E: james.macaulay@amirix.com
D: Suppport for Amirix AP1000
W: www.amirix.com
+
+N: Timur Tabi
+E: timur@freescale.com
+D: Support for MPC8349E-mITX
+W: www.freescale.com
svm_sc8xx MPC8xx
+Timur Tabi <timur@freescale.com>
+
+ MPC8349E-mITX MPC8349
+
-------------------------------------------------------------------------
Unknown / orphaned boards:
#########################################################################
LIST_83xx=" \
- TQM834x MPC8349EMDS \
+ TQM834x MPC8349EMDS MPC8349ITX \
"
MPC8349EMDS_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx mpc8349emds
+MPC8349ITX_config: unconfig
+ @$(MKCONFIG) $(@:_config=) ppc mpc83xx mpc8349itx
+
#########################################################################
## MPC85xx Systems
#########################################################################
If SPD EEPROM is on an I2C bus other than the first one, specify here.
Note that the value must resolve to something your driver can deal with.
+- CFG_83XX_DDR_USES_CS0
+ Only for 83xx systems. If specified, then DDR should be configured
+ using CS0 and CS1 instead of CS2 and CS3.
+
+- CFG_83XX_DDR_USES_CS0
+ Only for 83xx systems. If specified, then DDR should be configured
+ using CS0 and CS1 instead of CS2 and CS3.
+
- CONFIG_ETHER_ON_FEC[12]
Define to enable FEC[12] on a 8xx series processor.
pci_init_board(void)
{
volatile immap_t * immr;
- volatile clk8349_t * clk;
- volatile law8349_t * pci_law;
- volatile pot8349_t * pci_pot;
- volatile pcictrl8349_t * pci_ctrl;
- volatile pciconf8349_t * pci_conf;
+ volatile clk83xx_t * clk;
+ volatile law83xx_t * pci_law;
+ volatile pot83xx_t * pci_pot;
+ volatile pcictrl83xx_t * pci_ctrl;
+ volatile pciconf83xx_t * pci_conf;
u16 reg16;
u32 reg32;
u32 dev;
struct pci_controller * hose;
immr = (immap_t *)CFG_IMMRBAR;
- clk = (clk8349_t *)&immr->clk;
+ clk = (clk83xx_t *)&immr->clk;
pci_law = immr->sysconf.pcilaw;
pci_pot = immr->ios.pot;
pci_ctrl = immr->pci_ctrl;
--- /dev/null
+#
+# Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o pci.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# MPC8349ITX
+#
+
+TEXT_BASE = 0xFEF00000
+
+ifneq ($(OBJTREE),$(SRCTREE))
+# We are building u-boot in a separate directory, use generated
+# .lds script from OBJTREE directory.
+LDSCRIPT := $(OBJTREE)/board/$(BOARDDIR)/u-boot.lds
+endif
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc83xx.h>
+#include <i2c.h>
+#include <spd.h>
+#include <miiphy.h>
+
+#ifdef CONFIG_PCI
+#include <asm/mpc8349_pci.h>
+#include <pci.h>
+#endif
+
+#ifdef CONFIG_SPD_EEPROM
+#include <spd_sdram.h>
+#else
+#include <asm/mmu.h>
+#endif
+
+#ifndef CONFIG_SPD_EEPROM
+/*************************************************************************
+ * fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+int fixed_sdram(void)
+{
+ volatile immap_t *im = (immap_t *) CFG_IMMRBAR;
+ u32 ddr_size; /* The size of RAM, in bytes */
+ u32 ddr_size_log2 = 0;
+
+ for (ddr_size = CFG_DDR_SIZE * 0x100000; ddr_size > 1; ddr_size >>= 1) {
+ if (ddr_size & 1) {
+ return -1;
+ }
+ ddr_size_log2++;
+ }
+
+ im->sysconf.ddrlaw[0].ar =
+ LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
+ im->sysconf.ddrlaw[0].bar = (CFG_DDR_SDRAM_BASE >> 12) & 0xfffff;
+
+ /* Only one CS0 for DDR */
+ im->ddr.csbnds[0].csbnds = 0x0000000f;
+ im->ddr.cs_config[0] = CFG_DDR_CONFIG;
+
+ debug("cs0_bnds = 0x%08x\n", im->ddr.csbnds[0].csbnds);
+ debug("cs0_config = 0x%08x\n", im->ddr.cs_config[0]);
+
+ debug("DDR:bar=0x%08x\n", im->sysconf.ddrlaw[0].bar);
+ debug("DDR:ar=0x%08x\n", im->sysconf.ddrlaw[0].ar);
+
+ im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+ im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;/* Was "2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT" */
+ im->ddr.sdram_cfg = SDRAM_CFG_SREN | SDRAM_CFG_SDRAM_TYPE_DDR;
+ im->ddr.sdram_mode =
+ (0x0000 << SDRAM_MODE_ESD_SHIFT) | (0x0032 << SDRAM_MODE_SD_SHIFT);
+ im->ddr.sdram_interval =
+ (0x0410 << SDRAM_INTERVAL_REFINT_SHIFT) | (0x0100 <<
+ SDRAM_INTERVAL_BSTOPRE_SHIFT);
+ im->ddr.sdram_clk_cntl =
+ DDR_SDRAM_CLK_CNTL_SS_EN | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
+
+ udelay(200);
+
+ im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+
+ debug("DDR:timing_cfg_1=0x%08x\n", im->ddr.timing_cfg_1);
+ debug("DDR:timing_cfg_2=0x%08x\n", im->ddr.timing_cfg_2);
+ debug("DDR:sdram_mode=0x%08x\n", im->ddr.sdram_mode);
+ debug("DDR:sdram_interval=0x%08x\n", im->ddr.sdram_interval);
+ debug("DDR:sdram_cfg=0x%08x\n", im->ddr.sdram_cfg);
+
+ return CFG_DDR_SIZE;
+}
+#endif
+
+#ifdef CONFIG_PCI
+/*
+ * Initialize PCI Devices, report devices found
+ */
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc83xxmitx_config_table[] = {
+ {
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0x0f,
+ PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ {
+ PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER}
+ },
+ {}
+}
+#endif
+
+volatile static struct pci_controller hose[] = {
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc83xxmitx_config_table,
+#endif
+ },
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc83xxmitx_config_table,
+#endif
+ }
+};
+#endif /* CONFIG_PCI */
+
+/* If MPC8349E-mITX is soldered with SDRAM, then initialize it.
+*/
+
+void sdram_init(void)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMRBAR;
+ volatile lbus83xx_t *lbc = &immap->lbus;
+
+#if defined(CFG_BR2_PRELIM) \
+ && defined(CFG_OR2_PRELIM) \
+ && defined(CFG_LBLAWBAR2_PRELIM) \
+ && defined(CFG_LBLAWAR2_PRELIM) \
+ && !defined(CONFIG_COMPACT_FLASH)
+
+ uint *sdram_addr = (uint *) CFG_LBC_SDRAM_BASE;
+
+ puts("\n SDRAM on Local Bus: ");
+ print_size(CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+ /*
+ * Setup SDRAM Base and Option Registers, already done in cpu_init.c
+ */
+
+ /*setup mtrpt, lsrt and lbcr for LB bus */
+ lbc->lbcr = CFG_LBC_LBCR;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ lbc->lsrt = CFG_LBC_LSRT;
+ asm("sync");
+
+ /*
+ * Configure the SDRAM controller Machine Mode register.
+ */
+ lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation */
+
+ lbc->lsdmr = CFG_LBC_LSDMR_1; /*0x68636733; precharge all the banks */
+ asm("sync");
+ *sdram_addr = 0xff;
+ udelay(100);
+
+ lbc->lsdmr = CFG_LBC_LSDMR_2; /*0x48636733; auto refresh */
+ asm("sync");
+ *sdram_addr = 0xff; /*1 time*/
+ udelay(100);
+ *sdram_addr = 0xff; /*2 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*3 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*4 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*5 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*6 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*7 times*/
+ udelay(100);
+ *sdram_addr = 0xff; /*8 times*/
+ udelay(100);
+
+ lbc->lsdmr = CFG_LBC_LSDMR_4; /*0x58636733;mode register write operation */
+ asm("sync");
+ *sdram_addr = 0xff;
+ udelay(100);
+
+ lbc->lsdmr = CFG_LBC_LSDMR_5; /*0x40636733;normal operation */
+ asm("sync");
+ *sdram_addr = 0xff;
+ udelay(100);
+
+#else
+ puts("SDRAM on Local Bus is NOT available!\n");
+
+#ifdef CFG_BR2_PRELIM
+ lbc->bank[2].br = CFG_BR2_PRELIM;
+ lbc->bank[2].or = CFG_OR2_PRELIM;
+#endif
+
+#ifdef CFG_BR3_PRELIM
+ lbc->bank[3].br = CFG_BR3_PRELIM;
+ lbc->bank[3].or = CFG_OR3_PRELIM;
+#endif
+#endif
+}
+
+long int initdram(int board_type)
+{
+ volatile immap_t *im = (immap_t *) CFG_IMMRBAR;
+ u32 msize = 0;
+#ifdef CONFIG_DDR_ECC
+ volatile ddr83xx_t *ddr = &im->ddr;
+#endif
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
+ return -1;
+
+ /* DDR SDRAM - Main SODIMM */
+ im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR;
+#ifdef CONFIG_SPD_EEPROM
+ msize = spd_sdram();
+#else
+ msize = fixed_sdram();
+#endif
+
+#ifdef CONFIG_DDR_ECC
+ if (ddr->sdram_cfg & SDRAM_CFG_ECC_EN)
+ /* Unlike every other board, on the 83xx spd_sdram() returns
+ megabytes instead of just bytes. That's why we need to
+ multiple by 1MB when calling ddr_enable_ecc(). */
+ ddr_enable_ecc(msize * 1048576);
+#endif
+
+ /*
+ * Initialize SDRAM if it is on local bus.
+ */
+ sdram_init();
+ puts(" DDR RAM: ");
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize * 1024 * 1024;
+}
+
+int checkboard(void)
+{
+#ifdef CONFIG_HARD_I2C
+ u8 i2c_data;
+#endif
+
+ puts("Board: Freescale MPC8349E-mITX");
+
+#ifdef CONFIG_HARD_I2C
+ i2c_set_bus_num(I2C_BUS_2);
+ if (i2c_read(CFG_I2C_8574A_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data)) ==
+ 0)
+ printf(" %u.%u (PCF8475A)", (i2c_data & 0x02) >> 1,
+ i2c_data & 0x01);
+ else if (i2c_read(CFG_I2C_8574_ADDR2, 0, 0, &i2c_data, sizeof(i2c_data))
+ == 0)
+ printf(" %u.%u (PCF8475)", (i2c_data & 0x02) >> 1,
+ i2c_data & 0x01);
+ else
+ printf(" ?.?");
+#endif
+
+ puts("\n");
+
+ return 0;
+}
+
+/**
+ * Implement a work-around for a hardware problem with compact
+ * flash.
+ *
+ * Program the UPM if compact flash is enabled.
+ */
+int misc_init_f(void)
+{
+ volatile u32 *vsc7385_cpuctrl;
+
+ /* 0x1c0c0 is the VSC7385 CPU Control (CPUCTRL) Register. The power up
+ default of VSC7385 L1_IRQ and L2_IRQ requests are active high. That
+ means it is 0 when the IRQ is not active. This makes the wire-AND
+ logic always assert IRQ7 to CPU even if there is no request from the
+ switch. Since the compact flash and the switch share the same IRQ,
+ the Linux kernel will think that the compact flash is requesting irq
+ and get stuck when it tries to clear the IRQ. Thus we need to set
+ the L2_IRQ0 and L2_IRQ1 to active low.
+
+ The following code sets the L1_IRQ and L2_IRQ polarity to active low.
+ Without this code, compact flash will not work in Linux because
+ unlike U-Boot, Linux uses the IRQ, so this code is necessary if we
+ don't enable compact flash for U-Boot.
+ */
+
+ vsc7385_cpuctrl = (volatile u32 *)(CFG_VSC7385_BASE + 0x1c0c0);
+ *vsc7385_cpuctrl |= 0x0c;
+
+#ifdef CONFIG_COMPACT_FLASH
+ /* UPM Table Configuration Code */
+ static uint UPMATable[] = {
+ 0xcffffc00, 0x0fffff00, 0x0fafff00, 0x0fafff00,
+ 0x0faffd00, 0x0faffc04, 0x0ffffc00, 0x3ffffc01,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfff7fc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+ 0xcffffc00, 0x0fffff00, 0x0ff3ff00, 0x0ff3ff00,
+ 0x0ff3fe00, 0x0ffffc00, 0x3ffffc05, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01
+ };
+ volatile immap_t *immap = (immap_t *) CFG_IMMRBAR;
+ volatile lbus83xx_t *lbus = &immap->lbus;
+
+ lbus->bank[3].br = CFG_BR3_PRELIM;
+ lbus->bank[3].or = CFG_OR3_PRELIM;
+
+ /* Program the MAMR. RFEN=0, OP=00, UWPL=1, AM=000, DS=01, G0CL=000,
+ GPL4=0, RLF=0001, WLF=0001, TLF=0001, MAD=000000
+ */
+ lbus->mamr = 0x08404440;
+
+ upmconfig(0, UPMATable, sizeof(UPMATable) / sizeof(UPMATable[0]));
+
+ puts("UPMA: Configured for compact flash\n");
+#endif
+
+ return 0;
+}
+
+/**
+ * Make sure the EEPROM has the HRCW correctly programmed.
+ * Make sure the RTC is correctly programmed.
+ *
+ * The MPC8349E-mITX can be configured to load the HRCW from
+ * EEPROM instead of flash. This is controlled via jumpers
+ * LGPL0, 1, and 3. Normally, these jumpers are set to 000 (all
+ * jumpered), but if they're set to 001 or 010, then the HRCW is
+ * read from the "I2C EEPROM".
+ *
+ * This function makes sure that the I2C EEPROM is programmed
+ * correctly.
+ */
+int misc_init_r(void)
+{
+ int rc = 0;
+
+#ifdef CONFIG_HARD_I2C
+
+ uchar orig_bus = i2c_get_bus_num();;
+
+#ifdef CFG_I2C_RTC_ADDR
+ char ds1339_data[17];
+#endif
+
+#ifdef CFG_I2C_EEPROM_ADDR
+ static u8 eeprom_data[] = /* HRCW data */
+ {
+ 0xaa, 0x55, 0xaa,
+ 0x7c, 0x02, 0x40, 0x05, 0x04, 0x00, 0x00,
+ 0x7c, 0x02, 0x41, 0xb4, 0x60, 0xa0, 0x00,
+ };
+
+ u8 data[sizeof(eeprom_data)];
+
+ i2c_set_bus_num(I2C_BUS_1);
+
+ if (i2c_read(CFG_I2C_EEPROM_ADDR, 0, 2, data, sizeof(data)) == 0) {
+ if (memcmp(data, eeprom_data, sizeof(data)) != 0) {
+ if (i2c_write
+ (CFG_I2C_EEPROM_ADDR, 0, 2, eeprom_data,
+ sizeof(eeprom_data)) != 0) {
+ puts("Failure writing the HRCW to EEPROM via I2C.\n");
+ rc = 1;
+ }
+ }
+ } else {
+ puts("Failure reading the HRCW from EEPROM via I2C.\n");
+ rc = 1;
+ }
+#endif
+
+#ifdef CFG_I2C_RTC_ADDR
+ i2c_set_bus_num(I2C_BUS_2);
+
+ if (i2c_read(CFG_I2C_RTC_ADDR, 0, 1, ds1339_data, sizeof(ds1339_data))
+ == 0) {
+
+ /* Work-around for MPC8349E-mITX bug #13601.
+ If the RTC does not contain valid register values, the DS1339
+ Linux driver will not work.
+ */
+
+ /* Make sure status register bits 6-2 are zero */
+ ds1339_data[0x0f] &= ~0x7c;
+
+ /* Check for a valid day register value */
+ ds1339_data[0x03] &= ~0xf8;
+ if (ds1339_data[0x03] == 0) {
+ ds1339_data[0x03] = 1;
+ }
+
+ /* Check for a valid date register value */
+ ds1339_data[0x04] &= ~0xc0;
+ if ((ds1339_data[0x04] == 0) ||
+ ((ds1339_data[0x04] & 0x0f) > 9) ||
+ (ds1339_data[0x04] >= 0x32)) {
+ ds1339_data[0x04] = 1;
+ }
+
+ /* Check for a valid month register value */
+ ds1339_data[0x05] &= ~0x60;
+
+ if ((ds1339_data[0x05] == 0) ||
+ ((ds1339_data[0x05] & 0x0f) > 9) ||
+ ((ds1339_data[0x05] >= 0x13)
+ && (ds1339_data[0x05] <= 0x19))) {
+ ds1339_data[0x05] = 1;
+ }
+
+ /* Enable Oscillator and rate select */
+ ds1339_data[0x0e] = 0x1c;
+
+ /* Work-around for MPC8349E-mITX bug #13330.
+ Ensure that the RTC control register contains the value 0x1c.
+ This affects SATA performance.
+ */
+
+ if (i2c_write
+ (CFG_I2C_RTC_ADDR, 0, 1, ds1339_data,
+ sizeof(ds1339_data))) {
+ puts("Failure writing to the RTC via I2C.\n");
+ rc = 1;
+ }
+ } else {
+ puts("Failure reading from the RTC via I2C.\n");
+ rc = 1;
+ }
+#endif
+
+ i2c_set_bus_num(orig_bus);
+#endif
+
+ return rc;
+}
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_PCI
+
+#include <asm/mmu.h>
+#include <asm/global_data.h>
+#include <pci.h>
+#include <asm/mpc8349_pci.h>
+#include <i2c.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc8349itx_config_table[] = {
+ {
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ PCI_IDSEL_NUMBER,
+ PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ {
+ PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER}
+ },
+ {}
+};
+#endif
+
+static struct pci_controller pci_hose[] = {
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc8349itx_config_table,
+#endif
+ },
+ {
+#ifndef CONFIG_PCI_PNP
+ config_table:pci_mpc8349itx_config_table,
+#endif
+ }
+};
+
+/**************************************************************************
+ * pci_init_board()
+ *
+ * NOTICE: PCI2 is not currently supported
+ *
+ */
+void pci_init_board(void)
+{
+ volatile immap_t *immr;
+ volatile clk83xx_t *clk;
+ volatile law83xx_t *pci_law;
+ volatile pot83xx_t *pci_pot;
+ volatile pcictrl83xx_t *pci_ctrl;
+ volatile pciconf83xx_t *pci_conf;
+ u8 reg8;
+ u16 reg16;
+ u32 reg32;
+ u32 dev;
+ struct pci_controller *hose;
+
+ immr = (immap_t *) CFG_IMMRBAR;
+ clk = (clk83xx_t *) & immr->clk;
+ pci_law = immr->sysconf.pcilaw;
+ pci_pot = immr->ios.pot;
+ pci_ctrl = immr->pci_ctrl;
+ pci_conf = immr->pci_conf;
+
+ hose = &pci_hose[0];
+
+ /*
+ * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
+ */
+
+ reg32 = clk->occr;
+ udelay(2000);
+
+#ifdef CONFIG_HARD_I2C
+ i2c_set_bus_num(I2C_BUS_2);
+ /* Read the PCI_M66EN jumper setting */
+ if ((i2c_read(CFG_I2C_8574_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0) ||
+ (i2c_read(CFG_I2C_8574A_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0)) {
+ if (reg8 & I2C_8574_PCI66)
+ clk->occr = 0xff000000; /* 66 MHz PCI */
+ else
+ clk->occr = 0xff600001; /* 33 MHz PCI */
+ } else {
+ clk->occr = 0xff600001; /* 33 MHz PCI */
+ }
+#else
+ clk->occr = 0xff000000; /* 66 MHz PCI */
+#endif
+
+ udelay(2000);
+
+ /*
+ * Release PCI RST Output signal
+ */
+ pci_ctrl[0].gcr = 0;
+ udelay(2000);
+ pci_ctrl[0].gcr = 1;
+
+#ifdef CONFIG_MPC83XX_PCI2
+ pci_ctrl[1].gcr = 0;
+ udelay(2000);
+ pci_ctrl[1].gcr = 1;
+#endif
+
+ /* We need to wait at least a 1sec based on PCI specs */
+ {
+ int i;
+
+ for (i = 0; i < 1000; i++)
+ udelay(1000);
+ }
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
+
+ pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+
+ /* PCI1 mem space - prefetch */
+ pci_pot[0].potar = (CFG_PCI1_MEM_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[0].pobar = (CFG_PCI1_MEM_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[0].pocmr =
+ POCMR_EN | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /* PCI1 IO space */
+ pci_pot[1].potar = (CFG_PCI1_IO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[1].pobar = (CFG_PCI1_IO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[1].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+ /* PCI1 mmio - non-prefetch mem space */
+ pci_pot[2].potar = (CFG_PCI1_MMIO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[2].pobar = (CFG_PCI1_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[2].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+
+ /* we need RAM mapped to PCI space for the devices to
+ * access main memory */
+ pci_ctrl[0].pitar1 = 0x0;
+ pci_ctrl[0].pibar1 = 0x0;
+ pci_ctrl[0].piebar1 = 0x0;
+ pci_ctrl[0].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
+ PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ /* PCI memory prefetch space */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI1_MEM_BASE,
+ CFG_PCI1_MEM_PHYS,
+ CFG_PCI1_MEM_SIZE, PCI_REGION_MEM | PCI_REGION_PREFETCH);
+
+ /* PCI memory space */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI1_MMIO_BASE,
+ CFG_PCI1_MMIO_PHYS, CFG_PCI1_MMIO_SIZE, PCI_REGION_MEM);
+
+ /* PCI IO space */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI1_IO_BASE,
+ CFG_PCI1_IO_PHYS, CFG_PCI1_IO_SIZE, PCI_REGION_IO);
+
+ /* System memory space */
+ pci_set_region(hose->regions + 3,
+ CONFIG_PCI_SYS_MEM_BUS,
+ CONFIG_PCI_SYS_MEM_PHYS,
+ gd->ram_size, PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ hose->region_count = 4;
+
+ pci_setup_indirect(hose,
+ (CFG_IMMRBAR + 0x8300), (CFG_IMMRBAR + 0x8304));
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word(hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+ printf("PCI: Bus Dev VenId DevId Class Int\n");
+#endif
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+
+#ifdef CONFIG_MPC83XX_PCI2
+ hose = &pci_hose[1];
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+
+ /* PCI2 mem space - prefetch */
+ pci_pot[3].potar = (CFG_PCI2_MEM_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[3].pobar = (CFG_PCI2_MEM_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[3].pocmr =
+ POCMR_EN | POCMR_PCI2 | POCMR_PREFETCH_EN | (POCMR_CM_256M &
+ POCMR_CM_MASK);
+
+ /* PCI2 IO space */
+ pci_pot[4].potar = (CFG_PCI2_IO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[4].pobar = (CFG_PCI2_IO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[4].pocmr =
+ POCMR_EN | POCMR_PCI2 | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+ /* PCI2 mmio - non-prefetch mem space */
+ pci_pot[5].potar = (CFG_PCI2_MMIO_BASE >> 12) & POTAR_TA_MASK;
+ pci_pot[5].pobar = (CFG_PCI2_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+ pci_pot[5].pocmr =
+ POCMR_EN | POCMR_PCI2 | (POCMR_CM_256M & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+
+ /* we need RAM mapped to PCI space for the devices to
+ * access main memory */
+ pci_ctrl[1].pitar1 = 0x0;
+ pci_ctrl[1].pibar1 = 0x0;
+ pci_ctrl[1].piebar1 = 0x0;
+ pci_ctrl[1].piwar1 =
+ PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP |
+ (__ilog2(gd->ram_size) - 1);
+
+ hose->first_busno = pci_hose[0].last_busno + 1;
+ hose->last_busno = 0xff;
+
+ /* PCI memory prefetch space */
+ pci_set_region(hose->regions + 0,
+ CFG_PCI2_MEM_BASE,
+ CFG_PCI2_MEM_PHYS,
+ CFG_PCI2_MEM_SIZE, PCI_REGION_MEM | PCI_REGION_PREFETCH);
+
+ /* PCI memory space */
+ pci_set_region(hose->regions + 1,
+ CFG_PCI2_MMIO_BASE,
+ CFG_PCI2_MMIO_PHYS, CFG_PCI2_MMIO_SIZE, PCI_REGION_MEM);
+
+ /* PCI IO space */
+ pci_set_region(hose->regions + 2,
+ CFG_PCI2_IO_BASE,
+ CFG_PCI2_IO_PHYS, CFG_PCI2_IO_SIZE, PCI_REGION_IO);
+
+ /* System memory space */
+ pci_set_region(hose->regions + 3,
+ CONFIG_PCI_SYS_MEM_BUS,
+ CONFIG_PCI_SYS_MEM_PHYS,
+ gd->ram_size, PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+ hose->region_count = 4;
+
+ pci_setup_indirect(hose,
+ (CFG_IMMRBAR + 0x8380), (CFG_IMMRBAR + 0x8384));
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word(hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+#endif
+}
+
+#endif /* CONFIG_PCI */
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc83xx/start.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ . = ALIGN(16);
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x0FFF) & 0xFFFFF000;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(4096);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(4096);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
+ENTRY(_start)
}
+/**
+ * Program a UPM with the code supplied in the table.
+ *
+ * The 'dummy' variable is used to increment the MAD. 'dummy' is
+ * supposed to be a pointer to the memory of the device being
+ * programmed by the UPM. The data in the MDR is written into
+ * memory and the MAD is incremented every time there's a read
+ * from 'dummy'. Unfortunately, the current prototype for this
+ * function doesn't allow for passing the address of this
+ * device, and changing the prototype will break a number lots
+ * of other code, so we need to use a round-about way of finding
+ * the value for 'dummy'.
+ *
+ * The value can be extracted from the base address bits of the
+ * Base Register (BR) associated with the specific UPM. To find
+ * that BR, we need to scan all 8 BRs until we find the one that
+ * has its MSEL bits matching the UPM we want. Once we know the
+ * right BR, we can extract the base address bits from it.
+ *
+ * The MxMR and the BR and OR of the chosen bank should all be
+ * configured before calling this function.
+ *
+ * Parameters:
+ * upm: 0=UPMA, 1=UPMB, 2=UPMC
+ * table: Pointer to an array of values to program
+ * size: Number of elements in the array. Must be 64 or less.
+*/
void upmconfig (uint upm, uint *table, uint size)
{
- hang(); /* FIXME: upconfig() needed? */
+#if defined(CONFIG_MPC834X)
+ volatile immap_t *immap = (immap_t *) CFG_IMMRBAR;
+ volatile lbus83xx_t *lbus = &immap->lbus;
+ volatile uchar *dummy = NULL;
+ const u32 msel = (upm + 4) << BR_MSEL_SHIFT; /* What the MSEL field in BRn should be */
+ volatile u32 *mxmr = &lbus->mamr + upm; /* Pointer to mamr, mbmr, or mcmr */
+ uint i;
+
+ /* Scan all the banks to determine the base address of the device */
+ for (i = 0; i < 8; i++) {
+ if ((lbus->bank[i].br & BR_MSEL) == msel) {
+ dummy = (uchar *) (lbus->bank[i].br & BR_BA);
+ break;
+ }
+ }
+
+ if (!dummy) {
+ printf("Error: %s() could not find matching BR\n", __FUNCTION__);
+ hang();
+ }
+
+ /* Set the OP field in the MxMR to "write" and the MAD field to 000000 */
+ *mxmr = (*mxmr & 0xCFFFFFC0) | 0x10000000;
+
+ for (i = 0; i < size; i++) {
+ lbus->mdr = table[i];
+ __asm__ __volatile__ ("sync");
+ *dummy; /* Write the value to memory and increment MAD */
+ __asm__ __volatile__ ("sync");
+ }
+
+ /* Set the OP field in the MxMR to "normal" and the MAD field to 000000 */
+ *mxmr &= 0xCFFFFFC0;
+#else
+ printf("Error: %s() not defined for this configuration.\n", __FUNCTION__);
+ hang();
+#endif
}
#if defined(CONFIG_WATCHDOG)
void watchdog_reset (void)
{
- hang(); /* FIXME: implement watchdog_reset()? */
+#ifdef CONFIG_MPC834X
+ int re_enable = disable_interrupts();
+
+ /* Reset the 83xx watchdog */
+ volatile immap_t *immr = (immap_t *) CFG_IMMRBAR;
+ immr->wdt.swsrr = 0x556c;
+ immr->wdt.swsrr = 0xaa39;
+
+ if (re_enable)
+ enable_interrupts ();
+#else
+ hang();
+#endif
}
-#endif /* CONFIG_WATCHDOG */
+#endif
#if defined(CONFIG_OF_FLAT_TREE)
void
/* Clear initial global data */
memset ((void *) gd, 0, sizeof (gd_t));
+ /* system performance tweaking */
+
+#ifdef CFG_ACR_PIPE_DEP
+ /* Arbiter pipeline depth */
+ im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) | (3 << ACR_PIPE_DEP_SHIFT);
+#endif
+
+#ifdef CFG_SPCR_TSEC1EP
+ /* TSEC1 Emergency priority */
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) | (3 << SPCR_TSEC1EP_SHIFT);
+#endif
+
+#ifdef CFG_SPCR_TSEC2EP
+ /* TSEC2 Emergency priority */
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) | (3 << SPCR_TSEC2EP_SHIFT);
+#endif
+
+#ifdef CFG_SCCR_TSEC1CM
+ /* TSEC1 clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) | (1 << SCCR_TSEC1CM_SHIFT);
+#endif
+#ifdef CFG_SCCR_TSEC2CM
+ /* TSEC2 & I2C1 clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) | (1 << SCCR_TSEC2CM_SHIFT);
+#endif
+
+#ifdef CFG_ACR_RPTCNT
+ /* Arbiter repeat count */
+ im->arbiter.acr = ((im->arbiter.acr & ~(ACR_RPTCNT)) | (3 << ACR_RPTCNT_SHIFT));
+#endif
+
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
gd->reset_status = im->reset.rsr;
im->reset.rsr = ~(RSR_RES);
/* Read SPD parameters with I2C */
+#ifdef CFG_83XX_DDR_USES_CS0
+ ddr->csbnds[0].csbnds = (banksize(spd.row_dens) >> 24) - 1;
+ ddr->cs_config[0] = ( 1 << 31
+ | (spd.nrow_addr - 12) << 8
+ | (spd.ncol_addr - 8) );
+ debug("\n");
+ debug("cs0_bnds = 0x%08x\n",ddr->csbnds[0].csbnds);
+ debug("cs0_config = 0x%08x\n",ddr->cs_config[0]);
+
+ if (spd.nrows == 2) {
+ ddr->csbnds[1].csbnds = ( (banksize(spd.row_dens) >> 8)
+ | ((banksize(spd.row_dens) >> 23) - 1) );
+ ddr->cs_config[1] = ( 1<<31
+ | (spd.nrow_addr-12) << 8
+ | (spd.ncol_addr-8) );
+ debug("cs1_bnds = 0x%08x\n",ddr->csbnds[1].csbnds);
+ debug("cs1_config = 0x%08x\n",ddr->cs_config[1]);
+ }
+
+#else
CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd));
#ifdef SPD_DEBUG
spd_debug(&spd);
debug("cs3_bnds = 0x%08x\n",ddr->csbnds[3].csbnds);
debug("cs3_config = 0x%08x\n",ddr->cs_config[3]);
}
+#endif
if (spd.mem_type != 0x07) {
puts("No DDR module found!\n");
};
struct phy_info *phy_info[] = {
-#if 0
- &phy_info_cis8201,
-#endif
&phy_info_cis8204,
+ &phy_info_cis8201,
&phy_info_M88E1011S,
&phy_info_M88E1111S,
&phy_info_M88E1145,
u8 res5[0x04];
u32 spcr; /* System Priority Configuration Register */
#define SPCR_PCIHPE 0x10000000 /* PCI Highest Priority Enable. */
+#define SPCR_PCIHPE_SHIFT (31-3)
#define SPCR_PCIPR 0x03000000 /* PCI bridge system bus request priority. */
+#define SPCR_PCIPR_SHIFT (31-7)
#define SPCR_TBEN 0x00400000 /* E300 PowerPC core time base unit enable. */
+#define SPCR_TBEN_SHIFT (31-9)
#define SPCR_COREPR 0x00300000 /* E300 PowerPC Core system bus request priority. */
+#define SPCR_COREPR_SHIFT (31-11)
#define SPCR_TSEC1DP 0x00003000 /* TSEC1 data priority. */
+#define SPCR_TSEC1DP_SHIFT (31-19)
#define SPCR_TSEC1BDP 0x00000C00 /* TSEC1 buffer descriptor priority. */
+#define SPCR_TSEC1BDP_SHIFT (31-21)
#define SPCR_TSEC1EP 0x00000300 /* TSEC1 emergency priority. */
+#define SPCR_TSEC1EP_SHIFT (31-23)
#define SPCR_TSEC2DP 0x00000030 /* TSEC2 data priority. */
+#define SPCR_TSEC2DP_SHIFT (31-27)
#define SPCR_TSEC2BDP 0x0000000C /* TSEC2 buffer descriptor priority. */
+#define SPCR_TSEC2BDP_SHIFT (31-29)
#define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority. */
+#define SPCR_TSEC2EP_SHIFT (31-31)
#define SPCR_RES ~(SPCR_PCIHPE | SPCR_PCIPR | SPCR_TBEN | SPCR_COREPR \
| SPCR_TSEC1DP | SPCR_TSEC1BDP | SPCR_TSEC1EP \
| SPCR_TSEC2DP | SPCR_TSEC2BDP | SPCR_TSEC2EP)
typedef struct arbiter83xx {
u32 acr; /* Arbiter Configuration Register */
#define ACR_COREDIS 0x10000000 /* Core disable. */
+#define ACR_COREDIS_SHIFT (31-7)
#define ACR_PIPE_DEP 0x00070000 /* Pipeline depth (number of outstanding transactions). */
+#define ACR_PIPE_DEP_SHIFT (31-15)
#define ACR_PCI_RPTCNT 0x00007000 /* PCI repeat count. */
+#define ACR_PCI_RPTCNT_SHIFT (31-19)
#define ACR_RPTCNT 0x00000700 /* Repeat count. */
+#define ACR_RPTCNT_SHIFT (31-23)
#define ACR_APARK 0x00000030 /* Address parking. */
+#define ACR_APARK_SHIFT (31-27)
#define ACR_PARKM 0x0000000F /* Parking master. */
+#define ACR_PARKM_SHIFT (31-31)
#define ACR_RES ~(ACR_COREDIS|ACR_PIPE_DEP|ACR_PCI_RPTCNT|ACR_RPTCNT|ACR_APARK|ACR_PARKM)
u32 atr; /* Arbiter Timers Register */
#define ATR_DTO 0x00FF0000 /* Data time out. */
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ MPC8349E-mITX board configuration file
+
+ Memory map:
+
+ 0x0000_0000-0x0FFF_FFFF DDR SDRAM (256 MB)
+ 0x8000_0000-0x9FFF_FFFF PCI1 memory space (512 MB)
+ 0xA000_0000-0xBFFF_FFFF PCI2 memory space (512 MB)
+ 0xE000_0000-0xEFFF_FFFF IMMR (1 MB)
+ 0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB)
+ 0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB)
+ 0xF000_0000-0xF000_FFFF Compact Flash
+ 0xF001_0000-0xF001_FFFF Local bus expansion slot
+ 0xF800_0000-0xF801_FFFF GBE L2 Switch VSC7385
+ 0xFF00_0000-0xFF7F_FFFF Alternative bank of Flash memory (8MB)
+ 0xFF80_0000-0xFFFF_FFFF Boot Flash (8 MB)
+
+ I2C address list:
+ Align. Board
+ Bus Addr Part No. Description Length Location
+ ----------------------------------------------------------------
+ I2C1 0x50 M24256-BWMN6P Board EEPROM 2 U64
+
+ I2C2 0x20 PCF8574 I2C Expander 0 U8
+ I2C2 0x21 PCF8574 I2C Expander 0 U10
+ I2C2 0x38 PCF8574A I2C Expander 0 U8
+ I2C2 0x39 PCF8574A I2C Expander 0 U10
+ I2C2 0x51 (DDR) DDR EEPROM 1 U1
+ I2C2 0x68 DS1339 RTC 1 U68
+
+ Note that a given board has *either* a pair of 8574s or a pair of 8574As.
