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT /* show SPD content during boot */
-#define CFG_LOAD_ADDR 0x00400000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x00400000 /* default load address */
-#define CFG_HZ 1000 /* decr freq: 1ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decr freq: 1ms ticks */
/*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CFG_BUS_HZ 133000000 /* 133 MHz (CPU = 5*Bus = 666MHz) */
-#define CFG_BUS_CLK CFG_BUS_HZ
+#define CONFIG_SYS_BUS_HZ 133000000 /* 133 MHz (CPU = 5*Bus = 666MHz) */
+#define CONFIG_SYS_BUS_CLK CONFIG_SYS_BUS_HZ
-#define CFG_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
-#define CFG_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 200MHZ -> 5.0 ns, 166MHZ -> 6.0, 133MHZ -> 7.50 ns */
+#define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
+#define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 200MHZ -> 5.0 ns, 166MHZ -> 6.0, 133MHZ -> 7.50 ns */
/*ronen - this is the Tclk (MV64460 core) */
-#define CFG_TCLK 133000000
+#define CONFIG_SYS_TCLK 133000000
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-#define CFG_750FX_HID0 0x8000c084
-#define CFG_750FX_HID1 0x54800000
-#define CFG_750FX_HID2 0x00000000
+#define CONFIG_SYS_750FX_HID0 0x8000c084
+#define CONFIG_SYS_750FX_HID1 0x54800000
+#define CONFIG_SYS_750FX_HID2 0x00000000
/*
* Low Level Configuration Settings
*/
/*
- * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS
* To an unused memory region. The stack will remain in cache until RAM
* is initialized
*/
-#define CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR 0x40000000 /* unused memory region */
-#define CFG_INIT_RAM_END 0x1000
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* unused memory region */
+#define CONFIG_SYS_INIT_RAM_END 0x1000
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define RELOCATE_INTERNAL_RAM_ADDR
#ifdef RELOCATE_INTERNAL_RAM_ADDR
- #define CFG_INTERNAL_RAM_ADDR 0xf8000000
+ #define CONFIG_SYS_INTERNAL_RAM_ADDR 0xf8000000
#endif
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* Dummies for BAT 4-7 */
-#define CFG_SDRAM1_BASE 0x10000000 /* each 256 MByte */
-#define CFG_SDRAM2_BASE 0x20000000
-#define CFG_SDRAM3_BASE 0x30000000
-#define CFG_SDRAM4_BASE 0x40000000
-#define CFG_FLASH_BASE 0xfff00000
+#define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */
+#define CONFIG_SYS_SDRAM2_BASE 0x20000000
+#define CONFIG_SYS_SDRAM3_BASE 0x30000000
+#define CONFIG_SYS_SDRAM4_BASE 0x40000000
+#define CONFIG_SYS_FLASH_BASE 0xfff00000
-#define CFG_DFL_BOOTCS_BASE 0xff800000
+#define CONFIG_SYS_DFL_BOOTCS_BASE 0xff800000
#define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS*/
#define BRIDGE_REG_BASE_BOOTM 0xfbe00000 /* this paramaters are used when booting the linux kernel */
#define UART_BASE_BOOTM 0xfbb00000 /* in order to be sync with the kernel parameters. */
#define PCI0_IO_BASE_BOOTM 0xfd000000
-#define CFG_RESET_ADDRESS 0xfff00100
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
+#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
/* areas to map different things with the GT in physical space */
-#define CFG_DRAM_BANKS 4
+#define CONFIG_SYS_DRAM_BANKS 4
/* What to put in the bats. */
-#define CFG_MISC_REGION_BASE 0xf0000000
+#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000
/* Peripheral Device section */
/* Data flash on external device module */
/* Boot flash on external device module */
/*******************************************************/
-#define CFG_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */
-#define CFG_DB64460_RESET_ADDR 0x14000000 /* After power on Reset the DB64460 is here */
+#define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */
+#define CONFIG_SYS_DB64460_RESET_ADDR 0x14000000 /* After power on Reset the DB64460 is here */
/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
-#define CFG_GT_REGS 0xf1000000 /* GT Registers will be mapped here */
