+/**************************************************************************
+Etherboot - BOOTP/TFTP Bootstrap Program
+Skeleton NIC driver for Etherboot
+***************************************************************************/
+
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2, or (at
+ * your option) any later version.
+ */
+
+/*
+ * This file is a modified version from the Galileo polled mode
+ * network driver for the ethernet contained within the GT64260
+ * chip. It has been modified to fit into the U-Boot framework, from
+ * the original (etherboot) setup. Also, additional cleanup and features
+ * were added.
+ *
+ * - Josh Huber <huber@mclx.com>
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <cmd_bsp.h>
+#include <galileo/gt64260R.h>
+#include <galileo/core.h>
+#include <asm/cache.h>
+#include <miiphy.h>
+#include <net.h>
+
+#include "eth.h"
+#include "eth_addrtbl.h"
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI)
+
+#define GT6426x_ETH_BUF_SIZE 1536
+
+/* if you like verbose output, turn this on! */
+#undef DEBUG
+
+/* Restart autoneg if we detect link is up on phy init. */
+
+/*
+ * The GT doc's say that after Rst is deasserted, and the PHY
+ * reports autoneg complete, it runs through its autoneg
+ * procedures. This doesn't seem to be the case for MII
+ * PHY's. To work around this check for link up && autoneg
+ * complete when initilizing the port. If they are both set,
+ * then restart PHY autoneg. Of course, it may be something
+ * completly different.
+ */
+#ifdef CONFIG_ETHER_PORT_MII
+# define RESTART_AUTONEG
+#endif
+
+/* do this if you dont want to use snooping */
+#define USE_SOFTWARE_CACHE_MANAGEMENT
+
+#ifdef USE_SOFTWARE_CACHE_MANAGEMENT
+#define FLUSH_DCACHE(a,b) if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));}
+#define FLUSH_AND_INVALIDATE_DCACHE(a,b) if(dcache_status()){flush_dcache_range((u32)(a),(u32)(b));}
+#define INVALIDATE_DCACHE(a,b) if(dcache_status()){invalidate_dcache_range((u32)(a),(u32)(b));}
+#else
+/* bummer - w/o flush, nothing works, even with snooping - FIXME */
+/* #define FLUSH_DCACHE(a,b) */
+#define FLUSH_DCACHE(a,b) if(dcache_status()){clean_dcache_range((u32)(a),(u32)(b));}
+#define FLUSH_AND_INVALIDATE_DCACHE(a,b)
+#define INVALIDATE_DCACHE(a,b)
+#endif
+struct eth_dev_s {
+ eth0_tx_desc_single *eth_tx_desc;
+ eth0_rx_desc_single *eth_rx_desc;
+ char *eth_tx_buffer;
+ char *eth_rx_buffer[NR];
+ int tdn, rdn;
+ int dev;
+ unsigned int reg_base;
+};
+
+
+#ifdef CONFIG_INTEL_LXT97X
+/* for intel LXT972 */
+static const char ether_port_phy_addr[3]={0,1,2};
+#else
+static const char ether_port_phy_addr[3]={4,5,6};
+#endif
+
+
+static inline unsigned short
+miiphy_read_ret(unsigned short phy, unsigned short reg)
+{
+ unsigned short val;
+ miiphy_read(phy,reg,&val);
+ return val;
+}
+
+
+/**************************************************************************
+RESET - Reset adapter
+***************************************************************************/
+void
+gt6426x_eth_reset(void *v)
+{
+ /* we should do something here...
