*
* U-Boot configuration for Embedded Planet EP8248 boards.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define CONFIG_EP8248 /* Embedded Planet EP8248 board */
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
#define CONFIG_SYS_BCSR 0xFA000000
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
+/* Pass open firmware flat device tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc/cpm/serial <at> 11a80"
+
+/* Select ethernet configuration */
#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
#undef CONFIG_ETHER_NONE /* No external Ethernet */
-#ifdef CONFIG_ETHER_ON_FCC
-
-#define CONFIG_ETHER_INDEX 1 /* FCC1 is used for Ethernet */
-
-#if (CONFIG_ETHER_INDEX == 1)
+#define CONFIG_SYS_CPMFCR_RAMTYPE 0
+#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHER_ON_FCC1 1
/* - Rx clock is CLK10
* - Tx clock is CLK11
* - BDs/buffers on 60x bus
* - Full duplex
*/
-#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF1CS_CLK10 | CMXFCR_TF1CS_CLK11)
-#define CONFIG_SYS_CPMFCR_RAMTYPE 0
-#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#elif (CONFIG_ETHER_INDEX == 2)
+#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK10 | CMXFCR_TF1CS_CLK11)
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETHER_ON_FCC2 1
/* - Rx clock is CLK13
* - Tx clock is CLK14
* - BDs/buffers on 60x bus
* - Full duplex
*/
-#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-#define CONFIG_SYS_CPMFCR_RAMTYPE 0
-#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
+#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
* GPIO pins used for bit-banged MII communications
*/
#define MDIO_PORT 0 /* Not used - implemented in BCSR */
+
#define MDIO_ACTIVE (*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
#define MDIO_TRISTATE (*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
#define MDIO_READ (*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
#define MIIDELAY udelay(1)
-#endif /* CONFIG_ETHER_ON_FCC */
-
#ifndef CONFIG_8260_CLKIN
#define CONFIG_8260_CLKIN 66000000 /* in Hz */
#endif
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
#endif
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_IMMR 0xF0000000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* Hard reset configuration word */
#define CONFIG_SYS_HRCW_SLAVE6 0
#define CONFIG_SYS_HRCW_SLAVE7 0
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
projects / karo-tx-uboot.git / blobdiff