bool "Support DB-88F6820-AMC"
select 88F6820
+config TARGET_MVEBU_DB_88F7040
+ bool "Support DB-88F7040 Armada 7040"
+ select ARMADA_8K
+
config TARGET_DB_MV784MP_GP
bool "Support db-mv784mp-gp"
select MV78460
default "db-88f6720" if TARGET_DB_88F6720
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
default "db-88f6820-amc" if TARGET_DB_88F6820_AMC
+ default "mvebu_db-88f7040" if TARGET_MVEBU_DB_88F7040
default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
default "ds414" if TARGET_DS414
default "maxbcm" if TARGET_MAXBCM
default "db-88f6720" if TARGET_DB_88F6720
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
default "db-88f6820-amc" if TARGET_DB_88F6820_AMC
+ default "mvebu_db-88f7040" if TARGET_MVEBU_DB_88F7040
default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
default "ds414" if TARGET_DS414
default "maxbcm" if TARGET_MAXBCM
default "Marvell" if TARGET_DB_88F6720
default "Marvell" if TARGET_DB_88F6820_GP
default "Marvell" if TARGET_DB_88F6820_AMC
+ default "Marvell" if TARGET_MVEBU_DB_88F7040
default "solidrun" if TARGET_CLEARFOG
default "Synology" if TARGET_DS414
--- /dev/null
+MVEBU_DB_88F7040 BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: board/Marvell/mvebu_db-88f7040/
+F: include/configs/mvebu_db-88f7040.h
+F: configs/mvebu_db-88f7040_defconfig
--- /dev/null
+#
+# Copyright (C) 2016 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := board.o
--- /dev/null
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* IO expander I2C device */
+#define I2C_IO_EXP_ADDR 0x21
+#define I2C_IO_CFG_REG_0 0x6
+#define I2C_IO_DATA_OUT_REG_0 0x2
+/* VBus enable */
+#define I2C_IO_REG_0_USB_H0_OFF 0
+#define I2C_IO_REG_0_USB_H1_OFF 1
+#define I2C_IO_REG_VBUS ((1 << I2C_IO_REG_0_USB_H0_OFF) | \
+ (1 << I2C_IO_REG_0_USB_H1_OFF))
+/* Current limit */
+#define I2C_IO_REG_0_USB_H0_CL 4
+#define I2C_IO_REG_0_USB_H1_CL 5
+#define I2C_IO_REG_CL ((1 << I2C_IO_REG_0_USB_H0_CL) | \
+ (1 << I2C_IO_REG_0_USB_H1_CL))
+
+static int usb_enabled = 0;
+
+/* Board specific xHCI dis-/enable code */
+
+/*
+ * Set USB VBUS signals (via I2C IO expander/GPIO) as output and set
+ * output value as disabled
+ *
+ * Set USB Current Limit signals (via I2C IO expander/GPIO) as output
+ * and set output value as enabled
+ */
+int board_xhci_config(void)
+{
+ struct udevice *dev;
+ int ret;
+ u8 buf[8];
+
+ /* Configure IO exander PCA9555: 7bit address 0x21 */
+ ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
+ if (ret) {
+ printf("Cannot find PCA9555: %d\n", ret);
+ return 0;
+ }
+
+ /*
+ * Read configuration (direction) and set VBUS pin as output
+ * (reset pin = output)
+ */
+ ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to read IO expander value via I2C\n");
+ return -EIO;
+ }
+ buf[0] &= ~I2C_IO_REG_VBUS;
+ buf[0] &= ~I2C_IO_REG_CL;
+ ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to set IO expander via I2C\n");
+ return -EIO;
+ }
+
+ /* Read output value and configure it */
+ ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to read IO expander value via I2C\n");
+ return -EIO;
+ }
+ buf[0] &= ~I2C_IO_REG_VBUS;
+ buf[0] |= I2C_IO_REG_CL;
+ ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to set IO expander via I2C\n");
+ return -EIO;
+ }
+
+ mdelay(500); /* required delay to let output value settle */
+
+ return 0;
+}
+
+int board_xhci_enable(void)
+{
+ struct udevice *dev;
+ int ret;
+ u8 buf[8];
+
+ /*
+ * This function enables all USB ports simultaniously,
+ * it only needs to get called once
+ */
+ if (usb_enabled)
+ return 0;
+
+ /* Configure IO exander PCA9555: 7bit address 0x21 */
+ ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
+ if (ret) {
+ printf("Cannot find PCA9555: %d\n", ret);
+ return 0;
+ }
+
+ /* Read VBUS output value */
+ ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to read IO expander value via I2C\n");
+ return -EIO;
+ }
+
+ /* Enable VBUS power: Set output value of VBUS pin as enabled */
+ buf[0] |= I2C_IO_REG_VBUS;
+ ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+ if (ret) {
+ printf("Failed to set IO expander via I2C\n");
+ return -EIO;
+ }
+
+ mdelay(500); /* required delay to let output value settle */
+ usb_enabled = 1;
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ /* Nothing to do (yet), perhaps later some pin-muxing etc */
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ /* Pre-configure the USB ports (overcurrent, VBus) */
+ board_xhci_config();
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MVEBU_DB_88F7040=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-7040-db"
+CONFIG_AHCI=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_BLOCK_CACHE=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_MISC=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PHYLIB=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+# CONFIG_SPL_SERIAL_PRESENT is not set
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xf0512000
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
--- /dev/null
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CONFIG_MVEBU_DB_88F7040_H
+#define _CONFIG_MVEBU_DB_88F7040_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_TEXT_BASE 0x00000000
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+
+#define CONFIG_NR_DRAM_BANKS 1
+
+/* auto boot */
+#define CONFIG_PREBOOT
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200, 230400, 460800, 921600 }
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
+
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4MiB for malloc() */
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */
+#define CONFIG_SYS_MEMTEST_END 0x00ffffff /*(_16M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* End of 16M scrubbed by training in bootrom */
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0xFF0000)
+
+/*
+ * SPI Flash configuration
+ */
+#define CONFIG_KIRKWOOD_SPI
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED 1000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+
+/* Environment in SPI NOR flash */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x180000 /* as Marvell U-Boot version */
+#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
+
+/* USB 2.0 */
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+
+/* USB 3.0 */
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3
+
+#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \
+ CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS)
+
+/* USB ethernet */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_RTL8152
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/*
+ * SATA/SCSI/AHCI configuration
+ */
+#define CONFIG_SCSI
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+#define CONFIG_SYS_64BIT_LBA
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+
+#define CONFIG_SUPPORT_VFAT
+
+/* DISK Partition support */
+#define CONFIG_EFI_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION /* Experimental */
+
+#define CONFIG_CMD_PART
+#define CONFIG_PARTITION_UUIDS
+
+#endif /* _CONFIG_MVEBU_DB_88F7040_H */
projects / karo-tx-uboot.git / commitdiff