sniper: Pass serial number through ATAG

[karo-tx-uboot.git] / include / configs / u8500_href.h

diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h
index 636922c2f9cb71510848fc543072572174eabfcf..6a225710c2c7ce8c448b12c6d64ccd03e503f8b9 100644 (file)
--- a/include/configs/u8500_href.h
+++ b/include/configs/u8500_href.h
@@ -1,23 +1,7 @@
 /*
  * Copyright (C) ST-Ericsson SA 2009
  *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -28,14 +12,12 @@
  * (easy to change)
  */
 #define CONFIG_U8500
-#define CONFIG_L2_OFF
 
 #define CONFIG_SYS_MEMTEST_START       0x00000000
 #define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF
-#define CONFIG_SYS_HZ          1000            /* must be 1000 */
 
 #define CONFIG_BOARD_EARLY_INIT_F
-#define BOARD_LATE_INIT
+#define CONFIG_BOARD_LATE_INIT
 
 /*
  * Size of malloc() pool
@@ -47,7 +29,6 @@
 #define CONFIG_ENV_SIZE                (128*1024)
 #define CONFIG_SYS_MALLOC_LEN  (CONFIG_ENV_SIZE + 256*1024)
 #endif
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* for initial data */
 
 /*
  * PL011 Configuration
@@ -70,7 +51,6 @@
                                  (void *)CFG_SERIAL2 }
 #define CONFIG_CONS_INDEX      2
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 
 /*
  * Devices and file systems
@@ -82,21 +62,9 @@
 /*
  * Commands
  */
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EMMC
-#define CONFIG_CMD_SOURCE
 #define CONFIG_CMD_I2C
 
 #ifndef CONFIG_BOOTDELAY
@@ -152,12 +120,10 @@
 #define CONFIG_SYS_MAXARGS     32      /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
 
-#undef CONFIG_SYS_CLKS_IN_HZ           /* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR           0x00100000 /* default load address */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE
 
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #define CONFIG_CMDLINE_EDITING
 
 #define CONFIG_SETUP_MEMORY_TAGS       2
@@ -169,7 +135,6 @@
  */
 #define CONFIG_U8500_I2C
 #undef CONFIG_HARD_I2C                 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED           100000
 #define CONFIG_SYS_I2C_SLAVE           0       /* slave addr of controller */
@@ -181,16 +146,6 @@
 
 #define CONFIG_SYS_I2C_GPIOE_ADDR      0x42    /* GPIO expander chip addr */
 #define CONFIG_TC35892_GPIO
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ           (4*1024)        /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ           (4*1024)        /* FIQ stack */
-#endif
 
 /*
  * Physical Memory Map
@@ -225,7 +180,6 @@
 #define CONFIG_MMC_DEV_NUM             1
 
 #define CONFIG_CMD_ENV
-#define CONFIG_CMD_SAVEENV     /* CMD_ENV is obsolete but used in env_emmc.c */
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_OFFSET              0x13F80000
 #define CONFIG_SYS_MMC_ENV_DEV          0               /* SLOT2: eMMC */