#define CFG_ENV_SIZE 0x0400 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
-#define CFG_NVRAM_VXWORKS_OFFS 0x7800 /* Offset for VxWorks eth-addr */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x7800) /* VxWorks eth-addr*/
#else /* Use FLASH for environment variables */
--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_APCG405 1 /* ...on a APC405 board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+ "bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+ "bootm ffc00000"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
+ CFG_CMD_ELF | \
+ CFG_CMD_DATE | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_EEPROM )
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_SUPPORT_VFAT
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#if 1 /* test-only */
+#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
+#else
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#endif
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MONITOR_BASE 0xFFF80000
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_BASE 0xFE000000 /* test-only...*/
+#define CFG_FLASH_INCREMENT 0x01000000 /* test-only */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
+#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define PS2_BA 0xF0000600 /* PS/2 Base Address */
+#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define FPGA_BA 0xF0100100 /* FPGA internal Base Address */
+#define FUJI_BA 0xF0100200 /* Fuji internal Base Address */
+#define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */
+#define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */
+#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
+
+#define CFG_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */
+
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 2 (CAN0, 1, RTC, Duart) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
+#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (PCMCIA Slot 1) initialization */
+#define CFG_EBC_PB4AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB4CR PCMCIA1_BA | 0xFA000 /*BAS=0x200,BS=128MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 5 (Epson VGA) initialization */
+#define CFG_EBC_PB5AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
+#define CFG_EBC_PB5CR VGA_BA | 0x5A000 /* BAS=0xF10,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 6 (PCMCIA Slot 2) initialization */
+#define CFG_EBC_PB6AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+
+/* FPGA internal regs */
+#define CFG_FPGA_CTRL 0x008
+
+/* FPGA Control Reg */
+#define CFG_FPGA_CTRL_CF_RESET 0x0001
+#define CFG_FPGA_CTRL_WDI 0x0002
+#define CFG_FPGA_CTRL_PS2_RESET 0x0020
+
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 80*1024 /* 80kByte is enough for XC2S50 */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * LCD Setup
+ */
+
+#define CFG_LCD_BIG_MEM 0xF1200000 /* Epson S1D13806 Mem Base Address */
+#define CFG_LCD_BIG_REG 0xF1000000 /* Epson S1D13806 Reg Base Address */
+
+#define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */
+
+/* Image information... */
+#define CONFIG_LCD_USED CONFIG_LCD_BIG
+#define CFG_LCD_HEADER_NAME "s1d13806_640_480_16bpp.h"
+#define CFG_LCD_LOGO_NAME "logo_640_480_24bpp.c"
+
+#define CFG_LCD_MEM CFG_LCD_BIG_MEM
+#define CFG_LCD_REG CFG_LCD_BIG_REG
+
+#define CFG_LCD_LOGO_MAX_SIZE (1024*1024)
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-
+#define CFG_ENV_ADDR 0xFFFB0000 /* Address of Environment Sector*/
#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#define CFG_ENV_SIZE 0x04000 /* Size of Environment */
+
+#define CFG_ENV_ADDR_REDUND 0xFFFA0000
+#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE
/*-----------------------------------------------------------------------
* Cache Configuration
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333300 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
-
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_MII | \
CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
+
#if 1 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
-#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x200 /* 512 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif
/*
- * (C) Copyright 2001-2003
+ * (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
-
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_DATE | \
CFG_CMD_JFFS2 | \
CFG_CMD_I2C | \
CFG_CMD_MII | \
CFG_CMD_PING | \
+ CFG_CMD_BSP | \
CFG_CMD_EEPROM )
+#if 0 /* test-only */
+#define CONFIG_NETCONSOLE
+#define CONFIG_NET_MULTI
+
+#ifdef CONFIG_NET_MULTI
+#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */
+#endif
+#endif
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
+#if 0 /* test-only */
+#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
+#endif
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
-
#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#undef CONFIG_LOADS_ECHO /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_DATE | \
CFG_CMD_JFFS2 | \
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
* I2C EEPROM (CAT24WC32) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */
#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
/* 32 byte page write mode using*/
/* last 5 bits of the address */
#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
/*-----------------------------------------------------------------------
* Cache Configuration
#define CFG_FPGA_MODE_CF_RESET 0x0001
#define CFG_FPGA_MODE_DUART_RESET 0x0002
#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
-#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+#define CFG_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */
+#define CFG_FPGA_MODE_SIM_OK_DIR 0x0200
+#define CFG_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400
+#define CFG_FPGA_MODE_1WIRE 0x1000
+#define CFG_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */
+#define CFG_FPGA_MODE_TESTRIG_FAIL 0x4000
/* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0 0x0001
-#define CFG_FPGA_STATUS_DIP1 0x0002
-#define CFG_FPGA_STATUS_DIP2 0x0004
-#define CFG_FPGA_STATUS_FLASH 0x0008
-#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_1WIRE 0x1000
+#define CFG_FPGA_STATUS_SIM_OK 0x2000
#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */
--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
+#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_DNS | \
+ CONFIG_BOOTP_DNS2 | \
+ CONFIG_BOOTP_SEND_HOSTNAME )
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
+ CFG_CMD_ELF | \
+ CFG_CMD_DATE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_BSP | \
+ CFG_CMD_EEPROM )
+
+#if 0 /* test-only */
+#define CONFIG_NETCONSOLE
+#define CONFIG_NET_MULTI
+
+#ifdef CONFIG_NET_MULTI
+#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */
+#endif
+#endif
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_SUPPORT_VFAT
+
+#undef CONFIG_AUTO_UPDATE /* autoupdate via compactflash */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+/* Only interrupt boot if special string is typed */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#undef CONFIG_AUTOBOOT_STOP_STR /* defined via environment var */
+#define CONFIG_AUTOBOOT_STOP_STR2 "esdesd" /* esd special for esd access*/
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFFC0000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+
+#if 0 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
+#define CFG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
+#define CFG_ENV_ADDR \
+ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-(CFG_ENV_SIZE+8)) /* Env */
+
+#else /* Use EEPROM for environment variables */
+
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+#endif
+
+#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (CAN0, 1) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_LED_ADDR 0xF0000380
+
+/* Memory Bank 3 (CompactFlash IDE) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (NVRAM/RTC) initialization */
+/*#define CFG_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
+#define CFG_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
+#define CFG_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 5 (optional Quart) initialization */
+#define CFG_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 6 (FPGA internal) initialization */
+#define CFG_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR 0xF0400000
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+/* FPGA internal regs */
+#define CFG_FPGA_MODE 0x00
+#define CFG_FPGA_STATUS 0x02
+#define CFG_FPGA_TS 0x04
+#define CFG_FPGA_TS_LOW 0x06
+#define CFG_FPGA_TS_CAP0 0x10
+#define CFG_FPGA_TS_CAP0_LOW 0x12
+#define CFG_FPGA_TS_CAP1 0x14
+#define CFG_FPGA_TS_CAP1_LOW 0x16
+#define CFG_FPGA_TS_CAP2 0x18
+#define CFG_FPGA_TS_CAP2_LOW 0x1a
+#define CFG_FPGA_TS_CAP3 0x1c
+#define CFG_FPGA_TS_CAP3_LOW 0x1e
+
+/* FPGA Mode Reg */
+#define CFG_FPGA_MODE_CF_RESET 0x0001
+#define CFG_FPGA_MODE_DUART_RESET 0x0002
+#define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
+#define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
+#define CFG_FPGA_MODE_TS_IRQ_CLEAR 0x1000
+#define CFG_FPGA_MODE_TS_CLEAR 0x2000
+
+/* FPGA Status Reg */
+#define CFG_FPGA_STATUS_DIP0 0x0001
+#define CFG_FPGA_STATUS_DIP1 0x0002
+#define CFG_FPGA_STATUS_DIP2 0x0004
+#define CFG_FPGA_STATUS_FLASH 0x0008
+#define CFG_FPGA_STATUS_TS_IRQ 0x1000
+
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
+
+#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#undef CFG_DRAM_TEST /* Disable-takes long time! */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
+#if 1
#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
+#else
+#define CFG_MONITOR_BASE 0x01fc0000 /* start of monitor */
+#endif
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#endif
-#define CONFIG_BOOTARGS "root=/dev/hda1 "
-#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
-#define CONFIG_BOOTDELAY -1 /* disable autoboot */
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_BAUDRATE 9600
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#if 0 /* test-only */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+/*************************************************************************
+ * (c) 2004 esd gmbh Hannover
+ *
+ *
+ * from db64360.h file
+ * by Reinhard Arlt reinhard.arlt@esd-electronics.com
+ *
+ ************************************************************************/
+
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/processor.h>
+
+/* This define must be before the core.h include */
+#define CONFIG_CPCI750 1 /* this is an CPCI750 board */
+
+#ifndef __ASSEMBLY__
+#include <../board/Marvell/include/core.h>
+#endif
+/*-----------------------------------------------------*/
+
+#include "../board/esd/cpci750/local.h"
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_750FX /* we have a 750FX (override local.h) */
+
+#define CONFIG_CPCI750 1 /* this is an CPCI750 board */
+
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 */
+
+#undef CONFIG_ECC /* enable ECC support */
+
+/* which initialization functions to call for this board */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+#define CFG_BOARD_NAME "CPCI750"
+#define CONFIG_IDENT_STRING "Marvell 64360 + IBM750FX"
+
+/*#define CFG_HUSH_PARSER*/
+#undef CFG_HUSH_PARSER
+
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/* Define which ETH port will be used for connecting the network */
+#define CFG_ETH_PORT ETH_0
+
+/*
+ * The following defines let you select what serial you want to use
+ * for your console driver.
+ *
+ * what to do:
+ * to use the DUART, undef CONFIG_MPSC. If you have hacked a serial
+ * cable onto the second DUART channel, change the CFG_DUART port from 1
+ * to 0 below.
+ *
+ * to use the MPSC, #define CONFIG_MPSC. If you have wired up another
+ * mpsc channel, change CONFIG_MPSC_PORT to the desired value.
+ */
+#define CONFIG_MPSC
+#define CONFIG_MPSC_PORT 0
+
+/* to change the default ethernet port, use this define (options: 0, 1, 2) */
+#define CONFIG_NET_MULTI
+#define MV_ETH_DEVS 1
+#define CONFIG_ETHER_PORT 0
+
+#undef CONFIG_ETHER_PORT_MII /* use RMII */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot disabled */
+
+#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+
+#undef CONFIG_BOOTARGS
+
+/* -----------------------------------------------------------------------------
+ * New bootcommands for Marvell CPCI750 c 2002 Ingo Assmus
+ */
+
+#define CONFIG_IPADDR "192.168.0.185"
+
+#define CONFIG_SERIAL "AA000001"
+#define CONFIG_SERVERIP "10.0.0.79"
+#define CONFIG_ROOTPATH "/export/nfs_cpci750/%s"
+
+#define CONFIG_TESTDRAMDATA y
+#define CONFIG_TESTDRAMADDRESS n
+#define CONFIG_TESETDRAMWALK n
+
+/* ----------------------------------------------------------------------------- */
+
+
+#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_ALTIVEC /* undef to disable */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_BOOTFILESIZE)
+
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_I2C \
+ | CFG_CMD_CACHE \
+ | CFG_CMD_EEPROM \
+ | CFG_CMD_PCI \
+ | CFG_CMD_ELF \
+ | CFG_CMD_DATE \
+ | CFG_CMD_NET \
+ | CFG_CMD_PING \
+ | CFG_CMD_IDE \
+ | CFG_CMD_FAT \
+ | CFG_CMD_EXT2 \
+ )
+
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_SPEED 80000 /* I2C speed default */
+
+#define CFG_GT_DUAL_CPU /* also for JTAG even with one cpu */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+/*#define CFG_MEMTEST_START 0x00400000*/ /* memtest works on */
+/*#define CFG_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */
+/*#define CFG_MEMTEST_END 0x07c00000*/ /* 4 ... 124 MB in DRAM */
+
+/*
+#define CFG_DRAM_TEST
+ * DRAM tests
+ * CFG_DRAM_TEST - enables the following tests.
