rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH

[karo-tx-uboot.git] / include / configs / PM826.h

diff --git a/include/configs/PM826.h b/include/configs/PM826.h
index 88fdb51adef553924a89c326cd81454170ab6c8b..0782ff0c470bf557c6f148fe7d8e8a56ceefd644 100644 (file)
--- a/include/configs/PM826.h
+++ b/include/configs/PM826.h
@@ -43,13 +43,13 @@
 
 #define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds     */
 
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
 
 #undef CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND                                                     \
-       "bootp; "                                                               \
-       "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "     \
-       "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "   \
+       "bootp; "                                                               \
+       "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "     \
+       "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "   \
        "bootm"
 
 /* enable I2C and select the hardware/software driver */
@@ -103,8 +103,7 @@
  *   - CONFIG_NET_MULTI must be defined
  *
  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
  */
 #define        CONFIG_NET_MULTI
 #undef CONFIG_ETHER_NONE               /* define if ether on something else */
@@ -152,35 +151,36 @@
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled            */
 
-#define CONFIG_BOOTP_MASK      (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DOC
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
 
 #ifdef CONFIG_PCI
-#define CONFIG_COMMANDS               (CONFIG_CMD_DFL  | \
-                               CFG_CMD_BEDBUG  | \
-                               CFG_CMD_DATE    | \
-                               CFG_CMD_DHCP    | \
-                               CFG_CMD_DOC     | \
-                               CFG_CMD_EEPROM  | \
-                               CFG_CMD_I2C     | \
-                               CFG_CMD_NFS     | \
-                               CFG_CMD_PCI     | \
-                               CFG_CMD_SNTP    )
-#else  /* ! PCI */
-#define CONFIG_COMMANDS               (CONFIG_CMD_DFL  | \
-                               CFG_CMD_BEDBUG  | \
-                               CFG_CMD_DATE    | \
-                               CFG_CMD_DHCP    | \
-                               CFG_CMD_DOC     | \
-                               CFG_CMD_EEPROM  | \
-                               CFG_CMD_I2C     | \
-                               CFG_CMD_NFS     | \
-                               CFG_CMD_SNTP    )
-#endif /* CONFIG_PCI */
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-#define CFG_NAND_LEGACY
+#define CONFIG_CMD_PCI
+#endif
+
+
+#define CONFIG_NAND_LEGACY
 
 /*
  * Disk-On-Chip configuration
@@ -197,7 +197,7 @@
  */
 #define        CFG_LONGHELP                    /* undef to save memory         */
 #define        CFG_PROMPT      "=> "           /* Monitor Command Prompt       */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define        CFG_CBSIZE      1024            /* Console I/O Buffer Size      */
 #else
 #define        CFG_CBSIZE      256             /* Console I/O Buffer Size      */
@@ -257,13 +257,13 @@
 
 #if 0
 /* Start port with environment in flash; switch to EEPROM later */
-#define CFG_ENV_IS_IN_FLASH    1
+#define CONFIG_ENV_IS_IN_FLASH 1
 #define CFG_ENV_ADDR           (CFG_FLASH_BASE+0x40000)
 #define CFG_ENV_SIZE           0x40000
 #define CFG_ENV_SECT_SIZE      0x40000
 #else
 /* Final version: environment in EEPROM */
-#define CFG_ENV_IS_IN_EEPROM   1
+#define CONFIG_ENV_IS_IN_EEPROM        1
 #define CFG_I2C_EEPROM_ADDR    0x58
 #define CFG_I2C_EEPROM_ADDR_LEN        1
 #define CFG_EEPROM_PAGE_WRITE_BITS     4
@@ -345,7 +345,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #  define CFG_CACHELINE_SHIFT  5       /* log base 2 of the above value */
 #endif