i2c, fsl_i2c: switch to new multibus/multiadapter support

[karo-tx-uboot.git] / include / configs / MPC8540ADS.h

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 8b3aff8e0668dd7225ed2a68bbf301cf94493b35..25638ac4847f7f8ed48a1b4a4aff9867a96e8781 100644 (file)
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -52,6 +52,7 @@
 #endif
 
 #define CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
@@ -89,15 +90,8 @@
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xe0000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
@@ -256,7 +250,6 @@
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
 #ifdef  CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -267,13 +260,12 @@
 /*
  * I2C
  */
-#define CONFIG_FSL_I2C         /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C                /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-#define CONFIG_SYS_I2C_NOPROBES        {0x69}  /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET          0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED       400000
+#define CONFIG_SYS_FSL_I2C_SLAVE       0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET      0x3000
+#define CONFIG_SYS_I2C_NOPROBES                { {0, 0x69} }
 
 /* RapidIO MMU */
 #define CONFIG_SYS_RIO_MEM_VIRT        0xc0000000      /* base address */
@@ -296,7 +288,6 @@
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -316,10 +307,6 @@
 
 #if defined(CONFIG_TSEC_ENET)
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_TSEC1   1
 #define CONFIG_TSEC1_NAME      "TSEC0"
@@ -420,11 +407,11 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -449,8 +436,8 @@
 #define CONFIG_IPADDR    192.168.1.253
 
 #define CONFIG_HOSTNAME                unknown
-#define CONFIG_ROOTPATH                /nfsroot
-#define CONFIG_BOOTFILE                your.uImage
+#define CONFIG_ROOTPATH                "/nfsroot"
+#define CONFIG_BOOTFILE                "your.uImage"
 
 #define CONFIG_SERVERIP  192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1