arm/rpi: Enable dcache

[karo-tx-uboot.git] / include / configs / ti_armv7_common.h

diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 0aea7d12ec16c73ad7f4a3c4d1ae055c1a9cf5d9..6dc5ebdd3497d3296d456754eb211b9c0d3f791b 100644 (file)
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -18,8 +18,6 @@
 #define __CONFIG_TI_ARMV7_COMMON_H__
 
 /* Common define for many platforms. */
-#define CONFIG_OMAP
-#define CONFIG_OMAP_COMMON
 #define CONFIG_SYS_GENERIC_BOARD
 
 /*
@@ -76,8 +74,11 @@
 #define CONFIG_NR_DRAM_BANKS           1
 #endif
 #define CONFIG_SYS_SDRAM_BASE          0x80000000
+
+#ifndef CONFIG_SYS_INIT_SP_ADDR
 #define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
                                                GENERATED_GBL_DATA_SIZE)
+#endif
 
 /* Timer information. */
 #define CONFIG_SYS_PTV                 2       /* Divisor: 2^(PTV+1) => 8 */
@@ -86,38 +87,19 @@
 #define CONFIG_I2C
 #define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED    100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE    1
-#define CONFIG_SYS_I2C_OMAP24XX
 
 /* MMC/SD IP block */
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
 #define CONFIG_CMD_MMC
 
 /* McSPI IP block */
 #define CONFIG_SPI
-#define CONFIG_OMAP3_SPI
 #define CONFIG_CMD_SPI
 
 /* GPIO block */
-#define CONFIG_OMAP_GPIO
 #define CONFIG_CMD_GPIO
 
-/*
- * GPMC NAND block.  We support 1 device and the physical address to
- * access CS0 at is 0x8000000.
- */
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-#ifndef CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_NAND_BASE           0x8000000
-#endif
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_CMD_NAND
-#endif
-
 /*
  * The following are general good-enough settings for U-Boot.  We set a
  * large malloc pool as we generally have a lot of DDR, and we opt for
@@ -161,7 +143,7 @@
  * mtdparts, both for ease of use in U-Boot and for passing information
  * on to the Linux kernel.
  */
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND)
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
 #define CONFIG_MTD_DEVICE              /* Required for mtdparts */
 #define CONFIG_CMD_MTDPARTS
 #endif
@@ -252,15 +234,14 @@
 #define CONFIG_SPL_EXT_SUPPORT
 #endif
 
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_THUMB_BUILD /* Thumbs mode to save space in SPL */
-#endif
+#define CONFIG_SYS_THUMB_BUILD
 
 /* General parts of the framework, required. */
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_BOARD_INIT