#define __CONFIG_TI_ARMV7_COMMON_H__
/* Common define for many platforms. */
-#define CONFIG_OMAP
-#define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_GENERIC_BOARD
/*
* We typically do not contain NOR flash. In the cases where we do, we
/*
* Our DDR memory always starts at 0x80000000 and U-Boot shall have
* relocated itself to higher in memory by the time this value is used.
+ * However, set this to a 32MB offset to allow for easier Linux kernel
+ * booting as the default is often used as the kernel load address.
*/
-#define CONFIG_SYS_LOAD_ADDR 0x80000000
+#define CONFIG_SYS_LOAD_ADDR 0x82000000
+
+/*
+ * We setup defaults based on constraints from the Linux kernel, which should
+ * also be safe elsewhere. We have the default load at 32MB into DDR (for
+ * the kernel), FDT above 128MB (the maximum location for the end of the
+ * kernel), and the ramdisk 512KB above that (allowing for hopefully never
+ * seen large trees). We say all of this must be within the first 256MB
+ * as that will normally be within the kernel lowmem and thus visible via
+ * bootm_size and we only run on platforms with 256MB or more of memory.
+ */
+#define DEFAULT_LINUX_BOOT_ENV \
+ "loadaddr=0x82000000\0" \
+ "kernel_addr_r=0x82000000\0" \
+ "fdtaddr=0x88000000\0" \
+ "fdt_addr_r=0x88000000\0" \
+ "rdaddr=0x88080000\0" \
+ "ramdisk_addr_r=0x88080000\0" \
+ "bootm_size=0x10000000\0"
/*
* Default to a quick boot delay.
#define CONFIG_BOOTDELAY 1
/*
- * DDR information. We say (for simplicity) that we have 1 bank,
- * always, even when we have more. We always start at 0x80000000,
- * and we place the initial stack pointer in our SRAM.
+ * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
+ * we say (for simplicity) that we have 1 bank, always, even when
+ * we have more. We always start at 0x80000000, and we place the
+ * initial stack pointer in our SRAM. Otherwise, we can define
+ * CONFIG_NR_DRAM_BANKS before including this file.
*/
+#ifndef CONFIG_NR_DRAM_BANKS
#define CONFIG_NR_DRAM_BANKS 1
+#endif
#define CONFIG_SYS_SDRAM_BASE 0x80000000
+
+#ifndef CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
+#endif
/* Timer information. */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_I2C
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP24XX
/* MMC/SD IP block */
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
#define CONFIG_CMD_MMC
/* McSPI IP block */
#define CONFIG_SPI
-#define CONFIG_OMAP3_SPI
#define CONFIG_CMD_SPI
/* GPIO block */
-#define CONFIG_OMAP_GPIO
#define CONFIG_CMD_GPIO
-/*
- * GPMC NAND block. We support 1 device and the physical address to
- * access CS0 at is 0x8000000.
- */
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_NAND_BASE 0x8000000
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
-#endif
-
/*
* The following are general good-enough settings for U-Boot. We set a
* large malloc pool as we generally have a lot of DDR, and we opt for
* we are on so we do not need to rely on the command prompt. We set a
* console baudrate of 115200 and use the default baud rate table.
*/
-#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
+#ifdef CONFIG_DFU_MMC
+#define CONFIG_SYS_MALLOC_LEN ((16 << 20) + CONFIG_SYS_DFU_DATA_BUF_SIZE)
+#else
+#define CONFIG_SYS_MALLOC_LEN (16 << 20)
+#endif
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT "U-Boot# "
#define CONFIG_SYS_CONSOLE_INFO_QUIET
* mtdparts, both for ease of use in U-Boot and for passing information
* on to the Linux kernel.
*/
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND)
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
#define CONFIG_MTD_DEVICE /* Required for mtdparts */
#define CONFIG_CMD_MTDPARTS
#endif
-/*
- * For commands to use, we take the default list and add a few other
- * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH
- * prior to this include, in order to skip a few commands. When we do
- * have flash, if we expect these commands they must be enabled in that
- * config. If desired, a specific list of desired commands can be used
- * instead.
- */
-#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_ECHO
#define CONFIG_CMD_BOOTZ
+#define CONFIG_SUPPORT_RAW_INITRD
/*
* Common filesystems support. When we have removable storage we
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
#endif
/*
* under common/spl/. Given our generally common memory map, we set a
* number of related defaults and sizes here.
*/
-#ifndef CONFIG_NOR_BOOT
-#define CONFIG_SPL
+#if !defined(CONFIG_NOR_BOOT) && \
+ !(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_OS_BOOT
/*
- * Place the image at the start of the ROM defined image space.
- * We limit our size to the ROM-defined downloaded image area, and use the
- * rest of the space for stack. We load U-Boot itself into memory at
- * 0x80800000 for legacy reasons (to not conflict with older SPLs). We
- * have our BSS be placed 1MiB after this, to allow for the default
- * Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
- * We have the SPL malloc pool at the end of the BSS area.
+ * Place the image at the start of the ROM defined image space (per
+ * CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined
+ * downloaded image area. We initalize DRAM as soon as we can so that
+ * we can place stack, malloc and BSS there. We load U-Boot itself into
+ * memory at 0x80800000 for legacy reasons (to not conflict with older
+ * SPLs). We have our BSS be placed 2MiB after this, to allow for the
+ * default Linux kernel address of 0x80008000 to work with most sized
+ * kernels, in the Falcon Mode case. We have the SPL malloc pool at the
+ * end of the BSS area. We suggest that the stack be placed at 32MiB after
+ * the start of DRAM to allow room for all of the above (handled in Kconfig).
*/
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0x80800000
+#endif
+#ifndef CONFIG_SPL_BSS_START_ADDR
#define CONFIG_SPL_BSS_START_ADDR 0x80a00000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+#endif
+#ifndef CONFIG_SYS_SPL_MALLOC_START
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
+#endif
/* RAW SD card / eMMC locations. */
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
/* FAT sd card locations. */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
-
/* FAT */
-#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
-#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "args"
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
/* RAW SD card / eMMC */
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
-/* NAND */
-#ifdef CONFIG_NAND
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* end of u-boot */
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
-#endif
-
/* spl export command */
#define CONFIG_CMD_SPL
#endif
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_EXT_SUPPORT
#endif
+#define CONFIG_SYS_THUMB_BUILD
+
/* General parts of the framework, required. */
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_MTD_SUPPORT
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
#endif /* !CONFIG_NOR_BOOT */
+/* Generic Environment Variables */
+
+#ifdef CONFIG_CMD_NET
+#define NETARGS \
+ "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
+ "::off\0" \
+ "nfsopts=nolock\0" \
+ "rootpath=/export/rootfs\0" \
+ "netloadimage=tftp ${loadaddr} ${bootfile}\0" \
+ "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=/dev/nfs " \
+ "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+ "ip=dhcp\0" \
+ "netboot=echo Booting from network ...; " \
+ "setenv autoload no; " \
+ "dhcp; " \
+ "run netloadimage; " \
+ "run netloadfdt; " \
+ "run netargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0"
+#else
+#define NETARGS ""
+#endif
+
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
projects / karo-tx-uboot.git / blobdiff