+ struct eth_device *wp = (struct eth_device *)v;
+ struct eth_dev_s *p = wp->priv;
+ */
+
+ printf ("RESET\n");
+ /* put the card in its initial state */
+}
+
+static void gt6426x_handle_SMI(struct eth_dev_s *p, unsigned int icr)
+{
+#ifdef DEBUG
+ printf("SMI interrupt: ");
+
+ if(icr&0x20000000) {
+ printf("SMI done\n");
+ }
+#endif
+
+ if(icr&0x10000000) {
+ unsigned int psr;
+ psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base);
+#ifdef DEBUG
+ printf("PHY state change:\n"
+ " GT:%s:%s:%s:%s\n",
+ psr&1?"100":" 10",
+ psr&8?" Link":"nLink",
+ psr&2?"FD":"HD",
+ psr&4?" FC":"nFC");
+
+#ifdef CONFIG_INTEL_LXT97X /* non-standard mii reg (intel lxt972a) */
+ {
+ unsigned short mii_11;
+ mii_11=miiphy_read_ret(ether_port_phy_addr[p->dev],0x11);
+
+ printf(" mii:%s:%s:%s:%s %s:%s %s\n",
+ mii_11&(1<<14)?"100":" 10",
+ mii_11&(1<<10)?" Link":"nLink",
+ mii_11&(1<<9)?"FD":"HD",
+ mii_11&(1<<4)?" FC":"nFC",
+
+ mii_11&(1<<7)?"ANc":"ANnc",
+ mii_11&(1<<8)?"AN":"Manual",
+ ""
+ );
+ }
+#endif /* CONFIG_INTEL_LXT97X */
+#endif /* DEBUG */
+ }
+}
+
+static int
+gt6426x_eth_receive(struct eth_dev_s *p,unsigned int icr)
+{
+ int eth_len=0;
+ char *eth_data;
+
+ eth0_rx_desc_single *rx=&p->eth_rx_desc[(p->rdn)];
+
+ INVALIDATE_DCACHE((unsigned int)rx,(unsigned int)(rx+1));
+
+ if (rx->command_status & 0x80000000) {
+ return 0; /* No packet received */
+ }
+
+ eth_len = (unsigned int)
+ (rx->buff_size_byte_count) & 0x0000ffff;
+ eth_data = (char *) p->eth_rx_buffer[p->rdn];
+
+#ifdef DEBUG
+ if (eth_len) {
+ printf ("%s: Recived %d byte Packet @ 0x%p\n",
+ __FUNCTION__, eth_len, eth_data);
+ }
+#endif
+ /*
+ * packet is now in:
+ * eth0_rx_buffer[RDN_ETH0];
+ */
+
+ /* let the upper layer handle the packet */
+ NetReceive (eth_data, eth_len);
+
+ rx->buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16;
+
+
+ /* GT96100 Owner */
+ rx->command_status = 0x80000000;
+
+ FLUSH_DCACHE((unsigned int)rx,(unsigned int)(rx+1));
+
+ p->rdn ++;
+ if (p->rdn == NR) {p->rdn = 0;}
+
+ sync();
+
+ /* Start Rx*/
+ GT_REG_WRITE (ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x00000080);
+
+#ifdef DEBUG
+ {
+ int i;
+ for (i=0;i<12;i++) {
+ printf(" %02x", eth_data[i]);
+ }
+ }
+ printf(": %d bytes\n", eth_len);
+#endif
+ INVALIDATE_DCACHE((unsigned int)eth_data,
+ (unsigned int)eth_data+eth_len);
+ return eth_len;
+}
+
+/**************************************************************************
+POLL - look for an rx frame, handle other conditions
+***************************************************************************/
+int
+gt6426x_eth_poll(void *v)
+{
+ struct eth_device *wp = (struct eth_device *)v;
+ struct eth_dev_s *p = wp->priv;
+ unsigned int icr=GTREGREAD(ETHERNET0_INTERRUPT_CAUSE_REGISTER + p->reg_base);
+
+ if(icr) {
+ GT_REG_WRITE(ETHERNET0_INTERRUPT_CAUSE_REGISTER +p->reg_base, 0);
+#ifdef DEBUG
+ printf("poll got ICR %08x\n", icr);
+#endif
+ /* SMI done or PHY state change*/
+ if(icr&0x30000000) gt6426x_handle_SMI(p, icr);
+ }
+ /* always process. We aren't using RX interrupts */
+ return gt6426x_eth_receive(p, icr);
+}
+
+/**************************************************************************
