* Copyright 2010 Extreme Engineering Solutions, Inc.
* Copyright 2007-2008 Freescale Semiconductor, Inc.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
*/
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
#define CONFIG_P2020 1
#define CONFIG_XPEDITE550X 1
#define CONFIG_SYS_BOARD_NAME "XPedite5500"
#define CONFIG_SYS_FORM_PMC_XMC 1
#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xfff80000
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/*
* DDR config
*/
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-#define SPD_EEPROM_ADDRESS1 0x54
+#define SPD_EEPROM_ADDRESS 0x54
#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS 1
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR 0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/*
* Diagnostics
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
CONFIG_SYS_NAND_BASE2}
#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */
#define CONFIG_NAND_FSL_ELBC
* Use the HUSH parser
*/
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/*
* Pass open firmware flat tree
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C2_OFFSET 0x3100
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/* I2C DS7505 temperature sensor */
#define CONFIG_DTT_LM75
*/
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CONFIG_NET_MULTI 1
#define CONFIG_TSEC_TBI
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_ETHPRIME "eTSEC2"
+/*
+ * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
+ * 1000mbps SGMII link
+ */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+ TBICR_PHY_RESET \
+ | TBICR_FULL_DUPLEX \
+ | TBICR_SPEED1_SET \
+ )
+
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
/*
* Command configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PCI_ENUM
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-/*
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
/*
* Environment Configuration
*/
* f6f00000 - f7efffff Sec OS image (16MB)
* f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
*/
-#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000)
-#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000)
-#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000)
+#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
#define CONFIG_PROG_UBOOT1 \
"$download_cmd $loadaddr $ubootfile; " \
projects / karo-tx-uboot.git / blobdiff