* if CLKIN is 66.66MHz, then
* CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_2X1 |\
HRCWL_SVCOD_DIV_2 |\
HRCWL_CSB_TO_CLKIN_2X1 |\
HRCWL_CORE_TO_CSB_3X1)
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
/*
* System IO Config
*/
-#define CFG_SICRH 0x00000000
-#define CFG_SICRL 0x00000000 /* 3.3V, no delay */
+#define CONFIG_SYS_SICRH 0x00000000
+#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
/*
* IMMR new address
*/
-#define CFG_IMMR 0xE0000000
+#define CONFIG_SYS_IMMR 0xE0000000
/*
* Arbiter Setup
*/
-#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
-#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
-#define CFG_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
/*
* DDR Setup
*/
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \
| DDRCDR_PZ_LOZ \
| DDRCDR_NZ_LOZ \
| DDRCDR_ODT \
* Manually set up DDR parameters
* consist of two chips HY5PS12621BFP-C4 from HYNIX
*/
-#define CFG_DDR_SIZE 128 /* MB */
-#define CFG_DDR_CS0_BNDS 0x00000007
-#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG ( CSCONFIG_EN \
| 0x00010000 /* ODT_WR to CSn */ \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
/* 0x80010102 */
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
/* 0x00220802 */
-#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
| ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
/* 0x39356222 */
-#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
| ( 4 << TIMING_CFG2_CPO_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
/* 0x121048c7 */
-#define CFG_DDR_INTERVAL ( ( 0x0360 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+#define CONFIG_SYS_DDR_INTERVAL ( ( 0x0360 << SDRAM_INTERVAL_REFINT_SHIFT ) \
| ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
/* 0x03600100 */
-#define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
+#define CONFIG_SYS_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_32_BE )
/* 0x43080000 */
-#define CFG_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
-#define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \
| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
/* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CFG_DDR_MODE2 0x00000000
+#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00040000 /* memtest region */
-#define CFG_MEMTEST_END 0x00140000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00140000
/*
* The reserved memory
*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
#endif
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
-#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
-#define CFG_LBC_LBCR 0x00040000
+#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LBC_LBCR 0x00040000
/*
* FLASH on the Local Bus
*/
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CFG_FLASH_SIZE 8 /* FLASH size is 8M */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
-#define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM ( CONFIG_SYS_FLASH_BASE /* Flash Base address */ \
| (2 << BR_PS_SHIFT) /* 16 bit port size */ \
| BR_V ) /* valid */
-#define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \
+#define CONFIG_SYS_OR0_PRELIM ( (~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_EHTR \
| OR_GPCM_EAD )
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 135 /* 127 64KB sectors and 8 8KB top sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 135 /* 127 64KB sectors and 8 8KB top sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
-#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */
-#define CFG_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
+#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_NAND_BASE \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V ) /* valid */
-#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+#define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_EHTR )
/* 0xFFFF8396 */
-#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
-#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* Pass open firmware flat tree */
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
-#define CFG_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* Board info - revision and where boot from
*/
-#define CFG_I2C_PCF8574A_ADDR 0x39
+#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
/*
* Config on-board RTC
*/
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI_MEM_BASE 0x80000000
-#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE
-#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_MMIO_BASE 0x90000000
-#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
-#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_IO_BASE 0x00000000
-#define CFG_PCI_IO_PHYS 0xE0300000
-#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
-
-#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE
-#define CFG_PCI_SLV_MEM_BUS 0x00000000
-#define CFG_PCI_SLV_MEM_SIZE 0x80000000
+#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
+#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
+#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
+#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
+
+#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
+#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
#define CONFIG_PCI
#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */
#define CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
* TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/*
* TSEC ethernet configuration
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
-#define CFG_SATA_MAX_DEVICE 2
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
-#define CFG_SATA1_OFFSET 0x18000
-#define CFG_SATA1 (CFG_IMMR + CFG_SATA1_OFFSET)
-#define CFG_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SYS_SATA1_OFFSET 0x18000
+#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
-#define CFG_SATA2_OFFSET 0x19000
-#define CFG_SATA2 (CFG_IMMR + CFG_SATA2_OFFSET)
-#define CFG_SATA2_FLAGS FLAGS_DMA
+#define CONFIG_SYS_SATA2_OFFSET 0x19000
+#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
#define CONFIG_CMD_DATE
#define CONFIG_CMD_PCI
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT1U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP)
-#define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U CFG_IBAT2U
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* Stack in dcache: cacheable, no memory coherence */
-#define CFG_IBAT3L (CFG_INIT_RAM_ADDR | BATL_PP_10)
-#define CFG_IBAT3U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* PCI MEM space: cacheable */
-#define CFG_IBAT4L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT4L CFG_IBAT4L
-#define CFG_DBAT4U CFG_IBAT4U
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT5L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
-
-#define CFG_IBAT6L 0
-#define CFG_IBAT6U 0
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
-
-#define CFG_IBAT7L 0
-#define CFG_IBAT7U 0
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+
+#define CONFIG_SYS_IBAT6L 0
+#define CONFIG_SYS_IBAT6U 0
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+
+#define CONFIG_SYS_IBAT7L 0
+#define CONFIG_SYS_IBAT7U 0
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* Internal Definitions
projects / karo-tx-uboot.git / blobdiff