+ *
+ * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines
+ * Environment variable 'test_dram_data' must be
+ * set to 'y'.
+ * CFG_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
+ * addressable. Environment variable
+ * 'test_dram_address' must be set to 'y'.
+ * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
+ * This test takes about 6 minutes to test 64 MB.
+ * Environment variable 'test_dram_walk' must be
+ * set to 'y'.
+ */
+#define CFG_DRAM_TEST
+#if defined(CFG_DRAM_TEST)
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+/*#define CFG_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */
+#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
+#define CFG_DRAM_TEST_DATA
+#define CFG_DRAM_TEST_ADDRESS
+#define CFG_DRAM_TEST_WALK
+#endif /* CFG_DRAM_TEST */
+
+#define CONFIG_DISPLAY_MEMMAP /* at the end of the bootprocess show the memory map */
+#undef CFG_DISPLAY_DIMM_SPD_CONTENT /* show SPD content during boot */
+
+#define CFG_LOAD_ADDR 0x00300000 /* default load address */
+
+#define CFG_HZ 1000 /* decr freq: 1ms ticks */
+#define CFG_BUS_HZ 133000000 /* 133 MHz (CPU = 5*Bus = 666MHz) */
+#define CFG_BUS_CLK CFG_BUS_HZ
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+#define CFG_TCLK 133000000
+
+/*#define CFG_750FX_HID0 0x8000c084*/
+#define CFG_750FX_HID0 0x80008484
+#define CFG_750FX_HID1 0x54800000
+#define CFG_750FX_HID2 0x00000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+ /*
+ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * To an unused memory region. The stack will remain in cache until RAM
+ * is initialized
+*/
+#undef CFG_INIT_RAM_LOCK
+/* #define CFG_INIT_RAM_ADDR 0x40000000*/ /* unused memory region */
+/* #define CFG_INIT_RAM_ADDR 0xfba00000*/ /* unused memory region */
+#define CFG_INIT_RAM_ADDR 0xf1080000 /* unused memory region */
+#define CFG_INIT_RAM_END 0x1000
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+#define RELOCATE_INTERNAL_RAM_ADDR
+#ifdef RELOCATE_INTERNAL_RAM_ADDR
+/*#define CFG_INTERNAL_RAM_ADDR 0xfba00000*/
+#define CFG_INTERNAL_RAM_ADDR 0xf1080000
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+/* Dummies for BAT 4-7 */
+#define CFG_SDRAM1_BASE 0x10000000 /* each 256 MByte */
+#define CFG_SDRAM2_BASE 0x20000000
+#define CFG_SDRAM3_BASE 0x30000000
+#define CFG_SDRAM4_BASE 0x40000000
+#define CFG_RESET_ADDRESS 0xfff00100
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE 0xfff00000
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 256 kB for malloc */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */
+#define CFG_FLASH_INCREMENT 0x01000000 /* there is only one bank */
+#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_BASE 0xfc000000 /* start of flash banks */
+
+/* areas to map different things with the GT in physical space */
+#define CFG_DRAM_BANKS 4
+
+/* What to put in the bats. */
+#define CFG_MISC_REGION_BASE 0xf0000000
+
+/* Peripheral Device section */
+
+/*******************************************************/
+/* We have on the cpci750 Board : */
+/* GT-Chipset Register Area */
+/* GT-Chipset internal SRAM 256k */
+/* SRAM on external device module */
+/* Real time clock on external device module */
+/* dobble UART on external device module */
+/* Data flash on external device module */
+/* Boot flash on external device module */
+/*******************************************************/
+#define CFG_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */
+#define CFG_CPCI750_RESET_ADDR 0x14000000 /* After power on Reset the CPCI750 is here */
+
+#undef MARVEL_STANDARD_CFG
+#ifndef MARVEL_STANDARD_CFG
+/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
+#define CFG_GT_REGS 0xf1000000 /* GT Registers will be mapped here */
+/*#define CFG_DEV_BASE 0xfc000000*/ /* GT Devices CS start here */
+#define CFG_INT_SRAM_BASE 0xf1080000 /* GT offers 256k internal fast SRAM */
+
+#define CFG_BOOT_SPACE 0xff000000 /* BOOT_CS0 flash 0 */
+#define CFG_DEV0_SPACE 0xfc000000 /* DEV_CS0 flash 1 */
+#define CFG_DEV1_SPACE 0xfd000000 /* DEV_CS1 flash 2 */
+#define CFG_DEV2_SPACE 0xfe000000 /* DEV_CS2 flash 3 */
+#define CFG_DEV3_SPACE 0xf0000000 /* DEV_CS3 nvram/can */
+
+#define CFG_BOOT_SIZE _16M /* cpci750 flash 0 */
+#define CFG_DEV0_SIZE _16M /* cpci750 flash 1 */
+#define CFG_DEV1_SIZE _16M /* cpci750 flash 2 */
+#define CFG_DEV2_SIZE _16M /* cpci750 flash 3 */
+#define CFG_DEV3_SIZE _16M /* cpci750 nvram/can */
+
+/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
+#endif
+
+/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected by device width */
+#define CFG_DEV0_PAR 0x8FDFFFFF /* 16 bit flash */
+#define CFG_DEV1_PAR 0x8FDFFFFF /* 16 bit flash */
+#define CFG_DEV2_PAR 0x8FDFFFFF /* 16 bit flash */
+#define CFG_DEV3_PAR 0x8FCFFFFF /* nvram/can */
+#define CFG_BOOT_PAR 0x8FDFFFFF /* 16 bit flash */
+
+ /* c 4 a 8 2 4 1 c */
+ /* 33 22|2222|22 22|111 1|11 11|1 1 | | */
+ /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */
+ /* 11|00|0100|10 10|100|0 00|10 0|100 0|001 1|100 */
+ /* 3| 0|.... ..| 2| 4 | 0 | 4 | 8 | 3 | 4 */
+
+
+/* MPP Control MV64360 Appendix P P. 632*/
+#define CFG_MPP_CONTROL_0 0x00002222 /* */
+#define CFG_MPP_CONTROL_1 0x11110000 /* */
+#define CFG_MPP_CONTROL_2 0x11111111 /* */
+#define CFG_MPP_CONTROL_3 0x00001111 /* */
+/* #define CFG_SERIAL_PORT_MUX 0x00000102*/ /* */
+
+
+#define CFG_GPP_LEVEL_CONTROL 0xffffffff /* 1111 1111 1111 1111 1111 1111 1111 1111*/
+
+/* setup new config_value for MV64360 DDR-RAM To_do !! */
+/*# define CFG_SDRAM_CONFIG 0xd8e18200*/ /* 0x448 */
+/*# define CFG_SDRAM_CONFIG 0xd8e14400*/ /* 0x1400 */
+ /* GB has high prio.
+ idma has low prio
+ MPSC has low prio
+ pci has low prio 1 and 2
+ cpu has high prio
+ Data DQS pins == eight (DQS[7:0] foe x8 and x16 devices
+ ECC disable
+ non registered DRAM */
+ /* 31:26 25:22 21:20 19 18 17 16 */
+ /* 100001 0000 010 0 0 0 0 */
+ /* refresh_count=0x400
+ phisical interleaving disable
+ virtual interleaving enable */
+ /* 15 14 13:0 */
+ /* 0 1 0x400 */
+# define CFG_SDRAM_CONFIG 0x58200400 /* 0x1400 copied from Dink32 bzw. VxWorks*/
+
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show devices on bus */
+
+/* PCI MEMORY MAP section */
+#define CFG_PCI0_MEM_BASE 0x80000000
+#define CFG_PCI0_MEM_SIZE _128M
+#define CFG_PCI1_MEM_BASE 0x88000000
+#define CFG_PCI1_MEM_SIZE _128M
+
+#define CFG_PCI0_0_MEM_SPACE (CFG_PCI0_MEM_BASE)
+#define CFG_PCI1_0_MEM_SPACE (CFG_PCI1_MEM_BASE)
+
+
+
+/* PCI I/O MAP section */
+#define CFG_PCI0_IO_BASE 0xfa000000
+#define CFG_PCI0_IO_SIZE _16M
+#define CFG_PCI1_IO_BASE 0xfb000000
+#define CFG_PCI1_IO_SIZE _16M
+
+#define CFG_PCI0_IO_SPACE (CFG_PCI0_IO_BASE)
+#define CFG_PCI0_IO_SPACE_PCI 0x00000000
+#define CFG_PCI1_IO_SPACE (CFG_PCI1_IO_BASE)
+#define CFG_PCI1_IO_SPACE_PCI 0x00000000
+
+#if defined (CONFIG_750CX)
+#define CFG_PCI_IDSEL 0x0
+#else
+#define CFG_PCI_IDSEL 0x30
+#endif
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET /* no reset for ide supported */
+#define CONFIG_IDE_PREINIT /* check for units */
+
+#define CFG_IDE_MAXBUS 2 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0
+#define CFG_ATA_IDE0_OFFSET 0
+#define CFG_ATA_IDE1_OFFSET 0
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+
+
+/*----------------------------------------------------------------------
+ * Initial BAT mappings
+ */
+
+/* NOTES:
+ * 1) GUARDED and WRITE_THRU not allowed in IBATS
+ * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
+ */
+
+/* SDRAM */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L (CFG_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT0U CFG_IBAT0U
+
+/* init ram */
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* PCI0, PCI1 in one BAT */
+#define CFG_IBAT2L BATL_NO_ACCESS
+#define CFG_IBAT2U CFG_DBAT2U
+#define CFG_DBAT2L (CFG_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* GT regs, bootrom, all the devices, PCI I/O */
+#define CFG_IBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
+#define CFG_IBAT3U (CFG_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
+#define CFG_DBAT3L (CFG_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U CFG_IBAT3U
+
+/*
+ * 750FX IBAT and DBAT pairs (To_do: define regins for I(D)BAT4 - I(D)BAT7)
+ * IBAT4 and DBAT4
+ * FIXME: ingo disable BATs for Linux Kernel
+ */
+#undef SETUP_HIGH_BATS_FX750 /* don't initialize BATS 4-7 */
+/*#define SETUP_HIGH_BATS_FX750*/ /* initialize BATS 4-7 */
+
+#ifdef SETUP_HIGH_BATS_FX750
+#define CFG_IBAT4L (CFG_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U (CFG_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L (CFG_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* IBAT5 and DBAT5 */
+#define CFG_IBAT5L (CFG_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT5U (CFG_SDRAM2_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L (CFG_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT5U CFG_IBAT5U
+
+/* IBAT6 and DBAT6 */
+#define CFG_IBAT6L (CFG_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT6U (CFG_SDRAM3_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L (CFG_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U CFG_IBAT6U
+
+/* IBAT7 and DBAT7 */
+#define CFG_IBAT7L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT7U (CFG_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT7L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT7U CFG_IBAT7U
+
+#else /* set em out of range for Linux !!!!!!!!!!! */
+#define CFG_IBAT4L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U (CFG_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* IBAT5 and DBAT5 */
+#define CFG_IBAT5L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT5U (CFG_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT5U CFG_IBAT4U
+
+/* IBAT6 and DBAT6 */
+#define CFG_IBAT6L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT6U (CFG_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U CFG_IBAT4U
+
+/* IBAT7 and DBAT7 */
+#define CFG_IBAT7L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT7U (CFG_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT7L (CFG_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT7U CFG_IBAT4U
+
+#endif
+/* FIXME: ingo end: disable BATs for Linux Kernel */
+
+/* I2C addresses for the two DIMM SPD chips */
+#define DIMM0_I2C_ADDR 0x51
+#define DIMM1_I2C_ADDR 0x52
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_BOOT_FLASH_WIDTH 2 /* 16 bit */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_LOCK_TOUT 500 /* Timeout for Flash Lock (in ms) */
+
+#if 0
+#define CFG_ENV_IS_IN_FLASH 0
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x10000
+#define CFG_ENV_ADDR 0xFFF78000 /* Marvell 8-Bit Bootflash last sector */
+/* #define CFG_ENV_ADDR (CFG_FLASH_BASE+CFG_MONITOR_LEN-CFG_ENV_SECT_SIZE) */
+#endif
+
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_EEPROM_PAGE_WRITE_BITS 5
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+#define CFG_I2C_EEPROM_ADDR 0x050
+#define CFG_ENV_OFFSET 0x200 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x600 /* 2048 bytes may be used for env vars*/
+
+#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-0x40)
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+
+/*#define CFG_L2*/
+#undef CFG_L2
+
+/* #ifdef CONFIG_750CX*/
+#if defined (CONFIG_750CX) || defined (CONFIG_750FX)
+#define L2_INIT 0
+#else
+#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+ L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
+#endif
+
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CFG_BOARD_ASM_INIT 1
+
+#endif /* __CONFIG_H */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333300 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_PRAM 2 /* reserve 2 kB "protected RAM" */
+
/*
* Miscellaneous configurable options
*/
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND "bootm fff00000"
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
CFG_CMD_ELF | \
+ CFG_CMD_MII | \
CFG_CMD_DATE | \
CFG_CMD_EEPROM )
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_G2000 1 /* ...on a PLU405 board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+
+#if 0 /* test-only */
+#define CONFIG_BAUDRATE 115200
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_PREBOOT
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off\0" \
+ "addmisc=setenv bootargs $(bootargs) " \
+ "console=ttyS0,$(baudrate) " \
+ "panic=1\0" \
+ "flash_nfs=run nfsargs addip addmisc;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip addmisc;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);" \
+ "run nfsargs addip addmisc;bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=/tftpboot/g2000/pImage\0" \
+ "kernel_addr=ff800000\0" \
+ "ramdisk_addr=ff900000\0" \
+ "pciconfighost=yes\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_NET_MULTI 1
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY1_ADDR 1 /* PHY address */
+
+#if 0 /* test-only */
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+#endif
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_ELF | \
+ CFG_CMD_DATE | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_BSP | \
+ CFG_CMD_EEPROM )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#if 0 /* test-only */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*----------------------------------------------------------------------------*/
+/* adding Ethernet setting: FTS OUI 00:11:0B */
+/*----------------------------------------------------------------------------*/
+#define CONFIG_ETHADDR 00:11:0B:00:00:01
+#define CONFIG_ETH1ADDR 00:11:0B:00:00:02
+#define CONFIG_IPADDR 10.48.8.178
+#define CONFIG_IP1ADDR 10.48.8.188
+#define CONFIG_NETMASK 255.255.255.128
+#define CONFIG_SERVERIP 10.48.8.138
+
+/*-----------------------------------------------------------------------
+ * RTC stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR 0x68
+
+#if 0 /* test-only */
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#if 0 /* APC405 */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_BASE 0xFE000000 /* test-only...*/
+#define CFG_FLASH_INCREMENT 0x01000000 /* test-only */
+#else /* G2000 */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_BASE 0xFF800000 /* test-only...*/
+#define CFG_FLASH_INCREMENT 0x01000000 /* test-only */
+#endif
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MONITOR_BASE 0xFFFC0000
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#if 1 /* test-only */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#else /* DEFAULT: environment in flash, using redundand flash sectors */
+
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CFG_ENV_ADDR 0xFFFA0000 /* environment starts before u-boot */
+#define CFG_ENV_SECT_SIZE 0x20000 /* 128k bytes may be used for env vars*/
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
+/* CAT24WC08/16... */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Intel Strata Flash) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFF87A000 /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 1 ( Power TAU) initialization */
+/* #define CFG_EBC_PB1AP 0x04041000 */
+/* #define CFG_EBC_PB1CR 0xF0018000 */ /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB1AP 0x00000000
+#define CFG_EBC_PB1CR 0x00000000
+
+/* Memory Bank 2 (Intel Flash) initialization */
+#define CFG_EBC_PB2AP 0x00000000
+#define CFG_EBC_PB2CR 0x00000000
+
+/* Memory Bank 3 (NAND) initialization */
+#define CFG_EBC_PB3AP 0x92015480
+#define CFG_EBC_PB3CR 0xF40B8000 /*addr 0xF40, BS=32M,BU=R/W, BW=8bit */
+
+/* Memory Bank 4 (FPGA regs) initialization */
+#define CFG_EBC_PB4AP 0x00000000
+#define CFG_EBC_PB4CR 0x00000000 /* leave it blank */
+
+#define CFG_NAND_BASE 0xF4000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ *
+ * following GPIO setting changed for G20000, 080304
+ */
+#define CFG_GPIO0_OSRH 0x40005555
+#define CFG_GPIO0_OSRL 0x40000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FF8014
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 1
+#define PLLMR0_DEFAULT PLLMR0_266_66_33_33
+#define PLLMR1_DEFAULT PLLMR1_266_66_33_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_HH405 1 /* ...on a HH405 board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
+
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT "autoupd"
+
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
+ CFG_CMD_ELF | \
+ CFG_CMD_NAND | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_EEPROM )
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_SUPPORT_VFAT
+
+#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
+#undef CONFIG_AUTO_UPDATE_SHOW /* use board show routine */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_BZIP2 /* include support for bzip2 compressed images */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#define CONFIG_UART1_CONSOLE /* define for uart1 as console */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
+
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFF80000
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MALLOC_LEN (2 * 1024*1024) /* Reserve 2 MB for malloc() */
+
+#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CFG_RAMBOOT 1
+#else
+# undef CFG_RAMBOOT
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR 0xF4080000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 0x8000 /* NVRAM size */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#if 0 /* test-only */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#else
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
+#endif
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
+#if 1 /* test-only */
+/* CAT24WC08/16... */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#else
+/* CAT24WC32/64... */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
+ /* 32 byte page write mode using*/
+ /* last 5 bits of the address */
+#endif
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define LCD_BA 0xF1000000 /* Epson LCD Base Address */
+#define CFG_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
+#define CFG_NVRAM_BASE 0xF4080000 /* NVRAM Base Address */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH & NVRAM) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (Epson LCD) initialization */
+#define CFG_EBC_PB4AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
+#define CFG_EBC_PB4CR LCD_BA | 0x7A000 /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * LCD Setup
+ */
+
+#define CFG_LCD_BIG_MEM 0xF1200000 /* Epson S1D13806 Mem Base Address */
+#define CFG_LCD_BIG_REG 0xF1000000 /* Epson S1D13806 Reg Base Address */
+#define CFG_LCD_SMALL_MEM 0xF1400000 /* Epson S1D13704 Mem Base Address */
+#define CFG_LCD_SMALL_REG 0xF140FFE0 /* Epson S1D13704 Reg Base Address */
+
+#define CFG_LCD_LOGO_MAX_SIZE (1024*1024)
+
+/*-----------------------------------------------------------------------
+ * Universal Interrupt Controller (UIC) Setup
+ */
+
+/*
+ * define UIC_EXT0 ... UIC_EXT6 if external interrupt is active high
+ */
+#define CFG_UIC0_POLARITY (0xFFFFFF80 | UIC_EXT6)
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+
+#define CFG_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
+
+/* FPGA internal regs */
+#define CFG_FPGA_CTRL 0x000
+
+/* FPGA Control Reg */
+#define CFG_FPGA_CTRL_REV0 0x0001
+#define CFG_FPGA_CTRL_REV1 0x0002
+#define CFG_FPGA_CTRL_VGA0_BL 0x0004
+#define CFG_FPGA_CTRL_VGA0_BL_MODE 0x0008
+#define CFG_FPGA_CTRL_CF_RESET 0x0040
+#define CFG_FPGA_CTRL_PS2_PWR 0x0080
+#define CFG_FPGA_CTRL_CF_PWR 0x0100 /* low active */
+#define CFG_FPGA_CTRL_CF_BUS_EN 0x0200
+#define CFG_FPGA_CTRL_LCD_CLK 0x7000 /* Mask for lcd clock */
+
+#define LCD_CLK_OFF 0x0000 /* Off */
+#define LCD_CLK_02083 0x1000 /* 2.083 MHz */
+#define LCD_CLK_03135 0x2000 /* 3.135 MHz */
+#define LCD_CLK_04165 0x3000 /* 4.165 MHz */
+#define LCD_CLK_06250 0x4000 /* 6.250 MHz */
+#define LCD_CLK_08330 0x5000 /* 8.330 MHz */
+#define LCD_CLK_12500 0x6000 /* 12.50 MHz */
+#define LCD_CLK_25000 0x7000 /* 25.00 MHz */
+
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555440
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0017
+
+#define CFG_LCD_ENDIAN (0x80000000 >> 7)
+#define CFG_TOUCH_RST (0x80000000 >> 9)
+#define CFG_LCD0_RST (0x80000000 >> 30)
+#define CFG_LCD1_RST (0x80000000 >> 31)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#endif
+
+#endif /* __CONFIG_H */
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_HUB405 1 /* ...on a ASH405 board */
+#define CONFIG_HUB405 1 /* ...on a HUB405 board */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+/* Ethernet stuff */
+#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
+#define CONFIG_ETHADDR 00:50:C2:1E:AF:FE
+#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD
+
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
*-----------------------------------------------------------------------
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_GPIO0_TSRL 0x00000000
#define CFG_GPIO0_TCR 0xF7FE0014
-#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_UART2_RS232 (0x80000000 >> 5)
+#define CFG_UART3_RS232 (0x80000000 >> 6)
+#define CFG_UART4_RS232 (0x80000000 >> 7)
+#define CFG_UART5_RS232 (0x80000000 >> 8)
/*
* Internal Definitions
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0410 /* PCI Device ID: OCRTC */
#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
-#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_PCI | \
#define CFG_EBC_PB7CR 0xF509A000 /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
-#define CFG_ETHERNET_MAC_ADDR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
/*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+
#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
+#define CONFIG_BOOTDELAY 0 /* autoboot after 0 seconds */
#undef CONFIG_BOOTARGS
-#if 1
-#define CONFIG_BOOTCOMMAND \
- "bootm fffc0000"
-#else
-#define CONFIG_BOOTCOMMAND \
- "mw.l 0 ffffffff; mw.l 4 ffffffff;" \
- "while cmp 0 4 1; do echo Waiting for Host...;done;" \
- "bootm 400000"
-#endif
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "mem_linux=14336k\0" \
+ "optargs=panic=0\0" \
+ "ramargs=setenv bootargs mem=$mem_linux root=/dev/ram rw\0" \
+ "addcon=setenv bootargs $bootargs console=ttyS0,$baudrate $optargs\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run ramargs;run addcon;loadpci"
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
#define CFG_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
#define CFG_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
+/* new INIT and DONE pins since board revision 1.2 (for PPC405GPr support) */
+#define CFG_FPGA_INIT_V12 0x00008000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE_V12 0x00010000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
+#if 0 /* test-only */
#define CFG_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
#define CFG_INIT_RAM_ADDR 0x40000000 /* use data cache */
#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#else
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#endif
/*
* Internal Definitions
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND "bootm fff00000"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#if 0 /* test-only */
+#define CONFIG_NET_MULTI 1
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY1_ADDR 1 /* PHY address */
+#else
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#endif
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_NAND | \
CFG_CMD_DATE | \
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
+#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
+#define CONFIG_AUTO_UPDATE_SHOW 1 /* use board show routine */
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define CONFIG_AUTOBOOT_STOP_STR " "
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
/*
- * (C) Copyright 2001-2003
+ * (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_BSP | \
CFG_CMD_MII | \
CFG_CMD_I2C | \
CFG_CMD_PING | \
- CFG_CMD_EEPROM )
+ CFG_CMD_UNIVERSE | \
+ CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000300 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
--- /dev/null
+/*
+ * Configuation settings for the esd TASREG board.
+ *
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _TASREG_H
+#define _TASREG_H
+
+#ifndef __ASSEMBLY__
+#include <asm/m5249.h>
+#endif
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF52x2 /* define processor family */
+#define CONFIG_M5249 /* define processor type */
+
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_BAUDRATE 19200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+
+#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \
+ CFG_CMD_BSP | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C ) & \
+ ~(CFG_CMD_NET))
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+#define CONFIG_BOOTDELAY 3
+
+#define CFG_PROMPT "=> "
+#define CFG_LONGHELP /* undef to save memory */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+
+#define CFG_LOAD_ADDR 0x200000 /* default load address */
+
+#define CFG_MEMTEST_START 0x400
+#define CFG_MEMTEST_END 0x380000
+
+#define CFG_HZ 1000
+
+/*
+ * Clock configuration: enable only one of the following options
+ */
+
+#if 0 /* this setting will run the cpu at 11MHz */
+#define CFG_PLL_BYPASS 1 /* bypass PLL for test purpose */
+#undef CFG_FAST_CLK /* MCF5249 can run at 140MHz */
+#define CFG_CLK 11289600 /* PLL bypass */
+#endif
+
+#if 0 /* this setting will run the cpu at 70MHz */
+#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */
+#undef CFG_FAST_CLK /* MCF5249 can run at 140MHz */
+#define CFG_CLK 72185018 /* The next lower speed */
+#endif
+
+#if 1 /* this setting will run the cpu at 140MHz */
+#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */
+#define CFG_FAST_CLK 1 /* MCF5249 can run at 140MHz */
+#define CFG_CLK 132025600 /* MCF5249 can run at 140MHz */
+#endif
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR 0x10000000 /* Register Base Addrs */
+#define CFG_MBAR2 0x80000000
+
+/*-----------------------------------------------------------------------
+ * I2C
+ */
+#define CONFIG_SOFT_I2C
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
+ /* 32 byte page write mode using*/
+ /* last 5 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+#if defined (CONFIG_SOFT_I2C)
+#if 0 /* push-pull */
+#define SDA 0x00800000
+#define SCL 0x00000008
+#define DIR0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_EN))
+#define DIR1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_EN))
+#define OUT0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_OUT))
+#define OUT1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_OUT))
+#define IN0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_READ))
+#define IN1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_READ))
+#define I2C_INIT {OUT1|=SDA;OUT0|=SCL;}
+#define I2C_READ ((IN1&SDA)?1:0)
+#define I2C_SDA(x) {if(x)OUT1|=SDA;else OUT1&=~SDA;}
+#define I2C_SCL(x) {if(x)OUT0|=SCL;else OUT0&=~SCL;}
+#define I2C_DELAY {udelay(5);}
+#define I2C_ACTIVE {DIR1|=SDA;}
+#define I2C_TRISTATE {DIR1&=~SDA;}
+#else /* open-collector */
+#define SDA 0x00800000
+#define SCL 0x00000008
+#define DIR0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_EN))
+#define DIR1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_EN))
+#define OUT0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_OUT))
+#define OUT1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_OUT))
+#define IN0 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO_READ))
+#define IN1 *((volatile ulong*)(CFG_MBAR2+MCFSIM_GPIO1_READ))
+#define I2C_INIT {DIR1&=~SDA;DIR0&=~SCL;OUT1&=~SDA;OUT0&=~SCL;}
+#define I2C_READ ((IN1&SDA)?1:0)
+#define I2C_SDA(x) {if(x)DIR1&=~SDA;else DIR1|=SDA;}
+#define I2C_SCL(x) {if(x)DIR0&=~SCL;else DIR0|=SCL;}
+#define I2C_DELAY {udelay(5);}
+#define I2C_ACTIVE {DIR1|=SDA;}
+#define I2C_TRISTATE {DIR1&=~SDA;}
+#endif
+#endif
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0x20000000
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0xFFC40000 /* Address of Environment Sector*/
+#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CFG_FLASH_BASE 0xffc00000
+
+#if 0 /* test-only */
+#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
+#endif
+
+#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
+
+#define CFG_MONITOR_LEN 0x20000
+#define CFG_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */
+#define CFG_BOOTPARAMS_LEN 64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+
+/* CS0 - AMD Flash, address 0xffc00000 */
+#define CFG_CSAR0 0xffc0
+#define CFG_CSCR0 0x1980 /* WS=0110, AA=1, PS=10 */
+/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
+#define CFG_CSMR0 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */
+
+/* CS1 - FPGA, address 0xe0000000 */
+#define CFG_CSAR1 0xe000
+#define CFG_CSCR1 0x0d80 /* WS=0011, AA=1, PS=10 */
+#define CFG_CSMR1 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CFG_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
+#define CFG_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/
+#define CFG_GPIO_EN 0x00000008 /* Set gpio output enable */
+#define CFG_GPIO1_EN 0x00c70000 /* Set gpio output enable */
+#define CFG_GPIO_OUT 0x00000008 /* Set outputs to default state */
+#define CFG_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
+
+#define CFG_GPIO1_LED 0x00400000 /* user led */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 512*1024 /* 512kByte is enough for XC2S200*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x00010000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x00040000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x00020000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00080000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00100000 /* FPGA done pin (ppc input) */
+
+#endif /* _TASREG_H */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_NAND | \
CFG_CMD_DATE | \
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#define CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFFC0000
+#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MALLOC_LEN (2 * 1024*1024) /* Reserve 2 MB for malloc() */
#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
# define CFG_RAMBOOT 1
#define CFG_EBC_PB4AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
#define CFG_EBC_PB4CR VGA_BA | 0x7A000 /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
+/*-----------------------------------------------------------------------
+ * LCD Setup
+ */
+
+#define CFG_LCD_BIG_MEM 0xF1200000 /* Epson S1D13806 Mem Base Address */
+#define CFG_LCD_BIG_REG 0xF1000000 /* Epson S1D13806 Reg Base Address */
+#define CFG_LCD_SMALL_MEM 0xF1400000 /* Epson S1D13704 Mem Base Address */
+#define CFG_LCD_SMALL_REG 0xF140FFE0 /* Epson S1D13704 Reg Base Address */
+
+#define CFG_LCD_LOGO_MAX_SIZE (1024*1024)
+
/*-----------------------------------------------------------------------
* FPGA stuff
*/
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
* GPIO0[24-27] - UART0 control signal inputs/outputs
* GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs -> GPIO
*/
#define CFG_GPIO0_OSRH 0x40000550
#define CFG_GPIO0_OSRL 0x00000110
#define CFG_GPIO0_ISR1H 0x00000000
-#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_ISR1L 0x15555440
#define CFG_GPIO0_TSRH 0x00000000
#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xF7FE0014
+#define CFG_GPIO0_TCR 0xF7FE0017
#define CFG_DUART_RST (0x80000000 >> 14)
+#define CFG_LCD_ENDIAN (0x80000000 >> 7)
+#define CFG_LCD0_RST (0x80000000 >> 30)
+#define CFG_LCD1_RST (0x80000000 >> 31)
/*
* Internal Definitions
--- /dev/null
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_VOM405 1 /* ...on a VOM405 board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_DNS | \
+ CONFIG_BOOTP_DNS2 | \
+ CONFIG_BOOTP_SEND_HOSTNAME )
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_BSP | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_EEPROM )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+#undef CONFIG_PRAM /* no "protected RAM" */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
+
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFFC0000
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CFG_RAMBOOT 1
+#else
+# undef CFG_RAMBOOT
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
+#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+/* GPIO Input: OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
+/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
+#define CFG_GPIO0_OSRH 0x40000500 /* 0 ... 15 */
+#define CFG_GPIO0_OSRL 0x00000110 /* 16 ... 31 */
+#define CFG_GPIO0_ISR1H 0x00000000 /* 0 ... 15 */
+#define CFG_GPIO0_ISR1L 0x14000045 /* 16 ... 31 */
+#define CFG_GPIO0_TSRH 0x00000000 /* 0 ... 15 */
+#define CFG_GPIO0_TSRL 0x00000000 /* 16 ... 31 */
+#define CFG_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_WUH405 1 /* ...on a WUH405 board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33333300 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_ELF | \
+ CFG_CMD_NAND | \
+ CFG_CMD_DATE | \
+ CFG_CMD_I2C | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING | \
+ CFG_CMD_EEPROM )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
+#define CFG_BASE_BAUD 691200
+#define CONFIG_UART1_CONSOLE /* define for uart1 as console */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFFC0000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+ /* have only 8kB, 16kB is save here */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x92015480
+/*#define CFG_EBC_PB0AP 0x08055880 /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x92015480
+#define CFG_EBC_PB1CR 0xF4018000 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CFG_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+#define CFG_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define DUART2_BA 0xF0000410 /* DUART Base Address */
+#define DUART3_BA 0xF0000418 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define CFG_NAND_BASE 0xF4000000
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
+#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_SIZE 0x1000
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH 0x40000550
+#define CFG_GPIO0_OSRL 0x00000110
+#define CFG_GPIO0_ISR1H 0x00000000
+#define CFG_GPIO0_ISR1L 0x15555445
+#define CFG_GPIO0_TSRH 0x00000000
+#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TCR 0xF7FE0014
+
+#define CFG_DUART_RST (0x80000000 >> 14)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#endif
+
+#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff