Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
# SPDX-License-Identifier: GPL-2.0+
#
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
obj-$(CONFIG_T4240QDS) += t4240qds.o
obj-$(CONFIG_T4240EMU) += t4240emu.o
-obj-y += ddr.o
obj-$(CONFIG_T4240QDS)+= eth.o
obj-$(CONFIG_PCI) += pci.o
+endif
+obj-y += ddr.o
obj-y += law.o
obj-y += tlb.o
puts("Initializing....using SPD\n");
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
dram_size = fsl_ddr_sdram();
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
- puts(" DDR: ");
+#else
+ /* DDR has been initialised by first stage boot loader */
+ dram_size = fsl_ddr_sdram_size();
+#endif
return dram_size;
}
--- /dev/null
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/spl.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include "../common/qixis.h"
+#include "t4240qds_qixis.h"
+
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, ccb_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#ifdef CONFIG_SPL_NAND_BOOT
+ u32 porsr1, pinctl;
+#endif
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ porsr1 = in_be32(&gur->porsr1);
+ pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+ out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+ /* compiler optimization barrier needed for GCC >= 3.4 */
+ __asm__ __volatile__("" : : : "memory");
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ ccb_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ puts("\nNAND boot...\n");
+#endif
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+ mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+
+ i2c_init_all();
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
-
+#ifndef CONFIG_SPL_BUILD
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 12, BOOKE_PAGESZ_16M, 1),
#endif
+#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 18, BOOKE_PAGESZ_1M, 1),
#endif
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 19, BOOKE_PAGESZ_2G, 1)
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SRIO_PCIE_BOOT T208xRDB:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SECURE_BOOT T4240QDS:PPC_T4160,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
-Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
+Active powerpc mpc85xx - freescale t4qds T4160QDS_NAND T4240QDS:PPC_T4160,RAMBOOT_PBL,SPL_FSL_PBL,NAND -
+Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD -
Active powerpc mpc85xx - freescale t4qds T4160QDS_SPIFLASH T4240QDS:PPC_T4160,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4240EMU T4240EMU:PPC_T4240 York Sun <yorksun@freescale.com>
Active powerpc mpc85xx - freescale t4qds T4240QDS T4240QDS:PPC_T4240 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SECURE_BOOT T4240QDS:PPC_T4240,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
-Active powerpc mpc85xx - freescale t4qds T4240QDS_NAND T4240QDS:PPC_T4240,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 -
-Active powerpc mpc85xx - freescale t4qds T4240QDS_SDCARD T4240QDS:PPC_T4240,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 -
+Active powerpc mpc85xx - freescale t4qds T4240QDS_NAND T4240QDS:PPC_T4240,RAMBOOT_PBL,SPL_FSL_PBL,NAND -
+Active powerpc mpc85xx - freescale t4qds T4240QDS_SDCARD T4240QDS:PPC_T4240,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale qemu-ppce500 qemu-ppce500 - Alexander Graf <agraf@suse.de>
Note: voltage adjustment needs to be done step by step. Changing voltage too
rapidly may cause current surge. The voltage stepping is done by software.
Users can set the final voltage directly.
+
+2-stage NAND/SD boot loader
+-------------------------------
+PBL initializes the internal SRAM and copy SPL(160K) in SRAM.
+SPL further initialise DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB) |
+-------------------------------------------------
+|GD, BD | 0xFFFC8000 (4KB) |
+-------------------------------------------------
+|ENV | 0xFFFC9000 (8KB) |
+-------------------------------------------------
+|HEAP | 0xFFFCB000 (50KB) |
+-------------------------------------------------
+|STACK | 0xFFFD8000 (22KB) |
+-------------------------------------------------
+|U-boot SPL | 0xFFFD8000 (160KB) |
+-------------------------------------------------
+
+NAND Flash memory Map on T4QDS
+--------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x140000 0x15FFFF u-boot env 128KB
+0x160000 0x17FFFF FMAN Ucode 128KB
+
+Micro SD Card memory Map on T4QDS
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0128 FMAN ucode 64KB
+
+Switch Settings: (ON is 1, OFF is 0)
+===============
+NAND boot SW setting:
+SW1[1:8] = 10000010
+SW2[1.1] = 0
+SW6[1:4] = 1001
+
+SD boot SW setting:
+SW1[1:8] = 00100000
+SW2[1.1] = 0
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t4qds/t4_pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t4qds/t4_rcw.cfg
+#if !defined(CONFIG_NAND) && !defined(CONFIG_SDCARD)
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#else
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
+#define CONFIG_SPL_PAD_TO 0x40000
+#define CONFIG_SPL_MAX_SIZE 0x28000
+#define RESET_VECTOR_OFFSET 0x27FFC
+#define BOOT_PAGE_OFFSET 0x27000
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_MMC_U_BOOT_START 0x00200000
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
#endif
+#endif /* CONFIG_RAMBOOT_PBL */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 1658)
+#define CONFIG_ENV_OFFSET (512 * 0x800)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR 0xffe20000
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
-#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#elif defined(CONFIG_SDCARD)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
/*
* Config the L3 Cache as L3 SRAM
*/
-#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_L3_SIZE (512 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_MISC_INIT_R
projects / karo-tx-uboot.git / commitdiff