--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com.
+ * Based on the sequoia configuration file.
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * PMC440.h - configuration for esd PMC440 boards
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+
+#define CONFIG_SYS_CLK_FREQ 33333400
+
+#define CONFIG_4xx_DCACHE /* enable dcache */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */
+
+#define CONFIG_PRAM 0 /* use pram variable to overwrite */
+
+#define CFG_BOOT_BASE_ADDR 0xf0000000
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
+#define CFG_OCM_BASE 0xe0010000 /* ocm */
+#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
+#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
+#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
+#define CFG_PCI_MEMSIZE 0x80000000 /* 2GB! */
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
+
+#define CFG_USB2D0_BASE 0xe0000100
+#define CFG_USB_DEVICE 0xe0000000
+#define CFG_USB_HOST 0xe0000400
+#define CFG_FPGA_BASE0 0xef000000 /* 32 bit */
+#define CFG_FPGA_BASE1 0xef100000 /* 16 bit */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
+#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
+#define CFG_INIT_RAM_END (4 << 10)
+#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SERIAL_MULTI 1
+#undef CONFIG_UART1_CONSOLE /* console on front panel */
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
+#else
+#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#endif
+
+/*-----------------------------------------------------------------------
+ * RTC
+ *----------------------------------------------------------------------*/
+#define CONFIG_RTC_RX8025
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#endif
+
+#ifdef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
+#endif
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller. sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
+#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CFG_NAND_ECCSIZE 256
+#define CFG_NAND_ECCBYTES 3
+#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM (256) /* 256MB */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CONFIG_I2C_CMD_TREE 1
+#define CONFIG_I2C_MULTI_BUS 1
+
+#define CFG_I2C_MULTI_EEPROMS
+
+#define CFG_I2C_EEPROM_ADDR 0x54
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 5
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+
+#define CFG_EEPROM_WREN 1
+#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
+
+/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the TMP401
+ */
+#define CONFIG_DTT_SENSORS { 0, 1 }
+
+/*
+ * The PMC440 uses a TI TMP401 temperature sensor. This part
+ * is basically compatible to the ADM1021 that is supported
+ * by U-Boot.
+ *
+ * - i2c addr 0x4c
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
+ */
+#define CONFIG_DTT_ADM1021
+#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#undef CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME pmc440
+#define CFG_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0"
+#define CFG_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CFG_BOOTFILE \
+ CFG_ROOTPATH \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "kernel_addr=FC000000\0" \
+ "ramdisk_addr=FC180000\0" \
+ "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \
+ "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
+ "cp.b 200000 FFFA0000 60000\0" \
+ ""
+
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_IBM_EMAC4_V4 1
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
+
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI 1
+#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
+#define CONFIG_PHY1_ADDR 1
+#define CONFIG_RESET_PHY_R 1
+
+/* USB */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CFG_OHCI_BE_CONTROLLER
+
+#define CFG_USB_OHCI_BOARD_INIT 1
+#define CFG_USB_OHCI_CPU_INIT 1
+#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
+#define CFG_USB_OHCI_SLOT_NAME "ppc440"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+/* POST support */
+/* ethernet POST sometimes freezes the CPU.
+ * So disable it for now until issue is solved
+ */
+#if 0
+#define CONFIG_POST (CFG_POST_MEMORY | \
+ CFG_POST_CPU | \
+ CFG_POST_UART | \
+ CFG_POST_I2C | \
+ CFG_POST_CACHE | \
+ CFG_POST_FPU | \
+ CFG_POST_ETHER | \
+ CFG_POST_SPR)
+#else
+#define CONFIG_POST (CFG_POST_MEMORY | \
+ CFG_POST_CPU | \
+ CFG_POST_UART | \
+ CFG_POST_I2C | \
+ CFG_POST_CACHE | \
+ CFG_POST_FPU | \
+ CFG_POST_SPR)
+#endif
+
+#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+
+/* esd expects pram at end of physical memory.
+ * So no logbuffer at the moment.
+ */
+#if 0
+#define CONFIG_LOGBUFFER
+#endif
+#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */
+
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#define CONFIG_SUPPORT_VFAT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
+#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+/* PCI identification */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */
+#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */
+#define CFG_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC
+#define CFG_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ *----------------------------------------------------------------------*/
+#define CONFIG_FPGA
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_SPARTAN2
+#define CONFIG_FPGA_SPARTAN3
+
+#define CONFIG_FPGA_COUNT 2
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/*
+ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
+ */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_NAND_CS 2 /* NAND chip connected to CSx */
+
+/* Memory Bank 0 (NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x03017200
+#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 2 (NAND-FLASH) initialization */
+#define CFG_EBC_PB2AP 0x018003c0
+#define CFG_EBC_PB2CR (CFG_NAND_ADDR | 0x1c000)
+#else
+#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+/* Memory Bank 2 (NOR-FLASH) initialization */
+#define CFG_EBC_PB2AP 0x03017200
+#define CFG_EBC_PB2CR (CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x018003c0
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
+#endif
+
+/* Memory Bank 4 (FPGA / 32Bit) initialization */
+#define CFG_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB4CR (CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */
+
+/* Memory Bank 5 (FPGA / 16Bit) initialization */
+#define CFG_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB5CR (CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff