Move setting CONFIG_BOOTP_VCI_STRING to before including the vexpress-common header

[karo-tx-uboot.git] / include / configs / stxssa.h

diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 805814f4fb92ab986c953771cccce28b1c312ec9..5b1f3ab4034a45cb57c6096dcd8cfbe1d3de644e 100644 (file)
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -13,7 +13,7 @@
 /* mpc8560ads board configuration file */
 /* please refer to doc/README.mpc85xx for more info */
 /* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+ * search for CONFIG_SERVERIP, etc. in this file
  */
 
 #ifndef __CONFIG_H
@@ -22,7 +22,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE                */
 #define CONFIG_E500            1       /* BOOKE e500 family    */
-#define CONFIG_MPC85xx         1       /* MPC8540/MPC8560      */
 #define CONFIG_CPM2            1       /* has CPM2 */
 #define CONFIG_STXSSA          1       /* Silicon Tx GPPP SSA board specific*/
 #define CONFIG_MPC8560         1
@@ -112,7 +111,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -323,13 +322,10 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SNTP
 #define CONFIG_CMD_REGINFO
@@ -342,10 +338,7 @@
     #define CONFIG_CMD_MII
 #endif
 
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#else
+#if !defined(CONFIG_SYS_RAMBOOT)
     #define CONFIG_CMD_ELF
 #endif
 
@@ -376,17 +369,12 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
-/*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR  00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:e0:0c:07:9b:8b
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:e0:0c:07:9b:8c
 #endif
 
 /*