-#define CFG_DEV_BASE 0xfc000000 /* GT Devices CS start here */
-
-#define CFG_DEV0_SPACE CFG_DEV_BASE /* DEV_CS0 device modul sram */
-#define CFG_DEV1_SPACE (CFG_DEV0_SPACE + CFG_DEV0_SIZE) /* DEV_CS1 device modul real time clock (rtc) */
-#define CFG_DEV2_SPACE (CFG_DEV1_SPACE + CFG_DEV1_SIZE) /* DEV_CS2 device modul doubel uart (duart) */
-#define CFG_DEV3_SPACE (CFG_DEV2_SPACE + CFG_DEV2_SIZE) /* DEV_CS3 device modul large flash */
-
-#define CFG_DEV0_SIZE _8M /* db64460 sram @ 0xfc00.0000 */
-#define CFG_DEV1_SIZE _8M /* db64460 rtc @ 0xfc80.0000 */
-#define CFG_DEV2_SIZE _16M /* db64460 duart @ 0xfd00.0000 */
-#define CFG_DEV3_SIZE _16M /* db64460 flash @ 0xfe00.0000 */
+#define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers will be mapped here */
+#define CONFIG_SYS_DEV_BASE 0xfc000000 /* GT Devices CS start here */
+
+#define CONFIG_SYS_DEV0_SPACE CONFIG_SYS_DEV_BASE /* DEV_CS0 device modul sram */
+#define CONFIG_SYS_DEV1_SPACE (CONFIG_SYS_DEV0_SPACE + CONFIG_SYS_DEV0_SIZE) /* DEV_CS1 device modul real time clock (rtc) */
+#define CONFIG_SYS_DEV2_SPACE (CONFIG_SYS_DEV1_SPACE + CONFIG_SYS_DEV1_SIZE) /* DEV_CS2 device modul doubel uart (duart) */
+#define CONFIG_SYS_DEV3_SPACE (CONFIG_SYS_DEV2_SPACE + CONFIG_SYS_DEV2_SIZE) /* DEV_CS3 device modul large flash */
+
+#define CONFIG_SYS_DEV0_SIZE _8M /* db64460 sram @ 0xfc00.0000 */
+#define CONFIG_SYS_DEV1_SIZE _8M /* db64460 rtc @ 0xfc80.0000 */
+#define CONFIG_SYS_DEV2_SIZE _16M /* db64460 duart @ 0xfd00.0000 */
+#define CONFIG_SYS_DEV3_SIZE _16M /* db64460 flash @ 0xfe00.0000 */
/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected by device width */
-#define CFG_DEV0_PAR 0x8FEFFFFF /* 32Bit sram */
-#define CFG_DEV1_PAR 0x8FCFFFFF /* 8Bit rtc */
-#define CFG_DEV2_PAR 0x8FCFFFFF /* 8Bit duart */
-#define CFG_8BIT_BOOT_PAR 0x8FCFFFFF /* 8Bit flash */
-#define CFG_32BIT_BOOT_PAR 0x8FEFFFFF /* 32Bit flash */
+#define CONFIG_SYS_DEV0_PAR 0x8FEFFFFF /* 32Bit sram */
+#define CONFIG_SYS_DEV1_PAR 0x8FCFFFFF /* 8Bit rtc */
+#define CONFIG_SYS_DEV2_PAR 0x8FCFFFFF /* 8Bit duart */
+#define CONFIG_SYS_8BIT_BOOT_PAR 0x8FCFFFFF /* 8Bit flash */
+#define CONFIG_SYS_32BIT_BOOT_PAR 0x8FEFFFFF /* 32Bit flash */
/* c 4 a 8 2 4 1 c */
/* 33 22|2222|22 22|111 1|11 11|1 1 | | */
/* ronen - update MPP Control MV64460*/
-#define CFG_MPP_CONTROL_0 0x02222222
-#define CFG_MPP_CONTROL_1 0x11333011
-#define CFG_MPP_CONTROL_2 0x40431111
-#define CFG_MPP_CONTROL_3 0x00000044
+#define CONFIG_SYS_MPP_CONTROL_0 0x02222222
+#define CONFIG_SYS_MPP_CONTROL_1 0x11333011
+#define CONFIG_SYS_MPP_CONTROL_2 0x40431111
+#define CONFIG_SYS_MPP_CONTROL_3 0x00000044
-/*# define CFG_SERIAL_PORT_MUX 0x00000102 0=hiZ 1=MPSC0 2=ETH 0 and 2 RMII */
+/*# define CONFIG_SYS_SERIAL_PORT_MUX 0x00000102 0=hiZ 1=MPSC0 2=ETH 0 and 2 RMII */
-# define CFG_GPP_LEVEL_CONTROL 0x2c600000 /* 1111 1001 0000 1111 1100 0000 0000 0000*/
+# define CONFIG_SYS_GPP_LEVEL_CONTROL 0x2c600000 /* 1111 1001 0000 1111 1100 0000 0000 0000*/
/* gpp[31] gpp[30] gpp[29] gpp[28] */
/* gpp[27] gpp[24]*/
/* gpp[19:14] */
/* setup new config_value for MV64460 DDR-RAM !! */
-# define CFG_SDRAM_CONFIG 0x58200400 /* 0x1400 copied from Dink32 bzw. VxWorks*/
+# define CONFIG_SYS_SDRAM_CONFIG 0x58200400 /* 0x1400 copied from Dink32 bzw. VxWorks*/
-#define CFG_DUART_IO CFG_DEV2_SPACE
-#define CFG_DUART_CHAN 1 /* channel to use for console */
-#define CFG_INIT_CHAN1
-#define CFG_INIT_CHAN2
+#define CONFIG_SYS_DUART_IO CONFIG_SYS_DEV2_SPACE
+#define CONFIG_SYS_DUART_CHAN 1 /* channel to use for console */
+#define CONFIG_SYS_INIT_CHAN1
+#define CONFIG_SYS_INIT_CHAN2
-#define SRAM_BASE CFG_DEV0_SPACE
+#define SRAM_BASE CONFIG_SYS_DEV0_SPACE
#define SRAM_SIZE 0x00100000 /* 1 MB of sram */
#define CONFIG_EEPRO100 /* ronen - Support for Intel 82557/82559/82559ER chips */
/* PCI MEMORY MAP section */
-#define CFG_PCI0_MEM_BASE 0x80000000
-#define CFG_PCI0_MEM_SIZE _128M
-#define CFG_PCI1_MEM_BASE 0x88000000
