Blackfin: move CONFIG_BFIN_CPU to board config.mk

[karo-tx-uboot.git] / include / configs / blackstamp.h

diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h
index 887f3fb3a348338c445f0f7bb9515ffb3c89e553..3f5c95917d00f3cb413106bcc25a331ff15c13f2 100644 (file)
--- a/include/configs/blackstamp.h
+++ b/include/configs/blackstamp.h
@@ -24,13 +24,13 @@
 /* CPU Options
  * Be sure to set the Silicon Revision Correctly
  */
-#define CONFIG_BFIN_CPU                bf532-0.5
 #define CONFIG_BFIN_BOOT_MODE  BFIN_BOOT_SPI_MASTER
 
 /*
  * Board settings
  */
-#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111        1
 #define CONFIG_SMC91111_BASE   0x20300300
 
 /* FLASH/ETHERNET uses the same address range
@@ -69,7 +69,7 @@
  * Network settings
  */
 
-#ifdef CONFIG_DRIVER_SMC91111
+#ifdef CONFIG_SMC91111
 #define CONFIG_IPADDR          192.168.0.15
 #define CONFIG_NETMASK         255.255.255.0
 #define CONFIG_GATEWAYIP       192.168.0.1
@@ -108,7 +108,7 @@
 
 #include <config_cmd_default.h>
 
-#ifdef CONFIG_DRIVER_SMC91111
+#ifdef CONFIG_SMC91111
 # define CONFIG_CMD_DHCP
 # define CONFIG_CMD_PING
 #else
@@ -205,32 +205,8 @@
  * them yet. You can (and probably should) change these values!
  */
 #ifdef CONFIG_SOFT_I2C
-
-#define PF_SCL                 PF9
-#define PF_SDA                 PF8
-
-#define I2C_INIT       do { *pFIO_DIR |= PF_SCL; SSYNC(); } while (0)
-#define I2C_ACTIVE     do { *pFIO_DIR |= PF_SDA; *pFIO_INEN &= ~PF_SDA; SSYNC(); } while (0)
-#define I2C_TRISTATE   do { *pFIO_DIR &= ~PF_SDA; *pFIO_INEN |= PF_SDA; SSYNC(); } while (0)
-#define I2C_READ       ((*pFIO_FLAG_D & PF_SDA) != 0)
-#define I2C_SDA(bit) \
-       do { \
-               if (bit) \
-                       *pFIO_FLAG_S = PF_SDA; \
-               else \
-                       *pFIO_FLAG_C = PF_SDA; \
-               SSYNC(); \
-       } while (0)
-#define I2C_SCL(bit) \
-       do { \
-               if (bit) \
-                       *pFIO_FLAG_S = PF_SCL; \
-               else \
-                       *pFIO_FLAG_C = PF_SCL; \
-               SSYNC(); \
-       } while (0)
-#define I2C_DELAY              udelay(5)       /* 1/4 I2C clock duration */
-
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
 #define CONFIG_SYS_I2C_SPEED           50000
 #define CONFIG_SYS_I2C_SLAVE           0xFE
 #endif