sbc8349_config \
sbc8349_PCI_33_config \
sbc8349_PCI_66_config: unconfig
- @mkdir -p $(obj)include
- @if [ "$(findstring _PCI_,$@)" ] ; then \
- $(XECHO) -n "... PCI HOST at " ; \
- echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
- fi ; \
- if [ "$(findstring _33_,$@)" ] ; then \
- $(XECHO) -n "33MHz... " ; \
- echo "#define PCI_33M" >>$(obj)include/config.h ; \
- fi ; \
- if [ "$(findstring _66_,$@)" ] ; then \
- $(XECHO) -n "66MHz... " ; \
- echo "#define PCI_66M" >>$(obj)include/config.h ; \
- fi ;
- @$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
+ @$(MKCONFIG) -t $(@:_config=) sbc8349 ppc mpc83xx sbc8349
SIMPC8313_LP_config \
SIMPC8313_SP_config: unconfig
#endif
#include <spd_sdram.h>
#include <asm/mmu.h>
+#include <asm/io.h>
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
+#include <hwconfig.h>
+#include <fdt_support.h>
#if defined(CONFIG_PQ_MDS_PIB)
#include "../common/pq-mds-pib.h"
#endif
+#include "../../../drivers/qe/uec.h"
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* GETH1 */
{0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
};
-int board_early_init_f(void)
+/* Handle "mpc8360ea rev.2.1 erratum 2: RGMII Timing"? */
+static int board_handle_erratum2(void)
{
+ const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
+ return REVID_MAJOR(immr->sysconf.spridr) == 2 &&
+ REVID_MINOR(immr->sysconf.spridr) == 1;
+}
+
+int board_early_init_f(void)
+{
const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
/* Enable flash write */
bcsr[0xa] &= ~0x04;
/* Enable second UART */
bcsr[0x9] &= ~0x01;
+ if (board_handle_erratum2()) {
+ void *immap = (immap_t *)(CONFIG_SYS_IMMR + 0x14a8);
+
+ /*
+ * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
+ * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
+ */
+ setbits_be32(immap, 0x0c003000);
+
+ /*
+ * IMMR + 0x14AC[20:27] = 10101010
+ * (data delay for both UCC's)
+ */
+ clrsetbits_be32(immap + 4, 0xff0, 0xaa0);
+ }
return 0;
}
return 0;
}
+#ifdef CONFIG_UEC_ETH
+static uec_info_t uec_info[] = {
+#ifdef CONFIG_UEC_ETH1
+ STD_UEC_INFO(1),
+#endif
+#ifdef CONFIG_UEC_ETH2
+ STD_UEC_INFO(2),
+#endif
+};
+
+int board_eth_init(bd_t *bd)
+{
+ if (board_handle_erratum2()) {
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(uec_info); i++)
+ uec_info[i].enet_interface = ENET_1000_RGMII_RXID;
+ }
+ return uec_eth_init(bd, uec_info, ARRAY_SIZE(uec_info));
+}
+#endif /* CONFIG_UEC_ETH */
+
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
u32 msize = 0;
+ u32 lbc_sdram_size;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
/*
* Initialize SDRAM if it is on local bus.
*/
- msize += sdram_init(msize * 1024 * 1024);
+ lbc_sdram_size = sdram_init(msize * 1024 * 1024);
+ if (!msize)
+ msize = lbc_sdram_size;
/* return total bus SDRAM size(bytes) -- DDR */
return (msize * 1024 * 1024);
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
+static void ft_board_fixup_qe_usb(void *blob, bd_t *bd)
{
- const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ if (!hwconfig_subarg_cmp("qe_usb", "mode", "peripheral"))
+ return;
+
+ do_fixup_by_compat(blob, "fsl,mpc8323-qe-usb", "mode",
+ "peripheral", sizeof("peripheral"), 1);
+}
+void ft_board_setup(void *blob, bd_t *bd)
+{
ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
+ ft_board_fixup_qe_usb(blob, bd);
/*
* mpc8360ea pb mds errata 2: RGMII timing
* if on mpc8360ea rev. 2.1,
* change both ucc phy-connection-types from rgmii-id to rgmii-rxid
*/
- if ((REVID_MAJOR(immr->sysconf.spridr) == 2) &&
- (REVID_MINOR(immr->sysconf.spridr) == 1)) {
+ if (board_handle_erratum2()) {
int nodeoffset;
const char *prop;
int path;
* Byte stream. Convert the values.
