/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_ELF | CFG_CMD_PCI)
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_PCI
+
#define CONFIG_PCI
+#define CONFIG_IXP_PCI
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-/* These are u-boot generic parameters */
-#include <cmd_confdefs.h>
#define CONFIG_BOOTDELAY 3
/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5b*/
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
#define CONFIG_CMDLINE_TAG
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0x00010000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
-#define CFG_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */
+#define CONFIG_SYS_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Stack sizes
/*
* select serial console configuration
*/
-#define CFG_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
+#define CONFIG_IXP_SERIAL
+#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
/*
* Physical Memory Map
#define PHYS_FLASH_BANK_SIZE 0x00800000 /* 8 MB Banks */
#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */
-#define CFG_DRAM_BASE 0x00000000
-#define CFG_DRAM_SIZE 0x01000000
+#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_DRAM_SIZE 0x01000000
-#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
/*
* Expansion bus settings
*/
-#define CFG_EXP_CS0 0xbcd23c42
+#define CONFIG_SYS_EXP_CS0 0xbcd23c42
/*
* SDRAM settings
*/
-#define CFG_SDR_CONFIG 0xd
-#define CFG_SDR_MODE_CONFIG 0x1
-#define CFG_SDRAM_REFRESH_CNT 0x81a
+#define CONFIG_SYS_SDR_CONFIG 0xd
+#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
+#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
/*
* GPIO settings
/*
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_ENV_IS_IN_FLASH 1
-#define CFG_FLASH_BANKS_LIST { PHYS_FLASH_1 }
+#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 }
-#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x20000)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x20000)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff