#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_ICECUBE 1 /* ... on IceCube board */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
-#define ADD_PCI_CMD CFG_CMD_PCI
#endif
-#define CFG_XLB_PIPELINING 1
+#define CONFIG_SYS_XLB_PIPELINING 1
#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1
#define CONFIG_EEPRO100 1
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#else /* MPC5100 */
-
+#else
#define CONFIG_MII 1
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
-
#endif
/* Partitions */
#define CONFIG_ISO_PARTITION
/* USB */
-#if 1
-#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
-#endif
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP | \
- ADD_PCI_CMD | \
- ADD_USB_CMD )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#endif
+
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CFG_LOWBOOT 1
-# define CFG_LOWBOOT16 1
+# define CONFIG_SYS_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT16 1
#endif
#if (TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
#if defined(CONFIG_LITE5200B)
-# error CFG_LOWBOOT08 is incompatible with the Lite5200B
+# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
#else
-# define CFG_LOWBOOT 1
-# define CFG_LOWBOOT08 1
+# define CONFIG_SYS_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT08 1
#endif
#endif
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
* IPB Bus clocking configuration.
*/
#if defined(CONFIG_LITE5200B)
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#else
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
#endif /* CONFIG_MPC5200 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
/*
* Flash configuration
*/
#if defined(CONFIG_LITE5200B)
-#define CFG_FLASH_BASE 0xFE000000
-#define CFG_FLASH_SIZE 0x01000000
-#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x01760000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#if defined(CFG_LOWBOOT08)
-# error CFG_LOWBOOT08 is incompatible with the Lite5200B
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 0x01000000
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#if defined(CONFIG_SYS_LOWBOOT08)
+# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
#endif
-#if defined(CFG_LOWBOOT16)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x01060000)
+#if defined(CONFIG_SYS_LOWBOOT16)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01060000)
#endif
-#endif /* CFG_LOWBOOT */
+#endif /* CONFIG_SYS_LOWBOOT */
#else /* !CONFIG_LITE5200B (IceCube)*/
-#define CFG_FLASH_BASE 0xFF000000
-#define CFG_FLASH_SIZE 0x01000000
-#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00740000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#if defined(CFG_LOWBOOT08)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000 + 0x00800000)
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 0x01000000
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00740000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#if defined(CONFIG_SYS_LOWBOOT08)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000 + 0x00800000)
#endif
-#if defined(CFG_LOWBOOT16)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000)
+#if defined(CONFIG_SYS_LOWBOOT16)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
#endif
-#endif /* CFG_LOWBOOT */
+#endif /* CONFIG_SYS_LOWBOOT */
#endif /* CONFIG_LITE5200B */
-#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */
#if defined(CONFIG_LITE5200B)
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_BANKS_LIST {CFG_CS1_START,CFG_CS0_START}
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS1_START,CONFIG_SYS_CS0_START}
#endif
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x10000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000
#if defined(CONFIG_LITE5200B)
-#define CFG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SECT_SIZE 0x20000
#else
-#define CFG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SECT_SIZE 0x10000
#endif
#define CONFIG_ENV_OVERWRITE 1
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
*/
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR 0x00
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_FEC_MII100 1
-#endif
/*
* GPIO configuration
*/
#ifdef CONFIG_MPC5200_DDR
-#define CFG_GPS_PORT_CONFIG 0x90000004
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x90000004
#else
-#define CFG_GPS_PORT_CONFIG 0x10000004
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
/*
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL 0
#endif
#if defined(CONFIG_LITE5200B)
-#define CFG_CS1_START CFG_FLASH_BASE
-#define CFG_CS1_SIZE CFG_FLASH_SIZE
-#define CFG_CS1_CFG 0x00047800
-#define CFG_CS0_START (CFG_FLASH_BASE + CFG_FLASH_SIZE)
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_START CFG_CS0_START
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG 0x00047800
+#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_CS1_CFG 0x00047800
+#define CONFIG_SYS_CS0_START (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE)
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_CS0_START
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG 0x00047800
#else /* IceCube aka Lite5200 */
#ifdef CONFIG_MPC5200_DDR
-#define CFG_BOOTCS_START (CFG_CS1_START + CFG_CS1_SIZE)
-#define CFG_BOOTCS_SIZE 0x00800000
-#define CFG_BOOTCS_CFG 0x00047801
-#define CFG_CS1_START CFG_FLASH_BASE
-#define CFG_CS1_SIZE 0x00800000
-#define CFG_CS1_CFG 0x00047800
+#define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS1_START + CONFIG_SYS_CS1_SIZE)
+#define CONFIG_SYS_BOOTCS_SIZE 0x00800000
+#define CONFIG_SYS_BOOTCS_CFG 0x00047801
+#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS1_SIZE 0x00800000
+#define CONFIG_SYS_CS1_CFG 0x00047800
#else /* !CONFIG_MPC5200_DDR */
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG 0x00047801
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG 0x00047801
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
#endif /* CONFIG_MPC5200_DDR */
#endif /*CONFIG_LITE5200B */
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-#define CFG_RESET_ADDRESS 0xff000000
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*-----------------------------------------------------------------------
* USB stuff
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CONFIG_SYS_ATA_STRIDE 4
#define CONFIG_ATAPI 1
projects / karo-tx-uboot.git / blobdiff