+*/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC834X /* MPC834x family (8343, 8347, 8349) */
+#define CONFIG_MPC8349 /* MPC8349 specific */
+
+#define CONFIG_PCI
+
+#define CONFIG_COMPACT_FLASH /* The CF card interface on the back of the board */
+#define CONFIG_RTC_DS1337
+
+/* I2C */
+#define CONFIG_HARD_I2C
+
+#ifdef CONFIG_HARD_I2C
+
+#define CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+#define CFG_SPD_BUS_NUM I2C_2
+
+#define CFG_I2C_8574_ADDR1 0x20 /* I2C2, PCF8574 */
+#define CFG_I2C_8574_ADDR2 0x21 /* I2C2, PCF8574 */
+#define CFG_I2C_8574A_ADDR1 0x38 /* I2C2, PCF8574A */
+#define CFG_I2C_8574A_ADDR2 0x39 /* I2C2, PCF8574A */
+#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C1, Board EEPROM */
+#define CFG_I2C_RTC_ADDR 0x68 /* I2C2, DS1339 RTC*/
+#define SPD_EEPROM_ADDRESS 0x51 /* I2C2, DDR */
+
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+/* Don't probe these addresses: */
+#define CFG_I2C_NOPROBES {{1, CFG_I2C_8574_ADDR1}, \
+ {1, CFG_I2C_8574_ADDR2}, \
+ {1, CFG_I2C_8574A_ADDR1}, \
+ {1, CFG_I2C_8574A_ADDR2}}
+/* Bit definitions for the 8574[A] I2C expander */
+#define I2C_8574_REVISION 0x03 /* Board revision, 00=0.0, 01=0.1, 10=1.0 */
+#define I2C_8574_CF 0x08 /* 1=Compact flash absent, 0=present */
+#define I2C_8574_MPCICLKRN 0x10 /* MiniPCI Clk Run */
+#define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */
+#define I2C_8574_FLASHSIDE 0x40 /* 0=Reset vector from U4, 1=from U7*/
+
+#undef CONFIG_SOFT_I2C
+
+#endif
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define PCI_66M
+#ifdef PCI_66M
+#define CONFIG_83XX_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#ifdef PCI_66M
+#define CONFIG_SYS_CLK_FREQ 66666666
+#else
+#define CONFIG_SYS_CLK_FREQ 33333333
+#endif
+#endif
+
+#define CFG_IMMRBAR 0xE0000000 /* The IMMR is relocated to here */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00003000 /* memtest region */
+#define CFG_MEMTEST_END 0x07100000 /* only has 128M */
+
+/*
+ * DDR Setup
+ */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#undef CONFIG_DDR_2T_TIMING
+#define CFG_83XX_DDR_USES_CS0
+
+#ifndef CONFIG_SPD_EEPROM
+/*
+ * Manually set up DDR parameters
+ */
+ #define CFG_DDR_SIZE 256 /* Mb */
+ #define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+
+ #define CFG_DDR_TIMING_1 0x26242321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */
+#endif
+
+/* FLASH on the Local Bus */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 16 /* FLASH size in MB */
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V)
+#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16Mb window bytes */
+
+/* VSC7385 on the Local Bus */
+#define CFG_VSC7385_BASE 0xF8000000 /* start of VSC7385 */
+
+#define CFG_BR1_PRELIM (CFG_VSC7385_BASE | BR_PS_8 | BR_V)
+#define CFG_OR1_PRELIM (0xFFFE0000 /* 128KB */ | \
+ OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_SETA | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CFG_LBLAWBAR1_PRELIM CFG_VSC7385_BASE /* Access window base at VSC7385 base */
+#define CFG_LBLAWAR1_PRELIM 0x80000010 /* Access window size 128K */
+
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE + 0x800000}
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_LED_BASE 0xF9000000 /* start of LED and Board ID */
+#define CFG_BR2_PRELIM (CFG_LED_BASE | BR_PS_8 | BR_V)
+#define CFG_OR2_PRELIM (0xFFE00000 /* 2MB */ | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | \
+ OR_GPCM_SCY_9 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#ifdef CONFIG_COMPACT_FLASH
+
+#define CFG_CF_BASE 0xF0000000
+
+#define CFG_BR3_PRELIM (CFG_CF_BASE | BR_PS_16 | BR_MS_UPMA | BR_V)
+#define CFG_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
+
+#define CFG_LBLAWBAR2_PRELIM CFG_CF_BASE /* Window base at flash base + LED & Board ID */
+#define CFG_LBLAWAR2_PRELIM 0x8000000F /* 64K bytes */
+
+#undef CONFIG_IDE_RESET
+#undef CONFIG_IDE_PREINIT
+
+#define CFG_IDE_MAXBUS 1
+#define CFG_IDE_MAXDEVICE 1
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR CFG_CF_BASE
+#define CFG_ATA_DATA_OFFSET 0x0000
+#define CFG_ATA_REG_OFFSET 0
+#define CFG_ATA_ALT_OFFSET 0x0200
+#define CFG_ATA_STRIDE 2
+
+#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
+
+#endif
+
+#define CONFIG_DOS_PARTITION
+
+#define CFG_MID_FLASH_JUMP 0x7F000000
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ * LCRR: DLL bypass, Clock divider is 4
+ * External Local Bus rate is
+ * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
+ */
+#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CFG_LBC_LBCR 0x00000000
+
+#undef CFG_LB_SDRAM /* if board has SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+/*local bus BR2, OR2 definition for SDRAM if soldered on the ADS board*/
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
+ */
+
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+#define CFG_LBLAWBAR2_PRELIM 0xF0000000
+#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64M */
+
+#define CFG_BR2_PRELIM (CFG_LBC_SDRAM_BASE | BR_PS_32 | BR_MS_SDRAM | BR_V)
+#define CFG_OR2_PRELIM (0xFC000000 /* 64 MB */ | \
+ OR_SDRAM_XAM | \
+ ((9 - 7) << OR_SDRAM_COLS_SHIFT) | \
+ ((13 - 9) << OR_SDRAM_ROWS_SHIFT) | \
+ OR_SDRAM_EAD)
+
+#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR8 (5 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT6 (5 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC3 (3 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFEN \
+ | CFG_LBC_LSDMR_BSMA1516 \
+ | CFG_LBC_LSDMR_RFCR8 \
+ | CFG_LBC_LSDMR_PRETOACT6 \
+ | CFG_LBC_LSDMR_ACTTORW3 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC3 \
+ | CFG_LBC_LSDMR_CL3 \
+ )
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL)
+#endif
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMRBAR + 0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMRBAR + 0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_MPC83XX_PCI2
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE (CFG_PCI1_MEM_BASE + CFG_PCI1_MEM_SIZE)