*/
newp++;
- while ((*newp != ']') && (stridx < count)) {
- tmp = simple_strtoul(newp, &newp, 16);
- *data++ = tmp & 0xFF;
- *len = *len + 1;
+ while ((stridx < count) && (*newp != ']')) {
while (*newp == ' ')
newp++;
- if (*newp != '\0')
+ if (*newp == '\0') {
newp = newval[++stridx];
+ continue;
+ }
+ if (!isxdigit(*newp))
+ break;
+ tmp = simple_strtoul(newp, &newp, 16);
+ *data++ = tmp & 0xFF;
+ *len = *len + 1;
}
if (*newp != ']') {
printf("Unexpected character '%c'\n", *newp);
}
} else {
/*
- * Assume it is a string. Copy it into our data area for
- * convenience (including the terminating '\0').
+ * Assume it is one or more strings. Copy it into our
+ * data area for convenience (including the
+ * terminating '\0's).
*/
while (stridx < count) {
- *len = strlen(newp) + 1;
+ size_t length = strlen(newp) + 1;
strcpy(data, newp);
+ data += length;
+ *len += length;
newp = newval[++stridx];
}
}
#include <common.h>
#include <mpc83xx.h>
#include <ioports.h>
-#ifdef CONFIG_USB_EHCI_FSL
#include <asm/io.h>
+#ifdef CONFIG_USB_EHCI_FSL
#include <usb/ehci-fsl.h>
#endif
*/
void cpu_init_f (volatile immap_t * im)
{
- /* Pointer is writable since we allocated a register for it */
- gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
-
- /* Clear initial global data */
- memset ((void *) gd, 0, sizeof (gd_t));
-
- /* system performance tweaking */
-
-#ifdef CONFIG_SYS_ACR_PIPE_DEP
- /* Arbiter pipeline depth */
- im->arbiter.acr = (im->arbiter.acr & ~ACR_PIPE_DEP) |
- (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT);
+ __be32 acr_mask =
+#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
+ (ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_ACR_RPTCNT
- /* Arbiter repeat count */
- im->arbiter.acr = (im->arbiter.acr & ~(ACR_RPTCNT)) |
- (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT);
+#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
+ (ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
#endif
-
+ 0;
+ __be32 acr_val =
+#ifdef CONFIG_SYS_ACR_PIPE_DEP /* Arbiter pipeline depth */
+ (CONFIG_SYS_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_ACR_RPTCNT /* Arbiter repeat count */
+ (CONFIG_SYS_ACR_RPTCNT << ACR_RPTCNT_SHIFT) |
+#endif
+ 0;
+ __be32 spcr_mask =
+#ifdef CONFIG_SYS_SPCR_OPT /* Optimize transactions between CSB and other dev */
+ (SPCR_OPT << SPCR_OPT_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
+ (SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
+ (SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
+ (SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
+#endif
+ 0;
+ __be32 spcr_val =
#ifdef CONFIG_SYS_SPCR_OPT
- /* Optimize transactions between CSB and other devices */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_OPT) |
- (CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT);
+ (CONFIG_SYS_SPCR_OPT << SPCR_OPT_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSECEP
- /* all eTSEC's Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) |
- (CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSECEP /* all eTSEC's Emergency priority */
+ (CONFIG_SYS_SPCR_TSECEP << SPCR_TSECEP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSEC1EP
- /* TSEC1 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) |
- (CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSEC1EP /* TSEC1 Emergency priority */
+ (CONFIG_SYS_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SPCR_TSEC2EP
- /* TSEC2 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) |
- (CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
+#ifdef CONFIG_SYS_SPCR_TSEC2EP /* TSEC2 Emergency priority */
+ (CONFIG_SYS_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_ENCCM
- /* Encryption clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) |
- (CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT);
+ 0;
+ __be32 sccr_mask =
+#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
+ (SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_PCICM
- /* PCI & DMA clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) |
- (CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
+ (SCCR_PCICM << SCCR_PCICM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSECCM
- /* all TSEC's clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSECCM) |
- (CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
+ (SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC1CM
- /* TSEC1 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) |
- (CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
+ (SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC2CM
- /* TSEC2 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) |
- (CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
+ (SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC1ON
- /* TSEC1 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) |
- (CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
+ (SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_TSEC2ON
- /* TSEC2 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) |
- (CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
+#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
+ (SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_USBMPHCM
- /* USB MPH clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) |
- (CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
+ (SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_USBDRCM
- /* USB DR clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) |
- (CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
+ (SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
#endif
-
-#ifdef CONFIG_SYS_SCCR_SATACM
- /* SATA controller clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_SATACM) |
- (CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT);
+#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
+ (SCCR_SATACM << SCCR_SATACM_SHIFT) |
+#endif
+ 0;
+ __be32 sccr_val =
+#ifdef CONFIG_SYS_SCCR_ENCCM /* Encryption clock mode */
+ (CONFIG_SYS_SCCR_ENCCM << SCCR_ENCCM_SHIFT) |
#endif
+#ifdef CONFIG_SYS_SCCR_PCICM /* PCI & DMA clock mode */
+ (CONFIG_SYS_SCCR_PCICM << SCCR_PCICM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSECCM /* all TSEC's clock mode */
+ (CONFIG_SYS_SCCR_TSECCM << SCCR_TSECCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC1CM /* TSEC1 clock mode */
+ (CONFIG_SYS_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC2CM /* TSEC2 clock mode */
+ (CONFIG_SYS_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC1ON /* TSEC1 clock switch */
+ (CONFIG_SYS_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_TSEC2ON /* TSEC2 clock switch */
+ (CONFIG_SYS_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_USBMPHCM /* USB MPH clock mode */
+ (CONFIG_SYS_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_USBDRCM /* USB DR clock mode */
+ (CONFIG_SYS_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT) |
+#endif
+#ifdef CONFIG_SYS_SCCR_SATACM /* SATA controller clock mode */
+ (CONFIG_SYS_SCCR_SATACM << SCCR_SATACM_SHIFT) |
+#endif
+ 0;
+
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
+
+ /* Clear initial global data */
+ memset ((void *) gd, 0, sizeof (gd_t));
+
+ /* system performance tweaking */
+ clrsetbits_be32(&im->arbiter.acr, acr_mask, acr_val);
+
+ clrsetbits_be32(&im->sysconf.spcr, spcr_mask, spcr_val);
+
+ clrsetbits_be32(&im->clk.sccr, sccr_mask, sccr_val);
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
- gd->reset_status = im->reset.rsr;
- im->reset.rsr = ~(RSR_RES);
+ gd->reset_status = __raw_readl(&im->reset.rsr);
+ __raw_writel(~(RSR_RES), &im->reset.rsr);
/* AER - Arbiter Event Register - store status */
- gd->arbiter_event_attributes = im->arbiter.aeatr;
- gd->arbiter_event_address = im->arbiter.aeadr;
+ gd->arbiter_event_attributes = __raw_readl(&im->arbiter.aeatr);
+ gd->arbiter_event_address = __raw_readl(&im->arbiter.aeadr);
/*
* RMR - Reset Mode Register
* contains checkstop reset enable (4.6.1.4)
*/
- im->reset.rmr = (RMR_CSRE & (1<<RMR_CSRE_SHIFT));
-
- /* LCRR - Clock Ratio Register (10.3.1.16) */
- im->lbus.lcrr = CONFIG_SYS_LCRR;
+ __raw_writel(RMR_CSRE & (1<<RMR_CSRE_SHIFT), &im->reset.rmr);
- /* Enable Time Base & Decrimenter ( so we will have udelay() )*/
- im->sysconf.spcr |= SPCR_TBEN;
+ /* Enable Time Base & Decrementer ( so we will have udelay() )*/
+ setbits_be32(&im->sysconf.spcr, SPCR_TBEN);
/* System General Purpose Register */
#ifdef CONFIG_SYS_SICRH
#if defined(CONFIG_MPC834x) || defined(CONFIG_MPC8313)
/* regarding to MPC34x manual rev.1 bits 28..29 must be preserved */
- im->sysconf.sicrh = (im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH;
+ __raw_writel((im->sysconf.sicrh & 0x0000000C) | CONFIG_SYS_SICRH,
+ &im->sysconf.sicrh);
#else
- im->sysconf.sicrh = CONFIG_SYS_SICRH;
+ __raw_writel(CONFIG_SYS_SICRH, &im->sysconf.sicrh);
#endif
#endif
#ifdef CONFIG_SYS_SICRL
- im->sysconf.sicrl = CONFIG_SYS_SICRL;
+ __raw_writel(CONFIG_SYS_SICRL, &im->sysconf.sicrl);
#endif
- /* DDR control driver register */
-#ifdef CONFIG_SYS_DDRCDR
- im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR;
+#ifdef CONFIG_SYS_DDRCDR /* DDR control driver register */
+ __raw_writel(CONFIG_SYS_DDRCDR, &im->sysconf.ddrcdr);
#endif
- /* Output buffer impedance register */
-#ifdef CONFIG_SYS_OBIR
- im->sysconf.obir = CONFIG_SYS_OBIR;
+#ifdef CONFIG_SYS_OBIR /* Output buffer impedance register */
+ __raw_writel(CONFIG_SYS_OBIR, &im->sysconf.obir);
#endif
#ifdef CONFIG_QE
/* Wait for clock to stabilize */
do {
- temp = in_be32(&ehci->control);
+ temp = __raw_readl(&ehci->control);
udelay(1000);
} while (!(temp & PHY_CLK_VALID));
#endif
int cpu_init_r (void)
{
+ volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
#ifdef CONFIG_QE
uint qe_base = CONFIG_SYS_IMMR + 0x00100000; /* QE immr base */
+#endif
+ __be32 lcrr_mask =
+#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
+ LCRR_DBYP |
+#endif
+#ifdef CONFIG_SYS_LCRR_EADC /* external address delay */
+ LCRR_EADC |
+#endif
+#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
+ LCRR_CLKDIV |
+#endif
+ 0;
+ __be32 lcrr_val =
+#ifdef CONFIG_SYS_LCRR_DBYP /* PLL bypass */
+ CONFIG_SYS_LCRR_DBYP |
+#endif
+#ifdef CONFIG_SYS_LCRR_EADC
+ CONFIG_SYS_LCRR_EADC |
+#endif
+#ifdef CONFIG_SYS_LCRR_CLKDIV /* system clock divider */
+ CONFIG_SYS_LCRR_CLKDIV |
+#endif
+ 0;
+
+ /* LCRR - Clock Ratio Register (10.3.1.16)
+ * write, read, and isync per MPC8379ERM rev.1 CLKDEV field description
+ */
+ clrsetbits_be32(&im->lbus.lcrr, lcrr_mask, lcrr_val);
+ __raw_readl(&im->lbus.lcrr);
+ isync();
+
+#ifdef CONFIG_QE
qe_init(qe_base);
qe_reset();
#endif
#include "common.h"
#include "qe.h"
+#include "asm/immap_qe.h"
/* Fast or Giga ethernet
*/
#ifndef __UEC_H__
#define __UEC_H__
+#include "qe.h"
+#include "uccf.h"
+
#define MAX_TX_THREADS 8
#define MAX_RX_THREADS 8
#define MAX_TX_QUEUES 8
ENET_1000_RGMII,
ENET_1000_RGMII_ID,
ENET_1000_RGMII_RXID,
+ ENET_1000_RGMII_TXID,
ENET_1000_TBI,
ENET_1000_RTBI,
ENET_1000_SGMII
{
struct eth_device *edev = mii_info->dev;
uec_private_t *uec = edev->priv;
+ enum enet_interface iface = uec->uec_info->enet_interface;
- if (uec->uec_info->enet_interface == ENET_1000_RGMII_ID) {
+ if (iface == ENET_1000_RGMII_ID ||
+ iface == ENET_1000_RGMII_RXID ||
+ iface == ENET_1000_RGMII_TXID) {
int temp;
temp = phy_read(mii_info, MII_M1111_PHY_EXT_CR);
- temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY);
+ if (iface == ENET_1000_RGMII_ID) {
+ temp |= MII_M1111_RX_DELAY | MII_M1111_TX_DELAY;
+ } else if (iface == ENET_1000_RGMII_RXID) {
+ temp &= ~MII_M1111_TX_DELAY;
+ temp |= MII_M1111_RX_DELAY;
+ } else if (iface == ENET_1000_RGMII_TXID) {
+ temp &= ~MII_M1111_RX_DELAY;
+ temp |= MII_M1111_TX_DELAY;
+ }
phy_write(mii_info, MII_M1111_PHY_EXT_CR, temp);
temp = phy_read(mii_info, MII_M1111_PHY_EXT_SR);
/*
* Local Bus LCRR and LBCR regs
*/
-#define CONFIG_SYS_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
/*
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
#define CONFIG_NET_MULTI 1
#endif
+#define CONFIG_HWCONFIG 1
+
/*
* QE UEC ethernet configuration
*/
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9
#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_GMII
+#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID
#endif
#define CONFIG_UEC_ETH2 /* GETH2 */
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4
#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_GMII
+#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID
#endif
/*
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/* LB sdram refresh timer, about 6us */
/*
* Local Bus LCRR and LBCR regs
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_1 | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
/* board pre init: do not call, nothing to do */
#undef CONFIG_BOARD_EARLY_INIT_F
/*
* Local Bus Configuration & Clock Setup
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_2
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
/*
* Init Local Bus Memory Controller:
#ifndef __CONFIG_H
#define __CONFIG_H
+/*
+ * Top level Makefile configuration choices
+ */
+#ifdef CONFIG_MK_PCI
+#define CONFIG_PCI
+#endif
+
+#ifdef CONFIG_MK_66
+#define PCI_66M
+#endif
+
+#ifdef CONFIG_MK_33
+#define PCI_33M
+#endif
+
/*
* High Level Configuration Options
*/
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
projects / karo-tx-uboot.git / commitdiff