#define CONFIG_PCI
#define CONFIG_83XX_GENERIC_PCI
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is VSC switch
+ * TSEC2 is SoC TSEC
+ */
+#define CONFIG_VSC7385_ENET
+#define CONFIG_TSEC2
+
#ifdef CFG_66MHZ
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
#elif defined(CFG_33MHZ)
#define CFG_IMMR 0xE0000000
+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DEFAULT_IMMR CFG_IMMR
+#endif
+
#define CFG_MEMTEST_START 0x00001000
#define CFG_MEMTEST_END 0x07f00000
#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+/*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC1
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE 0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE 8192
+
+#endif
+
/*
* DDR Setup
*/
* seem to have the SPD connected to I2C.
*/
#define CFG_DDR_SIZE 128 /* MB */
-#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \
- | 0x00040000 /* TODO */ \
+#define CFG_DDR_CONFIG ( CSCONFIG_EN \
+ | 0x00010000 /* TODO */ \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
- /* 0x80840102 */
+ /* 0x80010102 */
#define CFG_DDR_TIMING_3 0x00000000
#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
/* 0x00220802 */
#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
- | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
- | (13 << TIMING_CFG1_REFREC_SHIFT ) \
+ | (10 << TIMING_CFG1_REFREC_SHIFT ) \
| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
- /* 0x3935d322 */
-#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
- | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ /* 0x3835a322 */
+#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | ( 5 << TIMING_CFG2_CPO_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
- | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
- /* 0x0f9048ca */ /* P9-45,may need tuning */
-#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
- | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
- /* 0x03200064 */
+ | ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x129048c6 */ /* P9-45,may need tuning */
+#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x05100500 */
#if defined(CONFIG_DDR_2T_TIMING)
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
- | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_2T_EN \
| SDRAM_CFG_DBW_32 )
#else
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
- | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_32_BE )
/* 0x43080000 */
#endif
#define CFG_SDRAM_CFG2 0x00401000;
/* set burst length to 8 for 32-bit data path */
-#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
- | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
- /* 0x44400232 */
+#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44480632 */
#define CFG_DDR_MODE_2 0x8000C000;
#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
* FLASH on the Local Bus
*/
#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
#define CFG_FLASH_SIZE 8 /* flash size in MB */
#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
+#define CFG_NOR_BR_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
-#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \
+#define CFG_NOR_OR_PRELIM ( 0xFF800000 /* 8 MByte */ \
| OR_GPCM_XACS \
| OR_GPCM_SCY_9 \
| OR_GPCM_EHTR \
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) && !defined(CONFIG_NAND_SPL)
#define CFG_RAMBOOT
#endif
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
*/
-#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */
+#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4
#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
-#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
+#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
+
+/* drivers/mtd/nand/nand.c */
+#ifdef CONFIG_NAND_SPL
+#define CFG_NAND_BASE 0xFFF00000
+#else
+#define CFG_NAND_BASE 0xE2800000
+#endif
-/* drivers/nand/nand.c */
-#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
#define CFG_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CFG_NAND_BLOCK_SIZE 16384
+
+#define CFG_NAND_U_BOOT_SIZE (512 << 10)
+#define CFG_NAND_U_BOOT_DST 0x00100000
+#define CFG_NAND_U_BOOT_START 0x00100100
+#define CFG_NAND_U_BOOT_OFFS 16384
+#define CFG_NAND_U_BOOT_RELOC 0x00010000
-#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
+#define CFG_NAND_BR_PRELIM ( CFG_NAND_BASE \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V ) /* valid */
-#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+#define CFG_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_TRLX \
| OR_FCM_EHTR )
/* 0xFFFF8396 */
+
+#ifdef CONFIG_NAND_U_BOOT
+#define CFG_BR0_PRELIM CFG_NAND_BR_PRELIM
+#define CFG_OR0_PRELIM CFG_NAND_OR_PRELIM
+#define CFG_BR1_PRELIM CFG_NOR_BR_PRELIM
+#define CFG_OR1_PRELIM CFG_NOR_OR_PRELIM
+#else
+#define CFG_BR0_PRELIM CFG_NOR_BR_PRELIM
+#define CFG_OR0_PRELIM CFG_NOR_OR_PRELIM
+#define CFG_BR1_PRELIM CFG_NAND_BR_PRELIM
+#define CFG_OR1_PRELIM CFG_NAND_OR_PRELIM
+#endif
+
#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CFG_NAND_LBLAWBAR_PRELIM CFG_LBLAWBAR1_PRELIM
+#define CFG_NAND_LBLAWAR_PRELIM CFG_LBLAWAR1_PRELIM
+
+/* local bus read write buffer mapping */
+#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
+#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
+#define CFG_LBLAWBAR3_PRELIM 0xFA000000
+#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+
+/* Vitesse 7385 */
+
#define CFG_VSC7385_BASE 0xF0000000
-#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
+#ifdef CONFIG_VSC7385_ENET
+
#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
-/* local bus read write buffer mapping */
-#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
-#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
-#define CFG_LBLAWBAR3_PRELIM 0xFA000000
-#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8313@0"
-#define OF_SOC "soc8313@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc8313@e0000000/serial@4500"
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* Serial Port
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_I2C_CMD_TREE
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
#define CFG_I2C2_OFFSET 0x3100
-/* TSEC */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
-#define CONFIG_NET_MULTI
-
/*
* General PCI
* Addresses are mapped 1-1.
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
/*
- * TSEC configuration
+ * TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
-#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_TSEC1 1
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII /* MII PHY management */
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
+#define CFG_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x1c
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0x1c
-#define TSEC2_PHY_ADDR 4
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
+#define CFG_TSEC2_OFFSET 0x25000
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC2_PHYIDX 0
+#endif
+
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC1"
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
+#if defined(CONFIG_NAND_U_BOOT)
+ #define CONFIG_ENV_IS_IN_NAND 1
+ #define CFG_ENV_OFFSET (512 * 1024)
+ #define CFG_ENV_SECT_SIZE CFG_NAND_BLOCK_SIZE
+ #define CFG_ENV_SIZE CFG_ENV_SECT_SIZE
+ #define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE
+ #define CFG_ENV_RANGE (CFG_ENV_SECT_SIZE * 4)
+ #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_RANGE)
+#elif !defined(CFG_RAMBOOT)
#define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
#define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
/* Address and size of Redundant Environment Sector */
#else
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_CMD_DATE
#define CONFIG_CMD_PCI
-#if defined(CFG_RAMBOOT)
+#if defined(CFG_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 16384
-#define CFG_CACHELINE_SIZE 32
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-
#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
#ifdef CFG_66MHZ
HRCWL_CSB_TO_CLKIN_2X1 |\
HRCWL_CORE_TO_CSB_2X1)
+#define CFG_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
+
#elif defined(CFG_33MHZ)
/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
HRCWL_CSB_TO_CLKIN_5X1 |\
HRCWL_CORE_TO_CSB_2X1)
+#define CFG_NS16550_CLK (CONFIG_83XX_CLKIN * 5)
+
#endif
-/* 0xa0606c00 */
-#define CFG_HRCW_HIGH (\
+#define CFG_HRCW_HIGH_BASE (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_RL_EXT_LEGACY |\
HRCWH_TSEC1M_IN_RGMII |\
HRCWH_TSEC2M_IN_RGMII |\
- HRCWH_BIG_ENDIAN |\
- HRCWH_LALE_NORMAL)
+ HRCWH_BIG_ENDIAN)
+
+#ifdef CONFIG_NAND_SPL
+#define CFG_HRCW_HIGH (CFG_HRCW_HIGH_BASE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_ROM_LOC_NAND_SP_8BIT |\
+ HRCWH_RL_EXT_NAND)
+#else
+#define CFG_HRCW_HIGH (CFG_HRCW_HIGH_BASE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY)
+#endif
/* System IO Config */
#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
#define CFG_HID2 HID2_HBE
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* DDR @ 0x00000000 */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ETHADDR 00:E0:0C:00:95:01
-#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8313erdb.dtb
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define MK_STR(x) XMK_STR(x)
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
"ethprime=TSEC1\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"console=ttyS0\0" \
"setbootargs=setenv bootargs " \
"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
- "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv rootdev /dev/nfs;" \
- "run setbootargs;" \
- "run setipargs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
projects / karo-tx-uboot.git / blobdiff