#define _SPD_H_
typedef struct spd_eeprom_s {
- unsigned char info_size; /* # of bytes written into serial memory */
- unsigned char chip_size; /* Total # of bytes of SPD memory device */
- unsigned char mem_type; /* Fundamental memory type (FPM, EDO, SDRAM...) */
- unsigned char nrow_addr; /* # of Row Addresses on this assembly */
- unsigned char ncol_addr; /* # of Column Addresses on this assembly */
- unsigned char nrows; /* # of Module Rows on this assembly */
- unsigned char dataw_lsb; /* Data Width of this assembly */
- unsigned char dataw_msb; /* ... Data Width continuation */
- unsigned char voltage; /* Voltage interface standard of this assembly */
- unsigned char clk_cycle; /* SDRAM Cycle time at CL=X */
- unsigned char clk_access; /* SDRAM Access from Clock at CL=X */
- unsigned char config; /* DIMM Configuration type (non-parity, ECC) */
- unsigned char refresh; /* Refresh Rate/Type */
- unsigned char primw; /* Primary SDRAM Width */
- unsigned char ecw; /* Error Checking SDRAM width */
- unsigned char min_delay; /* Min Clock Delay for Back to Back Random Address */
- unsigned char burstl; /* Burst Lengths Supported */
- unsigned char nbanks; /* # of Banks on Each SDRAM Device */
- unsigned char cas_lat; /* CAS# Latencies Supported */
- unsigned char cs_lat; /* CS# Latency */
- unsigned char write_lat; /* Write Latency (also called Write Recovery time) */
- unsigned char mod_attr; /* SDRAM Module Attributes */
- unsigned char dev_attr; /* SDRAM Device Attributes */
- unsigned char clk_cycle2; /* Min SDRAM Cycle time at CL=X-1 */
- unsigned char clk_access2; /* SDRAM Access from Clock at CL=X-1 */
- unsigned char clk_cycle3; /* Min SDRAM Cycle time at CL=X-2 */
- unsigned char clk_access3; /* Max SDRAM Access from Clock at CL=X-2 */
- unsigned char trp; /* Min Row Precharge Time (tRP) */
- unsigned char trrd; /* Min Row Active to Row Active (tRRD) */
- unsigned char trcd; /* Min RAS to CAS Delay (tRCD) */
- unsigned char tras; /* Minimum RAS Pulse Width (tRAS) */
- unsigned char row_dens; /* Density of each row on module */
- unsigned char ca_setup; /* Command and Address signal input setup time */
- unsigned char ca_hold; /* Command and Address signal input hold time */
- unsigned char data_setup; /* Data signal input setup time */
- unsigned char data_hold; /* Data signal input hold time */
- unsigned char sset[26]; /* Superset Information (may be used in future) */
- unsigned char spd_rev; /* SPD Data Revision Code */
- unsigned char cksum; /* Checksum for bytes 0-62 */
- unsigned char mid[8]; /* Manufacturer's JEDEC ID code per JEP-108E */
- unsigned char mloc; /* Manufacturing Location */
- unsigned char mpart[18]; /* Manufacturer's Part Number */
- unsigned char rev[2]; /* Revision Code */
- unsigned char mdate[2]; /* Manufacturing Date */
- unsigned char sernum[4]; /* Assembly Serial Number */
- unsigned char mspec[27]; /* Manufacturer Specific Data */
- unsigned char freq; /* Intel specification frequency */
- unsigned char intel_cas; /* Intel Specification CAS# Latency support */
+ unsigned char info_size; /* 0 # bytes written into serial memory */
+ unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
+ unsigned char mem_type; /* 2 Fundamental memory type */
+ unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
+ unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
+ unsigned char nrows; /* 5 # of Module Rows on this assembly */
+ unsigned char dataw_lsb; /* 6 Data Width of this assembly */
+ unsigned char dataw_msb; /* 7 ... Data Width continuation */
+ unsigned char voltage; /* 8 Voltage intf std of this assembly */
+ unsigned char clk_cycle; /* 9 SDRAM Cycle time at CL=X */
+ unsigned char clk_access; /* 10 SDRAM Access from Clock at CL=X */
+ unsigned char config; /* 11 DIMM Configuration type */
+ unsigned char refresh; /* 12 Refresh Rate/Type */
+ unsigned char primw; /* 13 Primary SDRAM Width */
+ unsigned char ecw; /* 14 Error Checking SDRAM width */
+ unsigned char min_delay; /* 15 for Back to Back Random Address */
+ unsigned char burstl; /* 16 Burst Lengths Supported */
+ unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */
+ unsigned char cas_lat; /* 18 CAS# Latencies Supported */
+ unsigned char cs_lat; /* 19 CS# Latency */
+ unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */
+ unsigned char mod_attr; /* 21 SDRAM Module Attributes */
+ unsigned char dev_attr; /* 22 SDRAM Device Attributes */
+ unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time at CL=X-1 */
+ unsigned char clk_access2; /* 24 SDRAM Access from Clock at CL=X-1 */
+ unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time at CL=X-2 */
+ unsigned char clk_access3; /* 26 Max Access from Clock at CL=X-2 */
+ unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
+ unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
+ unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
+ unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
+ unsigned char row_dens; /* 31 Density of each row on module */
+ unsigned char ca_setup; /* 32 Cmd + Addr signal input setup time */
+ unsigned char ca_hold; /* 33 Cmd and Addr signal input hold time */
+ unsigned char data_setup; /* 34 Data signal input setup time */
+ unsigned char data_hold; /* 35 Data signal input hold time */
+ unsigned char twr; /* 36 Write Recovery time tWR */
+ unsigned char twtr; /* 37 Int write to read delay tWTR */
+ unsigned char trtp; /* 38 Int read to precharge delay tRTP */
+ unsigned char mem_probe; /* 39 Mem analysis probe characteristics */
+ unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */
+ unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
+ unsigned char trfc; /* 42 Min Auto to Active period tRFC */
+ unsigned char tckmax; /* 43 Max device cycle time tCKmax */
+ unsigned char tdqsq; /* 44 Max DQS to DQ skew */
+ unsigned char tqhs; /* 45 Max Read DataHold skew tQHS */
+ unsigned char pll_relock; /* 46 PLL Relock time */
+ unsigned char res[15]; /* 47-xx IDD in SPD and Reserved space */
+ unsigned char spd_rev; /* 62 SPD Data Revision Code */
+ unsigned char cksum; /* 63 Checksum for bytes 0-62 */
+ unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-108E */
+ unsigned char mloc; /* 72 Manufacturing Location */
+ unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
+ unsigned char rev[2]; /* 91 Revision Code */
+ unsigned char mdate[2]; /* 93 Manufacturing Date */
+ unsigned char sernum[4]; /* 95 Assembly Serial Number */
+ unsigned char mspec[27]; /* 99 Manufacturer Specific Data */
+
+ /*
+ * Open for Customer Use starting with byte 128.
+ */
+ unsigned char freq; /* 128 Intel spec: frequency */
+ unsigned char intel_cas; /* 129 Intel spec: CAS# Latency support */
} spd_eeprom_t;
+
+/*
+ * Byte 2 Fundamental Memory Types.
+ */
+#define SPD_MEMTYPE_FPM (0x01)
+#define SPD_MEMTYPE_EDO (0x02)
+#define SPD_MEMTYPE_PIPE_NIBBLE (0x03)
+#define SPD_MEMTYPE_SDRAM (0x04)
+#define SPD_MEMTYPE_ROM (0x05)
+#define SPD_MEMTYPE_SGRAM (0x06)
+#define SPD_MEMTYPE_DDR (0x07)
+#define SPD_MEMTYPE_DDR2 (0x08)
+
#endif /* _SPD_H_ */
projects / karo-tx-uboot.git / blobdiff