karo: fdt: fix panel-dpi support

[karo-tx-uboot.git] / include / configs / nios2-generic.h

diff --git a/include/configs/nios2-generic.h b/include/configs/nios2-generic.h
index b528f5a6225a2e0156204cb3e96b660676c2b5a3..945cbd4ee7b1c2353046fb0befce3f2764232a35 100644 (file)
--- a/include/configs/nios2-generic.h
+++ b/include/configs/nios2-generic.h
@@ -3,7 +3,7 @@
  * Scott McNutt <smcnutt@psyent.com>
  * (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -15,12 +15,14 @@
 #include "../board/altera/nios2-generic/custom_fpga.h" /* fpga parameters */
 #define CONFIG_BOARD_NAME "nios2-generic" /* custom board name */
 #define CONFIG_BOARD_EARLY_INIT_F      /* enable early board-spec. init */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_SYS_NIOS_SYSID_BASE     CONFIG_SYS_SYSID_BASE
 
 /*
  * SERIAL
  */
-#define CONFIG_ALTERA_UART
+#define CONFIG_ALTERA_JTAG_UART
 #if defined(CONFIG_ALTERA_JTAG_UART)
 # define CONFIG_SYS_NIOS_CONSOLE       CONFIG_SYS_JTAG_UART_BASE
 #else
@@ -39,7 +41,6 @@
 #define CONFIG_SYS_LOW_RES_TIMER
 #define CONFIG_SYS_NIOS_TMRBASE        CONFIG_SYS_TIMER_BASE
 #define CONFIG_SYS_NIOS_TMRIRQ         CONFIG_SYS_TIMER_IRQ
-#define CONFIG_SYS_HZ                  1000    /* Always 1000 */
 #define CONFIG_SYS_NIOS_TMRMS          10      /* Desired period (msec)*/
 #define CONFIG_SYS_NIOS_TMRCNT \
        (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_TIMER_FREQ / 1000) - 1)
@@ -55,6 +56,9 @@
 #define CONFIG_BOARD_SPECIFIC_LED
 #define CONFIG_GPIO_LED                /* Enable GPIO LED driver */
 #define CONFIG_GPIO                    /* Enable GPIO driver */
+#define LED_PIO_BASE                   USER_LED_PIO_8OUT_BASE
+#define LED_PIO_WIDTH                  8
+#define LED_PIO_RSTVAL                 0xff
 
 #define STATUS_LED_BIT                 0       /* Bit-0 on GPIO */
 #define STATUS_LED_STATE               1       /* Blinking */
@@ -71,20 +75,15 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BOOTD
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_ITEST
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-
 #ifdef CONFIG_CMD_NET
 # define CONFIG_CMD_DHCP
 # define CONFIG_CMD_PING
 #endif
 
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_LMB
+
 /*
  * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
  * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
@@ -94,7 +93,7 @@
  */
 #define CONFIG_ENV_IS_IN_FLASH
 
-#define CONFIG_ENV_SIZE                0x10000 /* 64k, 1 sector */
+#define CONFIG_ENV_SIZE                0x20000 /* 128k, 1 sector */
 #define CONFIG_ENV_OVERWRITE           /* Serial change Ok     */
 #define CONFIG_ENV_ADDR                ((CONFIG_SYS_RESET_ADDR + \
                                          CONFIG_SYS_MONITOR_LEN) | \
@@ -120,7 +119,6 @@
  * MISC
  */
 #define CONFIG_SYS_LONGHELP            /* Provide extended help */
-#define CONFIG_SYS_PROMPT              "==> "  /* Command prompt       */
 #define CONFIG_SYS_CBSIZE              256     /* Console I/O buf size */
 #define CONFIG_SYS_MAXARGS             16      /* Max command args     */
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Bootarg buf size */