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xE2000000
+#define CFG_PCI1_IO_SIZE 0x01000000 /* 16M */
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_PCI2_MEM_BASE (CFG_PCI1_MMIO_BASE + CFG_PCI1_MMIO_SIZE)
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_MMIO_BASE (CFG_PCI2_MEM_BASE + CFG_PCI2_MEM_SIZE)
+#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE
+#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS (CFG_PCI1_IO_PHYS + CFG_PCI1_IO_SIZE)
+#define CFG_PCI2_IO_SIZE 0x01000000 /* 16M */
+#endif
+
+#define _IO_BASE 0x00000000 /* points to PCI I/O space */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x) (x)
+#endif
+
+#ifndef CONFIG_PCI_PNP
+ #define PCI_ENET0_IOADDR 0x00000000
+ #define PCI_ENET0_MEMADDR CFG_PCI2_MEM_BASE
+ #define PCI_IDSEL_NUMBER 0x0f /* IDSEL = AD15 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#endif
+
+/* TSEC */
+
+#ifdef CONFIG_TSEC_ENET
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII
+#define CONFIG_PHY_GIGE /* In case CFG_CMD_MII is specified */
+
+#define CONFIG_MPC83XX_TSEC1
+
+#ifdef CONFIG_MPC83XX_TSEC1
+#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
+#define CFG_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
+#define CFG_TSEC2_OFFSET 0x25000
+#define CONFIG_UNKNOWN_TSEC /* TSEC2 is proprietary */
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_PHYIDX 0
+#endif
+
+#define CONFIG_ETHPRIME "Freescale TSEC"
+
+#endif
+
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/* CONFIG_COMMANDS */
+
+#ifdef CONFIG_COMPACT_FLASH
+#define CONFIG_COMMANDS_CF (CFG_CMD_IDE | CFG_CMD_FAT)
+#else
+#define CONFIG_COMMANDS_CF 0
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_COMMANDS_PCI CFG_CMD_PCI
+#else
+#define CONFIG_COMMANDS_PCI 0
+#endif
+
+#ifdef CONFIG_HARD_I2C
+#define CONFIG_COMMANDS_I2C CFG_CMD_I2C
+#else
+#define CONFIG_COMMANDS_I2C 0
+#endif
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CONFIG_COMMANDS_CF | \
+ CFG_CMD_NET | \
+ CFG_CMD_PING | \
+ CONFIG_COMMANDS_I2C | \
+ CONFIG_COMMANDS_PCI | \
+ CFG_CMD_SDRAM | \
+ CFG_CMD_DATE | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_IRQ)
+#include <cmd_confdefs.h>
+
+/* Watchdog */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#ifdef CONFIG_WATCHDOG
+#define CFG_WATCHDOG_VALUE 0xFFFFFFC3
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log2 of the above value */
+#endif
+
+#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#define CFG_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN_4X1 |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#ifdef PCI_64BIT
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_64_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII )
+#else
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_32_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII )
+#endif
+
+/* System performance */
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CFG_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
+#define CFG_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
+#define CFG_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
+#define CFG_SCCR_TSEC2CM 1 /* TSEC2 & I2C1 clock mode (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count */
+
+/* System IO Config */
+#define CFG_SICRH SICRH_TSOBI1 /* Needed for gigabit to work on TSEC 1 */
+#define CFG_SICRL SICRL_LDP_A
+
+#define CFG_HID0_INIT 0x000000000
+
+#define CFG_HID0_FINAL CFG_HID0_INIT
+
+#define CFG_HID2 HID2_HBE
+
+/* DDR @ 0x00000000 */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#ifdef CONFIG_PCI
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT1L 0
+#define CFG_IBAT1U 0
+#define CFG_IBAT2L 0
+#define CFG_IBAT2U 0
+#endif
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CFG_IBAT3L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT4U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L 0
+#define CFG_IBAT3U 0
+#define CFG_IBAT4L 0
+#define CFG_IBAT4U 0
+#endif
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CFG_IBAT5L (CFG_IMMRBAR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMRBAR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT7L 0
+#define CFG_IBAT7U 0
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_MPC83XX_TSEC1
+#define CONFIG_ETHADDR 00:E0:0C:00:8C:01
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:8C:02
+#endif
+
+#define CONFIG_IPADDR 10.82.19.159
+#define CONFIG_SERVERIP 10.82.48.106
+#define CONFIG_GATEWAYIP 10.82.19.254
+#define CONFIG_NETMASK 255.255.252.0
+
+
+#define CONFIG_HOSTNAME mpc8349emitx
+#define CONFIG_ROOTPATH /nfsroot0/u/timur/itx-ltib/rootfs
+#define CONFIG_BOOTFILE timur/uImage
+
+#define CONFIG_UBOOTPATH timur/u-boot.bin
+#define CONFIG_UBOOTSTART fe700000
+#define CONFIG_UBOOTEND fe77ffff
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BAUDRATE 115200
+
+#undef CONFIG_BOOTCOMMAND
+#ifdef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTDELAY 6
+#else
+#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#endif
+
+#define CONFIG_BOOTARGS \
+ "root=/dev/nfs rw nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=ttyS0,$baudrate $othbootargs"
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "tftpflash=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
+ "erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
+ "cp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize; " \
+ "cmp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize\0" \
+ "tftpupdate=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
+ "protect off FEF00000 FEF7FFFF; " \
+ "erase FEF00000 FEF7FFFF; " \
+ "cp.b $loadaddr FEF00000 $filesize; " \
+ "protect on FEF00000 FEF7FFFF; " \
+ "cmp.b $loadaddr FEF00000 $filesize\0" \
+ "tftplinux=tftpboot $loadaddr $bootfile; bootm\0" \
+ "copyuboot=erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
+ "cp.b fef00000 " MK_STR(CONFIG_UBOOTSTART) " 80000\0"
+
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif
projects / karo-tx-uboot.git / commitdiff