-#define CFG_PCI1_MEM_SIZE _128M
+#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI0_MEM_SIZE _128M
+#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000
+#define CONFIG_SYS_PCI1_MEM_SIZE _128M
-#define CFG_PCI0_0_MEM_SPACE (CFG_PCI0_MEM_BASE)
-#define CFG_PCI1_0_MEM_SPACE (CFG_PCI1_MEM_BASE)
+#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE)
+#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE)
/* PCI I/O MAP section */
-#define CFG_PCI0_IO_BASE 0xfa000000
-#define CFG_PCI0_IO_SIZE _16M
-#define CFG_PCI1_IO_BASE 0xfb000000
-#define CFG_PCI1_IO_SIZE _16M
+#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000
+#define CONFIG_SYS_PCI0_IO_SIZE _16M
+#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000
+#define CONFIG_SYS_PCI1_IO_SIZE _16M
-#define CFG_PCI0_IO_SPACE (CFG_PCI0_IO_BASE)
-#define CFG_PCI0_IO_SPACE_PCI (CFG_PCI0_IO_BASE) /* ronen we want phy=bus 0x00000000 */
-#define CFG_PCI1_IO_SPACE (CFG_PCI1_IO_BASE)
-#define CFG_PCI1_IO_SPACE_PCI (CFG_PCI1_IO_BASE) /* ronen we want phy=bus 0x00000000 */
+#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE)
+#define CONFIG_SYS_PCI0_IO_SPACE_PCI (CONFIG_SYS_PCI0_IO_BASE) /* ronen we want phy=bus 0x00000000 */
+#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE)
+#define CONFIG_SYS_PCI1_IO_SPACE_PCI (CONFIG_SYS_PCI1_IO_BASE) /* ronen we want phy=bus 0x00000000 */
#if defined (CONFIG_750CX)
-#define CFG_PCI_IDSEL 0x0
+#define CONFIG_SYS_PCI_IDSEL 0x0
#else
-#define CFG_PCI_IDSEL 0x30
+#define CONFIG_SYS_PCI_IDSEL 0x30
#endif
/*----------------------------------------------------------------------
* Initial BAT mappings
*/
/* SDRAM */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT0U CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* init ram */
-#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* PCI0, PCI1 in one BAT */
-#define CFG_IBAT2L BATL_NO_ACCESS
-#define CFG_IBAT2U CFG_DBAT2U
-#define CFG_DBAT2L (CFG_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
+#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* GT regs, bootrom, all the devices, PCI I/O */
-#define CFG_IBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
-#define CFG_IBAT3U (CFG_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
-#define CFG_DBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U CFG_IBAT3U
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
+#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* I2C addresses for the two DIMM SPD chips */
#define DIMM0_I2C_ADDR 0x56
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-#define CFG_EXTRA_FLASH_DEVICE DEVICE3 /* extra flash at device 3 */
-#define CFG_EXTRA_FLASH_WIDTH 4 /* 32 bit */
-#define CFG_BOOT_FLASH_WIDTH 1 /* 8 bit */
+#define CONFIG_SYS_EXTRA_FLASH_DEVICE DEVICE3 /* extra flash at device 3 */
+#define CONFIG_SYS_EXTRA_FLASH_WIDTH 4 /* 32 bit */
+#define CONFIG_SYS_BOOT_FLASH_WIDTH 1 /* 8 bit */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_LOCK_TOUT 500 /* Timeout for Flash Lock (in ms) */
-#define CFG_FLASH_CFI 1
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_LOCK_TOUT 500 /* Timeout for Flash Lock (in ms) */
+#define CONFIG_SYS_FLASH_CFI 1
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x10000
-#define CFG_ENV_ADDR 0xFFF78000 /* Marvell 8-Bit Bootflash last sector */
-/* #define CFG_ENV_ADDR (CFG_FLASH_BASE+CFG_MONITOR_LEN-CFG_ENV_SECT_SIZE) */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_ADDR 0xFFF78000 /* Marvell 8-Bit Bootflash last sector */
+/* #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_MONITOR_LEN-CONFIG_ENV_SECT_SIZE) */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* look in include/mpc74xx.h for the defines used here
*/
-#define CFG_L2
+#define CONFIG_SYS_L2
#if defined (CONFIG_750CX) || defined (CONFIG_750FX)
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_BOARD_ASM_INIT 1
+#define CONFIG_SYS_BOARD_ASM_INIT 1
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff