*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define CONFIG_RTC_BF533 1
/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES 1
+#define SHARED_RESOURCES 1
#define CONFIG_VDSP 1
*
*/
-/* CONFIG_CLKIN_HZ is any value in Hz */
+/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
#define CONFIG_VCO_MULT 45
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
+/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 6
/*
* Network Settings
*/
/* network support */
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME STAMP
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME STAMP
#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
/*
* Command settings
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTCOMMAND "run ramboot"
#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_PING | \
CFG_CMD_ELF | \
CFG_CMD_I2C | \
CFG_CMD_CACHE | \
- CFG_CMD_JFFS2 | \
+ CFG_CMD_JFFS2 | \
CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw"
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw"
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw\0" \
#define CONFIG_BAUDRATE 57600
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_PROMPT "stamp>" /* Monitor Command Prompt */
+#define CFG_PROMPT "stamp>" /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_LOADS_ECHO 1
*
*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_CFI_AMD_RESET
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_CFI_AMD_RESET
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#define CFG_ENV_ADDR 0x20020000
-#define CFG_ENV_SIZE 0x10000
-#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CFG_ENV_SIZE 0x10000
+#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
#define CFG_JFFS2_FIRST_BANK 0
#define CFG_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
+#define CFG_JFFS2_FIRST_SECTOR 11
-/*
- * following timeouts shall be used once the
+/*
+ * following timeouts shall be used once the
* Flash real protection is enabled
*/
#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
*pFIO_FLAG_S = PF_SDA; \
asm("ssync;"); \
} \
- else { \
+ else { \
*pFIO_FLAG_C = PF_SDA; \
asm("ssync;"); \
}
*pFIO_FLAG_S = PF_SCL; \
asm("ssync;"); \
} \
- else { \
+ else { \
*pFIO_FLAG_C = PF_SCL; \
asm("ssync;"); \
}
/*
* IDE/ATA stuff
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
#define CFG_ATA_BASE_ADDR 0x20200000
#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
#define CFG_ATA_STRIDE 2
#endif
*
*/
-#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x07EFFFFF /* 1 ... 127 MB in DRAM */
-#define CFG_LOAD_ADDR 0x01000000 /* default load address */
+#define CFG_LOAD_ADDR 0x01000000 /* default load address */
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_MAX_RAM_SIZE 0x08000000
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-
-
-
#if ( CONFIG_CLKIN_HALF == 0 )
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
#else
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
-
-
/*
* Miscellaneous configurable options
*/
-#define CFG_HZ 1000 /* 1ms time tick */
+#define CFG_HZ 1000 /* 1ms time tick */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
#define CFG_GBL_DATA_SIZE 0x4000
#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
/*
* Stack sizes
*/
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
/*
* FLASH organization and environment definitions
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
-/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
- B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
-#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
- B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
+/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
+ B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
+#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
+ B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0xBBC3BBC3
-#define AMBCTL1VAL 0x99B39983
-#define CF_AMBCTL1VAL 0x99B3ffc2
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0xBBC3BBC3
+#define AMBCTL1VAL 0x99B39983
+#define CF_AMBCTL1VAL 0x99B3ffc2
#ifdef CONFIG_VDSP
#define ET_EXEC_VDSP 0x8
#define VDSP_ENTRY_ADDR 0xFFA00000
#endif
-
#endif
projects / karo-tx-uboot.git / blobdiff