+TRANSMIT - Transmit a frame
+***************************************************************************/
+int
+gt6426x_eth_transmit(void *v, volatile char *p, unsigned int s)
+{
+ struct eth_device *wp = (struct eth_device *)v;
+ struct eth_dev_s *dev = (struct eth_dev_s *)wp->priv;
+#ifdef DEBUG
+ unsigned int old_command_stat,old_psr;
+#endif
+ eth0_tx_desc_single *tx=&dev->eth_tx_desc[dev->tdn];
+
+ /* wait for tx to be ready */
+ INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1));
+ while (tx->command_status & 0x80000000) {
+ int i;
+ for(i=0;i<1000;i++);
+ INVALIDATE_DCACHE((unsigned int)tx,(unsigned int)(tx+1));
+ }
+
+ GT_REG_WRITE (ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + dev->reg_base,
+ (unsigned int)tx);
+
+#ifdef DEBUG
+ printf("copying to tx_buffer [%p], length %x, desc = %p\n",
+ dev->eth_tx_buffer, s, dev->eth_tx_desc);
+#endif
+ memcpy(dev->eth_tx_buffer, (char *) p, s);
+
+ tx->buff_pointer = dev->eth_tx_buffer;
+ tx->bytecount_reserved = ((__u16)s) << 16;
+
+ /* 31 - own
+ * 22 - gencrc
+ * 18:16 - pad, last, first */
+ tx->command_status = (1<<31) | (1<<22) | (7<<16);
+#if 0
+ /* FEr #18 */
+ tx->next_desc = NULL;
+#else
+ tx->next_desc =
+ (struct eth0_tx_desc_struct *)
+ &dev->eth_tx_desc[(dev->tdn+1)%NT].bytecount_reserved;
+
+ /* cpu owned */
+ dev->eth_tx_desc[(dev->tdn+1)%NT].command_status = (7<<16); /* pad, last, first */
+#endif
+
+#ifdef DEBUG
+ old_command_stat=tx->command_status,
+ old_psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base);
+#endif
+
+ FLUSH_DCACHE((unsigned int)tx,
+ (unsigned int)&dev->eth_tx_desc[(dev->tdn+2)%NT]);
+
+ FLUSH_DCACHE((unsigned int)dev->eth_tx_buffer,(unsigned int)dev->eth_tx_buffer+s);
+
+ GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + dev->reg_base, 0x01000000);
+
+#ifdef DEBUG
+ {
+ unsigned int command_stat=0;
+ printf("cmd_stat: %08x PSR: %08x\n", old_command_stat, old_psr);
+ /* wait for tx to be ready */
+ do {
+ unsigned int psr=GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + dev->reg_base);
+ command_stat=tx->command_status;
+ if(command_stat!=old_command_stat || psr !=old_psr) {
+ printf("cmd_stat: %08x PSR: %08x\n", command_stat, psr);
+ old_command_stat = command_stat;
+ old_psr = psr;
+ }
+ /* gt6426x_eth0_poll(); */
+ } while (command_stat & 0x80000000);
+
+ printf("sent %d byte frame\n", s);
+
+ if((command_stat & (3<<15)) == 3) {
+ printf("frame had error (stat=%08x)\n", command_stat);
+ }
+ }
+#endif
+ return 0;
+}
+
+/**************************************************************************
+DISABLE - Turn off ethernet interface
+***************************************************************************/
+void
+gt6426x_eth_disable(void *v)
+{
+ struct eth_device *wp = (struct eth_device *)v;
+ struct eth_dev_s *p = (struct eth_dev_s *)wp->priv;
+
+ GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + p->reg_base, 0x80008000);
+}
+
+/**************************************************************************
+MII utilities - write: write to an MII register via SMI
+***************************************************************************/
+int
+miiphy_write(unsigned char phy, unsigned char reg,
+ unsigned short data)
+{
+ unsigned int temp= (reg<<21) | (phy<<16) | data;
+
+ while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28)); /* wait for !Busy */
+
+ GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp);
+ return 0;
+}
+
+/**************************************************************************
+MII utilities - read: read from an MII register via SMI
+***************************************************************************/
+int
+miiphy_read(unsigned char phy, unsigned char reg,
+ unsigned short *val)
+{
+ unsigned int temp= (reg<<21) | (phy<<16) | 1<<26;
+
+ while(GTREGREAD(ETHERNET_SMI_REGISTER) & (1<<28)); /* wait for !Busy */
+
+ GT_REG_WRITE(ETHERNET_SMI_REGISTER, temp);
+
+ while(1) {
+ temp=GTREGREAD(ETHERNET_SMI_REGISTER);
+ if(temp & (1<<27)) break; /* wait for ReadValid */
+ }
+ *val = temp & 0xffff;
+
+ return 0;
+}
+
+#ifdef DEBUG
+/**************************************************************************
+MII utilities - dump mii registers
+***************************************************************************/
+static void
+gt6426x_dump_mii(bd_t *bis, unsigned short phy)
+{
+ printf("mii reg 0 - 3: %04x %04x %04x %04x\n",
+ miiphy_read_ret(phy, 0x0),
+ miiphy_read_ret(phy, 0x1),
+ miiphy_read_ret(phy, 0x2),
+ miiphy_read_ret(phy, 0x3)
+ );
+ printf(" 4 - 7: %04x %04x %04x %04x\n",
+ miiphy_read_ret(phy, 0x4),
+ miiphy_read_ret(phy, 0x5),
+ miiphy_read_ret(phy, 0x6),
+ miiphy_read_ret(phy, 0x7)
+ );
+ printf(" 8: %04x\n",
+ miiphy_read_ret(phy, 0x8)
+ );
+ printf(" 16-19: %04x %04x %04x %04x\n",
+ miiphy_read_ret(phy, 0x10),
+ miiphy_read_ret(phy, 0x11),
+ miiphy_read_ret(phy, 0x12),
+ miiphy_read_ret(phy, 0x13)
+ );
+ printf(" 20,30: %04x %04x\n",
+ miiphy_read_ret(phy, 20),
+ miiphy_read_ret(phy, 30)
+ );
+}
+#endif
+
+#ifdef RESTART_AUTONEG
+
+/* If link is up && autoneg compleate, and if
+ * GT and PHY disagree about link capabilitys,
+ * restart autoneg - something screwy with FD/HD
+ * unless we do this. */
+static void
+check_phy_state(struct eth_dev_s *p)
+{
+ int bmsr = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_BMSR);
+ int psr = GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + p->reg_base);
+
+ if ((psr & 1<<3) && (bmsr & PHY_BMSR_LS)) {
+ int nego = miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANAR) &
+ miiphy_read_ret(ether_port_phy_addr[p->dev], PHY_ANLPAR);
+ int want;
+
+ if (nego & PHY_ANLPAR_TXFD) {
+ want = 0x3;
+ printf("MII: 100Base-TX, Full Duplex\n");
+ } else if (nego & PHY_ANLPAR_TX) {
+ want = 0x1;
+ printf("MII: 100Base-TX, Half Duplex\n");
+ } else if (nego & PHY_ANLPAR_10FD) {
+ want = 0x2;
+ printf("MII: 10Base-T, Full Duplex\n");
+ } else if (nego & PHY_ANLPAR_10) {
+ want = 0x0;
+ printf("MII: 10Base-T, Half Duplex\n");
+ } else {
+ printf("MII: Unknown link-foo! %x\n", nego);
+ return;
+ }
+
+ if ((psr & 0x3) != want) {
+ printf("MII: GT thinks %x, PHY thinks %x, restarting autoneg..\n",
+ psr & 0x3, want);
+ miiphy_write(ether_port_phy_addr[p->dev],0,
+ miiphy_read_ret(ether_port_phy_addr[p->dev],0) | (1<<9));
+ udelay(10000); /* the EVB's GT takes a while to notice phy
+ went down and up */
+ }
+ }
+}
+#endif
+
+/**************************************************************************
+PROBE - Look for an adapter, this routine's visible to the outside
+***************************************************************************/
+int
+gt6426x_eth_probe(void *v, bd_t *bis)
+{
+ struct eth_device *wp = (struct eth_device *)v;
+ struct eth_dev_s *p = (struct eth_dev_s *)wp->priv;
+ int dev = p->dev;
+ unsigned int reg_base = p->reg_base;
+ unsigned long temp;
+ int i;
+
+ if (( dev < 0 ) || ( dev >= GAL_ETH_DEVS ))
+ { /* This should never happen */
+ printf("%s: Invalid device %d\n", __FUNCTION__, dev );
+ return 0;
+ }
+
+#ifdef DEBUG
+ printf ("%s: initializing %s\n", __FUNCTION__, wp->name );
+ printf ("\nCOMM_CONTROL = %08x , COMM_CONF = %08x\n",
+ GTREGREAD(COMM_UNIT_ARBITER_CONTROL),
+ GTREGREAD(COMM_UNIT_ARBITER_CONFIGURATION_REGISTER));
+#endif
+
+ /* clear MIB counters */
+ for(i=0;i<255; i++)
+ temp=GTREGREAD(ETHERNET0_MIB_COUNTER_BASE + reg_base +i);
+
+#ifdef CONFIG_INTEL_LXT97X
+ /* for intel LXT972 */
+
+ /* led 1: 0x1=txact
+ led 2: 0xc=link/rxact
+ led 3: 0x2=rxact (N/C)
+ strch: 0,2=30 ms, enable */
+ miiphy_write(ether_port_phy_addr[p->dev], 20, 0x1c22);
+
+ /* 2.7ns port rise time */
+ /*miiphy_write(ether_port_phy_addr[p->dev], 30, 0x0<<10); */
+#else
+ /* already set up in mpsc.c */
+ /*GT_REG_WRITE(MAIN_ROUTING_REGISTER, 0x7ffe38); / b400 */
+
+ /* already set up in sdram_init.S... */
+ /* MPSC0, MPSC1, RMII */
+ /*GT_REG_WRITE(SERIAL_PORT_MULTIPLEX, 0x1102); / f010 */
+#endif
+ GT_REG_WRITE(ETHERNET_PHY_ADDRESS_REGISTER,
+ ether_port_phy_addr[0] |
+ (ether_port_phy_addr[1]<<5) |
+ (ether_port_phy_addr[2]<<10)); /* 2000 */
+
+ /* 13:12 - 10: 4x64bit burst (cache line size = 32 bytes)
+ * 9 - 1: RIFB - interrupt on frame boundaries only
+ * 6:7 - 00: big endian rx and tx
+ * 5:2 - 1111: 15 retries */
+ GT_REG_WRITE(ETHERNET0_SDMA_CONFIGURATION_REGISTER + reg_base,
+ (2<<12) | (1<<9) | (0xf<<2) ); /* 2440 */
+
+#ifndef USE_SOFTWARE_CACHE_MANAGEMENT
+ /* enable rx/tx desc/buffer cache snoop */
+ GT_REG_READ(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20,
+ &temp); /* f200 */
+ temp|= (1<<6)| (1<<14)| (1<<22)| (1<<30);
+ GT_REG_WRITE(ETHERNET_0_ADDRESS_CONTROL_LOW + dev*0x20,
+ temp);
+#endif
+
+ /* 31 28 27 24 23 20 19 16
+ * 0000 0000 0000 0000 [0004]
+ * 15 12 11 8 7 4 3 0
+ * 1000 1101 0000 0000 [4d00]
+ * 20 - 0=MII 1=RMII
+ * 19 - 0=speed autoneg
+ * 15:14 - framesize 1536 (GT6426x_ETH_BUF_SIZE)
+ * 11 - no force link pass
+ * 10 - 1=disable fctl autoneg
+ * 8 - override prio ?? */
+ temp = 0x00004d00;
+#ifndef CONFIG_ETHER_PORT_MII
+ temp |= (1<<20); /* RMII */
+#endif
+ /* set En */
+ GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + reg_base,
+ temp); /* 2408 */
+
+ /* hardcode E1 also? */
+ /* -- according to dox, this is safer due to extra pulldowns? */
+ if (dev<2) {
+ GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_EXTEND_REGISTER + (dev+1) * 0x400,
+ temp); /* 2408 */
+ }
+
+ /* wake up MAC */ /* 2400 */
+ GT_REG_READ(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, &temp);
+ temp |= (1<<7); /* enable port */
+#ifdef CONFIG_GT_USE_MAC_HASH_TABLE
+ temp |= (1<<12); /* hash size 1/2k */
+#else
+ temp |= 1; /* promisc */
+#endif
+ GT_REG_WRITE(ETHERNET0_PORT_CONFIGURATION_REGISTER + reg_base, temp);
+ /* 2400 */
+
+#ifdef RESTART_AUTONEG
+ check_phy_state(p);
+#endif
+
+ printf("%s: Waiting for link up..\n", wp->name);
+ temp = 10 * 1000;
+ /* wait for link back up */
+ while(!(GTREGREAD(ETHERNET0_PORT_STATUS_REGISTER + reg_base) & 8)
+ && (--temp > 0)){
+ udelay(1000); /* wait 1 ms */
+ }
+ if ( temp == 0) {
+ printf("%s: Failed!\n", wp->name);
+ return (0);
+ }
+
+ printf("%s: OK!\n", wp->name);
+
+ p->tdn = 0;
+ p->rdn = 0;
+ p->eth_tx_desc[p->tdn].command_status = 0;
+
+ /* Initialize Rx Side */
+ for (temp = 0; temp < NR; temp++) {
+ p->eth_rx_desc[temp].buff_pointer = p->eth_rx_buffer[temp];
+ p->eth_rx_desc[temp].buff_size_byte_count = GT6426x_ETH_BUF_SIZE<<16;
+
+ /* GT96100 Owner */
+ p->eth_rx_desc[temp].command_status = 0x80000000;
+ p->eth_rx_desc[temp].next_desc =
+ (struct eth0_rx_desc_struct *)
+ &p->eth_rx_desc[(temp+1)%NR].buff_size_byte_count;
+ }
+
+ FLUSH_DCACHE((unsigned int)&p->eth_tx_desc[0],
+ (unsigned int)&p->eth_tx_desc[NR]);
+ FLUSH_DCACHE((unsigned int)&p->eth_rx_desc[0],
+ (unsigned int)&p->eth_rx_desc[NR]);
+
+ GT_REG_WRITE(ETHERNET0_CURRENT_TX_DESCRIPTOR_POINTER0 + reg_base,
+ (unsigned int) p->eth_tx_desc);
+ GT_REG_WRITE(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base,
+ (unsigned int) p->eth_rx_desc);
+ GT_REG_WRITE(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base,
+ (unsigned int) p->eth_rx_desc);
+
+#ifdef DEBUG
+ printf ("\nRx descriptor pointer is %08x %08x\n",
+ GTREGREAD(ETHERNET0_FIRST_RX_DESCRIPTOR_POINTER0 + reg_base),
+ GTREGREAD(ETHERNET0_CURRENT_RX_DESCRIPTOR_POINTER0 + reg_base));
+ printf ("\n\n%08x %08x\n",
+ (unsigned int)p->eth_rx_desc,p->eth_rx_desc[0].command_status);
+
+ printf ("Descriptor dump:\n");
+ printf ("cmd status: %08x\n",p->eth_rx_desc[0].command_status);
+ printf ("byte_count: %08x\n",p->eth_rx_desc[0].buff_size_byte_count);
+ printf ("buff_ptr: %08x\n",(unsigned int)p->eth_rx_desc[0].buff_pointer);
+ printf ("next_desc: %08x\n\n",(unsigned int)p->eth_rx_desc[0].next_desc);
+ printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x0));
+ printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x4));
+ printf ("%08x\n",*(unsigned int *) ((unsigned int)p->eth_rx_desc + 0x8));
+ printf ("%08x\n\n",
+ *(unsigned int *) ((unsigned int)p->eth_rx_desc + 0xc));
+#endif
+
+#ifdef DEBUG
+ gt6426x_dump_mii(bis,ether_port_phy_addr[p->dev]);
+#endif
+
+#ifdef CONFIG_GT_USE_MAC_HASH_TABLE
+ {
+ unsigned int hashtable_base;
+ u8 *b = (u8 *)(wp->enetaddr);
+ u32 macH, macL;
+
+ /* twist the MAC up into the way the discovery wants it */
+ macH= (b[0]<<8) | b[1];
+ macL= (b[2]<<24) | (b[3]<<16) | (b[4]<<8) | b[5];
+
+ /* mode 0, size 0x800 */
+ hashtable_base =initAddressTable(dev,0,1);
+
+ if(!hashtable_base) {
+ printf("initAddressTable failed\n");
+ return 0;
+ }
+
+ addAddressTableEntry(dev, macH, macL, 1, 0);
+ GT_REG_WRITE(ETHERNET0_HASH_TABLE_POINTER_REGISTER + reg_base,
+ hashtable_base);
+ }
+#endif
+
+ /* Start Rx*/
+ GT_REG_WRITE(ETHERNET0_SDMA_COMMAND_REGISTER + reg_base, 0x00000080);
+ printf("%s: gt6426x eth device %d init success \n", wp->name, dev );
+ return 1;
+}
+
+/* enter all the galileo ethernet devs into MULTI-BOOT */
+void
+gt6426x_eth_initialize(bd_t *bis)
+{
+ struct eth_device *dev;
+ struct eth_dev_s *p;
+ int devnum, x, temp;
+ char *s, *e, buf[64];
+
+#ifdef DEBUG
+ printf( "\n%s\n", __FUNCTION );
+#endif
+
+ for (devnum = 0; devnum < GAL_ETH_DEVS; devnum++) {
+ dev = calloc(sizeof(*dev), 1);
+ if (!dev) {
+ printf( "%s: gal_enet%d allocation failure, %s\n",
+ __FUNCTION__, devnum, "eth_device structure");
+ return;
+ }
+
+ /* must be less than NAMESIZE (16) */
+ sprintf(dev->name, "gal_enet%d", devnum);
+
+#ifdef DEBUG
+ printf( "Initializing %s\n", dev->name );
+#endif
+
+ /* Extract the MAC address from the environment */
+ switch (devnum)
+ {
+ case 0: s = "ethaddr"; break;
+#if (GAL_ETH_DEVS > 1)
+ case 1: s = "eth1addr"; break;
+#endif
+#if (GAL_ETH_DEVS > 2)
+ case 2: s = "eth2addr"; break;
+#endif
+ default: /* this should never happen */
+ printf( "%s: Invalid device number %d\n",
+ __FUNCTION__, devnum );
+ return;
+ }
+
+ temp = getenv_r (s, buf, sizeof(buf));
+ s = (temp > 0) ? buf : NULL;
+
+#ifdef DEBUG
+ printf ("Setting MAC %d to %s\n", devnum, s );
+#endif
+ for (x = 0; x < 6; ++x) {
+ dev->enetaddr[x] = s ? simple_strtoul(s, &e, 16) : 0;
+ if (s)
+ s = (*e) ? e+1 : e;
+ }
+
+ dev->init = (void*)gt6426x_eth_probe;
+ dev->halt = (void*)gt6426x_eth_reset;
+ dev->send = (void*)gt6426x_eth_transmit;
+ dev->recv = (void*)gt6426x_eth_poll;
+
+ dev->priv = (void*)p = calloc( sizeof(*p), 1 );
+ if (!p)
+ {
+ printf( "%s: %s allocation failure, %s\n",
+ __FUNCTION__, dev->name, "Private Device Structure");
+ free(dev);
+ return;
+ }
+
+ p->dev = devnum;
+ p->tdn=0;
+ p->rdn=0;
+ p->reg_base = devnum * ETHERNET_PORTS_DIFFERENCE_OFFSETS;
+
+ p->eth_tx_desc =
+ (eth0_tx_desc_single *)
+ (((unsigned int) malloc(sizeof (eth0_tx_desc_single) *
+ (NT+1)) & 0xfffffff0) + 0x10);
+ if (!p)
+ {
+ printf( "%s: %s allocation failure, %s\n",
+ __FUNCTION__, dev->name, "Tx Descriptor");
+ free(dev);
+ return;
+ }
+
+ p->eth_rx_desc =
+ (eth0_rx_desc_single *)
+ (((unsigned int) malloc(sizeof (eth0_rx_desc_single) *
+ (NR+1)) & 0xfffffff0) + 0x10);
+ if (!p->eth_rx_desc)
+ {
+ printf( "%s: %s allocation failure, %s\n",
+ __FUNCTION__, dev->name, "Rx Descriptor");
+ free(dev);
+ free(p);
+ return;
+ }
+
+ p->eth_tx_buffer =
+ (char *) (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10);
+ if (!p->eth_tx_buffer)
+ {
+ printf( "%s: %s allocation failure, %s\n",
+ __FUNCTION__, dev->name, "Tx Bufffer");
+ free(dev);
+ free(p);
+ free(p->eth_rx_desc);
+ return;
+ }
+
+ for (temp = 0 ; temp < NR ; temp ++) {
+ p->eth_rx_buffer[temp] =
+ (char *)
+ (((unsigned int) malloc(GT6426x_ETH_BUF_SIZE) & 0xfffffff0) + 0x10);
+ if (!p->eth_rx_buffer[temp])
+ {
+ printf( "%s: %s allocation failure, %s\n",
+ __FUNCTION__, dev->name, "Rx Buffers");
+ free(dev);
+ free(p);
+ free(p->eth_tx_buffer);
+ free(p->eth_rx_desc);
+ free(p->eth_tx_desc);
+ while (temp >= 0)
+ free(p->eth_rx_buffer[--temp]);
+ return;
+ }
+ }
+
+
+ eth_register(dev);
+ }
+}
+#endif /* CFG_CMD_NET && CONFIG_NET_MULTI */
projects / karo-tx-uboot.git / commitdiff