libs-y += drivers/spi/
libs-$(CONFIG_FMAN_ENET) += drivers/net/fm/
libs-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
+libs-$(CONFIG_SYS_FSL_MMDC) += drivers/ddr/fsl/
libs-$(CONFIG_ALTERA_SDRAM) += drivers/ddr/altera/
libs-y += drivers/serial/
libs-y += drivers/usb/dwc3/
#define CONFIG_SYS_FSL_DDRC_ARM_GEN3 /* Enable Freescale ARM DDR3 driver */
#endif
-#ifndef CONFIG_LS1012A
+#ifdef CONFIG_LS1012A
+#define CONFIG_SYS_FSL_MMDC /* Freescale MMDC driver */
+#else
#define CONFIG_SYS_FSL_DDR /* Freescale DDR driver */
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#endif
DECLARE_GLOBAL_DATA_PTR;
-static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
-{
- int timeout = 1000;
-
- out_be32(ptr, value);
-
- while (in_be32(ptr) & bits) {
- udelay(100);
- timeout--;
- }
- if (timeout <= 0)
- puts("Error: wait for clear timeout.\n");
-}
-
int checkboard(void)
{
puts("Board: LS1012AFRDM ");
return 0;
}
-void mmdc_init(void)
-{
- struct mmdc_p_regs *mmdc =
- (struct mmdc_p_regs *)CONFIG_SYS_FSL_DDR_ADDR;
-
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- /* configure timing parms */
- out_be32(&mmdc->mdotc, CONFIG_SYS_MMDC_CORE_ODT_TIMING);
- out_be32(&mmdc->mdcfg0, CONFIG_SYS_MMDC_CORE_TIMING_CFG_0);
- out_be32(&mmdc->mdcfg1, CONFIG_SYS_MMDC_CORE_TIMING_CFG_1);
- out_be32(&mmdc->mdcfg2, CONFIG_SYS_MMDC_CORE_TIMING_CFG_2);
-
- /* other parms */
- out_be32(&mmdc->mdmisc, CONFIG_SYS_MMDC_CORE_MISC);
- out_be32(&mmdc->mpmur0, CONFIG_SYS_MMDC_PHY_MEASURE_UNIT);
- out_be32(&mmdc->mdrwd, CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY);
- out_be32(&mmdc->mpodtctrl, CONFIG_SYS_MMDC_PHY_ODT_CTRL);
-
- /* out of reset delays */
- out_be32(&mmdc->mdor, CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY);
-
- /* physical parms */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_1);
- out_be32(&mmdc->mdasp, CONFIG_SYS_MMDC_CORE_ADDR_PARTITION);
-
- /* Enable MMDC */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_2);
-
- /* dram init sequence: update MRs */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x8) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x19) |
- CMD_ADDR_LSB_MR_ADDR(0x30) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0));
-
- /* dram init sequence: ZQCL */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0));
- set_wait_for_bits_clear(&mmdc->mpzqhwctrl,
- CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL,
- FORCE_ZQ_AUTO_CALIBRATION);
-
- /* Calibrations now: wr lvl */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x84) |
- CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | WL_EN | CMD_NORMAL));
- set_wait_for_bits_clear(&mmdc->mpwlgcr, WR_LVL_HW_EN, WR_LVL_HW_EN);
-
- mdelay(1);
-
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- mdelay(1);
-
- /* Calibrations now: Read DQS gating calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- out_be32(&mmdc->mprddlctl, CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG);
- set_wait_for_bits_clear(&mmdc->mpdgctrl0,
- AUTO_RD_DQS_GATING_CALIBRATION_EN,
- AUTO_RD_DQS_GATING_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* Calibrations now: Read calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- set_wait_for_bits_clear(&mmdc->mprddlhwctl,
- AUTO_RD_CALIBRATION_EN,
- AUTO_RD_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* PD, SR */
- out_be32(&mmdc->mdpdc, CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL);
- out_be32(&mmdc->mapsr, CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT);
-
- /* refresh scheme */
- set_wait_for_bits_clear(&mmdc->mdref,
- CONFIG_SYS_MMDC_CORE_REFRESH_CTL,
- START_REFRESH);
-
- /* disable CON_REQ */
- out_be32(&mmdc->mdscr, DISABLE_CFG_REQ);
-}
-
int dram_init(void)
{
mmdc_init();
DECLARE_GLOBAL_DATA_PTR;
-static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
-{
- int timeout = 1000;
-
- out_be32(ptr, value);
-
- while (in_be32(ptr) & bits) {
- udelay(100);
- timeout--;
- }
- if (timeout <= 0)
- puts("Error: wait for clear timeout.\n");
-}
-
int checkboard(void)
{
char buf[64];
return 0;
}
-void mmdc_init(void)
-{
- struct mmdc_p_regs *mmdc =
- (struct mmdc_p_regs *)CONFIG_SYS_FSL_DDR_ADDR;
-
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- /* configure timing parms */
- out_be32(&mmdc->mdotc, CONFIG_SYS_MMDC_CORE_ODT_TIMING);
- out_be32(&mmdc->mdcfg0, CONFIG_SYS_MMDC_CORE_TIMING_CFG_0);
- out_be32(&mmdc->mdcfg1, CONFIG_SYS_MMDC_CORE_TIMING_CFG_1);
- out_be32(&mmdc->mdcfg2, CONFIG_SYS_MMDC_CORE_TIMING_CFG_2);
-
- /* other parms */
- out_be32(&mmdc->mdmisc, CONFIG_SYS_MMDC_CORE_MISC);
- out_be32(&mmdc->mpmur0, CONFIG_SYS_MMDC_PHY_MEASURE_UNIT);
- out_be32(&mmdc->mdrwd, CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY);
- out_be32(&mmdc->mpodtctrl, CONFIG_SYS_MMDC_PHY_ODT_CTRL);
-
- /* out of reset delays */
- out_be32(&mmdc->mdor, CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY);
-
- /* physical parms */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_1);
- out_be32(&mmdc->mdasp, CONFIG_SYS_MMDC_CORE_ADDR_PARTITION);
-
- /* Enable MMDC */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_2);
-
- /* dram init sequence: update MRs */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x8) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x19) |
- CMD_ADDR_LSB_MR_ADDR(0x30) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0));
-
- /* dram init sequence: ZQCL */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0));
- set_wait_for_bits_clear(&mmdc->mpzqhwctrl,
- CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL,
- FORCE_ZQ_AUTO_CALIBRATION);
-
- /* Calibrations now: wr lvl */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x84) |
- CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | WL_EN | CMD_NORMAL));
- set_wait_for_bits_clear(&mmdc->mpwlgcr, WR_LVL_HW_EN, WR_LVL_HW_EN);
-
- mdelay(1);
-
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- mdelay(1);
-
- /* Calibrations now: Read DQS gating calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- out_be32(&mmdc->mprddlctl, CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG);
- set_wait_for_bits_clear(&mmdc->mpdgctrl0,
- AUTO_RD_DQS_GATING_CALIBRATION_EN,
- AUTO_RD_DQS_GATING_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* Calibrations now: Read calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- set_wait_for_bits_clear(&mmdc->mprddlhwctl,
- AUTO_RD_CALIBRATION_EN,
- AUTO_RD_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* PD, SR */
- out_be32(&mmdc->mdpdc, CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL);
- out_be32(&mmdc->mapsr, CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT);
-
- /* refresh scheme */
- set_wait_for_bits_clear(&mmdc->mdref,
- CONFIG_SYS_MMDC_CORE_REFRESH_CTL,
- START_REFRESH);
-
- /* disable CON_REQ */
- out_be32(&mmdc->mdscr, DISABLE_CFG_REQ);
-}
-
int dram_init(void)
{
mmdc_init();
DECLARE_GLOBAL_DATA_PTR;
-static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
-{
- int timeout = 1000;
-
- out_be32(ptr, value);
-
- while (in_be32(ptr) & bits) {
- udelay(100);
- timeout--;
- }
- if (timeout <= 0)
- puts("Error: wait for clear timeout.\n");
-}
-
int checkboard(void)
{
u8 in1;
return 0;
}
-void mmdc_init(void)
-{
- struct mmdc_p_regs *mmdc =
- (struct mmdc_p_regs *)CONFIG_SYS_FSL_DDR_ADDR;
-
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- /* configure timing parms */
- out_be32(&mmdc->mdotc, CONFIG_SYS_MMDC_CORE_ODT_TIMING);
- out_be32(&mmdc->mdcfg0, CONFIG_SYS_MMDC_CORE_TIMING_CFG_0);
- out_be32(&mmdc->mdcfg1, CONFIG_SYS_MMDC_CORE_TIMING_CFG_1);
- out_be32(&mmdc->mdcfg2, CONFIG_SYS_MMDC_CORE_TIMING_CFG_2);
-
- /* other parms */
- out_be32(&mmdc->mdmisc, CONFIG_SYS_MMDC_CORE_MISC);
- out_be32(&mmdc->mpmur0, CONFIG_SYS_MMDC_PHY_MEASURE_UNIT);
- out_be32(&mmdc->mdrwd, CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY);
- out_be32(&mmdc->mpodtctrl, CONFIG_SYS_MMDC_PHY_ODT_CTRL);
-
- /* out of reset delays */
- out_be32(&mmdc->mdor, CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY);
-
- /* physical parms */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_1);
- out_be32(&mmdc->mdasp, CONFIG_SYS_MMDC_CORE_ADDR_PARTITION);
-
- /* Enable MMDC */
- out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_2);
-
- /* dram init sequence: update MRs */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x8) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x19) |
- CMD_ADDR_LSB_MR_ADDR(0x30) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0));
-
- /* dram init sequence: ZQCL */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0));
- set_wait_for_bits_clear(&mmdc->mpzqhwctrl,
- CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL,
- FORCE_ZQ_AUTO_CALIBRATION);
-
- /* Calibrations now: wr lvl */
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x84) |
- CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | WL_EN | CMD_NORMAL));
- set_wait_for_bits_clear(&mmdc->mpwlgcr, WR_LVL_HW_EN, WR_LVL_HW_EN);
-
- mdelay(1);
-
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
- out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
-
- mdelay(1);
-
- /* Calibrations now: Read DQS gating calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- out_be32(&mmdc->mprddlctl, CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG);
- set_wait_for_bits_clear(&mmdc->mpdgctrl0,
- AUTO_RD_DQS_GATING_CALIBRATION_EN,
- AUTO_RD_DQS_GATING_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* Calibrations now: Read calibration */
- out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
- CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
- out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
- CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
- out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
- set_wait_for_bits_clear(&mmdc->mprddlhwctl,
- AUTO_RD_CALIBRATION_EN,
- AUTO_RD_CALIBRATION_EN);
-
- out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
- CMD_BANK_ADDR_3));
-
- /* PD, SR */
- out_be32(&mmdc->mdpdc, CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL);
- out_be32(&mmdc->mapsr, CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT);
-
- /* refresh scheme */
- set_wait_for_bits_clear(&mmdc->mdref,
- CONFIG_SYS_MMDC_CORE_REFRESH_CTL,
- START_REFRESH);
-
- /* disable CON_REQ */
- out_be32(&mmdc->mdscr, DISABLE_CFG_REQ);
-}
-
int dram_init(void)
{
mmdc_init();
obj-$(CONFIG_SYS_FSL_DDR_86XX) += mpc86xx_ddr.o
obj-$(CONFIG_SYS_FSL_DDRC_ARM_GEN3) += arm_ddr_gen3.o
obj-$(CONFIG_SYS_FSL_DDRC_GEN4) += fsl_ddr_gen4.o
+obj-$(CONFIG_SYS_FSL_MMDC) += fsl_mmdc.o
--- /dev/null
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Generic driver for Freescale MMDC(Multi Mode DDR Controller).
+ */
+
+#include <common.h>
+#include <fsl_mmdc.h>
+#include <asm/io.h>
+
+static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
+{
+ int timeout = 1000;
+
+ out_be32(ptr, value);
+
+ while (in_be32(ptr) & bits) {
+ udelay(100);
+ timeout--;
+ }
+ if (timeout <= 0)
+ printf("Error: %p wait for clear timeout.\n", ptr);
+}
+
+void mmdc_init(void)
+{
+ struct mmdc_regs *mmdc = (struct mmdc_regs *)CONFIG_SYS_FSL_DDR_ADDR;
+ unsigned int tmp;
+
+ /* 1. set configuration request */
+ out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ);
+
+ /* 2. configure the desired timing parameters */
+ out_be32(&mmdc->mdotc, CONFIG_MMDC_MDOTC);
+ out_be32(&mmdc->mdcfg0, CONFIG_MMDC_MDCFG0);
+ out_be32(&mmdc->mdcfg1, CONFIG_MMDC_MDCFG1);
+ out_be32(&mmdc->mdcfg2, CONFIG_MMDC_MDCFG2);
+
+ /* 3. configure DDR type and other miscellaneous parameters */
+ out_be32(&mmdc->mdmisc, CONFIG_MMDC_MDMISC);
+ out_be32(&mmdc->mpmur0, MMDC_MPMUR0_FRC_MSR);
+ out_be32(&mmdc->mdrwd, CONFIG_MMDC_MDRWD);
+ out_be32(&mmdc->mpodtctrl, CONFIG_MMDC_MPODTCTRL);
+
+ /* 4. configure the required delay while leaving reset */
+ out_be32(&mmdc->mdor, CONFIG_MMDC_MDOR);
+
+ /* 5. configure DDR physical parameters */
+ /* set row/column address width, burst length, data bus width */
+ tmp = CONFIG_MMDC_MDCTL & ~(MDCTL_SDE0 | MDCTL_SDE1);
+ out_be32(&mmdc->mdctl, tmp);
+ /* configure address space partition */
+ out_be32(&mmdc->mdasp, CONFIG_MMDC_MDASP);
+
+ /* 6. perform a ZQ calibration - not needed here, doing in #8b */
+
+ /* 7. enable MMDC with the desired chip select */
+#if (CONFIG_CHIP_SELECTS_PER_CTRL == 1)
+ out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0);
+#elif (CONFIG_CHIP_SELECTS_PER_CTRL == 2)
+ out_be32(&mmdc->mdctl, tmp | MDCTL_SDE0 | MDCTL_SDE1);
+#endif
+
+ /* 8a. dram init sequence: update MRs for ZQ, ODT, PRE, etc */
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(8) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2);
+
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(0) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+
+ out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(0x19) |
+ CMD_ADDR_LSB_MR_ADDR(0x30) |
+ MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0);
+
+ /* 8b. ZQ calibration */
+ out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(0x4) | MDSCR_ENABLE_CON_REQ |
+ CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0);
+
+ set_wait_for_bits_clear(&mmdc->mpzqhwctrl, CONFIG_MMDC_MPZQHWCTRL,
+ MPZQHWCTRL_ZQ_HW_FORCE);
+
+ /* 9a. calibrations now, wr lvl */
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(0x84) |
+ MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+
+ out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | MDSCR_WL_EN |
+ CMD_NORMAL);
+
+ set_wait_for_bits_clear(&mmdc->mpwlgcr, MPWLGCR_HW_WL_EN,
+ MPWLGCR_HW_WL_EN);
+
+ mdelay(1);
+
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1);
+ out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ);
+
+ mdelay(1);
+
+ /* 9b. read DQS gating calibration */
+ out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0);
+
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+
+ out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN);
+
+ /* set absolute read delay offset */
+#if defined(CONFIG_MMDC_MPRDDLCTL)
+ out_be32(&mmdc->mprddlctl, CONFIG_MMDC_MPRDDLCTL);
+#else
+ out_be32(&mmdc->mprddlctl, MMDC_MPRDDLCTL_DEFAULT_DELAY);
+#endif
+ set_wait_for_bits_clear(&mmdc->mpdgctrl0,
+ AUTO_RD_DQS_GATING_CALIBRATION_EN,
+ AUTO_RD_DQS_GATING_CALIBRATION_EN);
+
+ out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG |
+ CMD_BANK_ADDR_3);
+
+ /* 9c. read calibration */
+ out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0);
+ out_be32(&mmdc->mdscr, CMD_ADDR_LSB_MR_ADDR(4) | MDSCR_ENABLE_CON_REQ |
+ CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3);
+ out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN);
+ set_wait_for_bits_clear(&mmdc->mprddlhwctl,
+ MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN,
+ MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN);
+
+ out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ | CMD_LOAD_MODE_REG |
+ CMD_BANK_ADDR_3);
+
+ /* 10. configure power-down, self-refresh entry, exit parameters */
+ out_be32(&mmdc->mdpdc, CONFIG_MMDC_MDPDC);
+ out_be32(&mmdc->mapsr, MMDC_MAPSR_PWR_SAV_CTRL_STAT);
+
+ /* 11. ZQ config again? do nothing here */
+
+ /* 12. refresh scheme */
+ set_wait_for_bits_clear(&mmdc->mdref, CONFIG_MMDC_MDREF,
+ MDREF_START_REFRESH);
+
+ /* 13. disable CON_REQ */
+ out_be32(&mmdc->mdscr, MDSCR_DISABLE_CFG_REQ);
+}
#include "ls1012a_common.h"
+/* DDR */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
-
-#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x04180000
-#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x84180000
-
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_CMD_MEMINFO
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+/* DDR board-specific timing parameters */
+#define CONFIG_MMDC_MDCTL 0x04180000
+#define CONFIG_MMDC_MDPDC 0x00030035
+#define CONFIG_MMDC_MDOTC 0x12554000
+#define CONFIG_MMDC_MDCFG0 0xbabf7954
+#define CONFIG_MMDC_MDCFG1 0xdb328f64
+#define CONFIG_MMDC_MDCFG2 0x01ff00db
+#define CONFIG_MMDC_MDMISC 0x00001680
+#define CONFIG_MMDC_MDREF 0x0f3c8000
+#define CONFIG_MMDC_MDRWD 0x00002000
+#define CONFIG_MMDC_MDOR 0x00bf1023
+#define CONFIG_MMDC_MDASP 0x0000003f
+#define CONFIG_MMDC_MPODTCTRL 0x0000022a
+#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
+
+
/*
* USB
*/
#include "ls1012a_common.h"
-
+/* DDR */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_SDRAM_SIZE 0x40000000
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+/* DDR board-specific timing parameters */
+#define CONFIG_MMDC_MDCTL 0x05180000
+#define CONFIG_MMDC_MDPDC 0x00030035
+#define CONFIG_MMDC_MDOTC 0x12554000
+#define CONFIG_MMDC_MDCFG0 0xbabf7954
+#define CONFIG_MMDC_MDCFG1 0xdb328f64
+#define CONFIG_MMDC_MDCFG2 0x01ff00db
+#define CONFIG_MMDC_MDMISC 0x00001680
+#define CONFIG_MMDC_MDREF 0x0f3c8000
+#define CONFIG_MMDC_MDRWD 0x00002000
+#define CONFIG_MMDC_MDOR 0x00bf1023
+#define CONFIG_MMDC_MDASP 0x0000003f
+#define CONFIG_MMDC_MPODTCTRL 0x0000022a
+#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
-#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000
-#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000
/*
* QIXIS Definitions
#include "ls1012a_common.h"
-
+/* DDR */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_SDRAM_SIZE 0x40000000
-
-#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000
-#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000
-
#define CONFIG_CMD_MEMINFO
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+/* DDR board-specific timing parameters */
+#define CONFIG_MMDC_MDCTL 0x05180000
+#define CONFIG_MMDC_MDPDC 0x00030035
+#define CONFIG_MMDC_MDOTC 0x12554000
+#define CONFIG_MMDC_MDCFG0 0xbabf7954
+#define CONFIG_MMDC_MDCFG1 0xdb328f64
+#define CONFIG_MMDC_MDCFG2 0x01ff00db
+#define CONFIG_MMDC_MDMISC 0x00001680
+#define CONFIG_MMDC_MDREF 0x0f3c8000
+#define CONFIG_MMDC_MDRWD 0x00002000
+#define CONFIG_MMDC_MDOR 0x00bf1023
+#define CONFIG_MMDC_MDASP 0x0000003f
+#define CONFIG_MMDC_MPODTCTRL 0x0000022a
+#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
+
/*
* USB
*/
#ifndef FSL_MMDC_H
#define FSL_MMDC_H
-#define CONFIG_SYS_MMDC_CORE_ODT_TIMING 0x12554000
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_0 0xbabf7954
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_1 0xff328f64
-#define CONFIG_SYS_MMDC_CORE_TIMING_CFG_2 0x01ff00db
-
-#define CONFIG_SYS_MMDC_CORE_MISC 0x00001680
-#define CONFIG_SYS_MMDC_PHY_MEASURE_UNIT 0x00000800
-#define CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY 0x00002000
-#define CONFIG_SYS_MMDC_PHY_ODT_CTRL 0x0000022a
-
-#define CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY 0x00bf1023
-
-#define CONFIG_SYS_MMDC_CORE_ADDR_PARTITION 0x0000007f
-
-#define CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL 0xa1390003
-
-#define FORCE_ZQ_AUTO_CALIBRATION (0x1 << 16)
-
-/* PHY Write Leveling Configuration and Error Status (MPWLGCR) */
-#define WR_LVL_HW_EN 0x00000001
+/* PHY Write Leveling Configuration and Error Status Register (MPWLGCR) */
+#define MPWLGCR_HW_WL_EN (1 << 0)
/* PHY Pre-defined Compare and CA delay-line Configuration (MPPDCMPR2) */
-#define MPR_COMPARE_EN 0x00000001
+#define MPPDCMPR2_MPR_COMPARE_EN (1 << 0)
-#define CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG 0x40404040
/* MMDC PHY Read DQS gating control register 0 (MPDGCTRL0) */
-#define AUTO_RD_DQS_GATING_CALIBRATION_EN 0x10000000
+#define AUTO_RD_DQS_GATING_CALIBRATION_EN (1 << 28)
/* MMDC PHY Read Delay HW Calibration Control Register (MPRDDLHWCTL) */
-#define AUTO_RD_CALIBRATION_EN 0x00000010
-
-#define CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL 0x00030035
+#define MPRDDLHWCTL_AUTO_RD_CALIBRATION_EN (1 << 4)
-#define CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT 0x00001067
+/* MMDC Core Power Saving Control and Status Register (MMDC_MAPSR) */
+#define MMDC_MAPSR_PWR_SAV_CTRL_STAT 0x00001067
-#define CONFIG_SYS_MMDC_CORE_REFRESH_CTL 0x0f3c8000
-
-#define START_REFRESH 0x00000001
+/* MMDC Core Refresh Control Register (MMDC_MDREF) */
+#define MDREF_START_REFRESH (1 << 0)
/* MMDC Core Special Command Register (MDSCR) */
-#define CMD_ADDR_MSB_MR_OP(x) (x << 24)
-
-#define CMD_ADDR_LSB_MR_ADDR(x) (x << 16)
-
-#define DISABLE_CFG_REQ 0x0
-#define CONFIGURATION_REQ (0x1 << 15)
-#define WL_EN (0x1 << 9)
-
-#define CMD_NORMAL (0x0 << 4)
-#define CMD_PRECHARGE (0x1 << 4)
-#define CMD_AUTO_REFRESH (0x2 << 4)
-#define CMD_LOAD_MODE_REG (0x3 << 4)
-#define CMD_ZQ_CALIBRATION (0x4 << 4)
-#define CMD_PRECHARGE_BANK_OPEN (0x5 << 4)
-#define CMD_MRR (0x6 << 4)
-
+#define CMD_ADDR_MSB_MR_OP(x) (x << 24)
+#define CMD_ADDR_LSB_MR_ADDR(x) (x << 16)
+#define MDSCR_DISABLE_CFG_REQ (0 << 15)
+#define MDSCR_ENABLE_CON_REQ (1 << 15)
+#define MDSCR_CON_ACK (1 << 14)
+#define MDSCR_WL_EN (1 << 9)
+#define CMD_NORMAL (0 << 4)
+#define CMD_PRECHARGE (1 << 4)
+#define CMD_AUTO_REFRESH (2 << 4)
+#define CMD_LOAD_MODE_REG (3 << 4)
+#define CMD_ZQ_CALIBRATION (4 << 4)
+#define CMD_PRECHARGE_BANK_OPEN (5 << 4)
+#define CMD_MRR (6 << 4)
#define CMD_BANK_ADDR_0 0x0
#define CMD_BANK_ADDR_1 0x1
#define CMD_BANK_ADDR_2 0x2
#define CMD_BANK_ADDR_6 0x6
#define CMD_BANK_ADDR_7 0x7
+/* MMDC Core Control Register (MDCTL) */
+#define MDCTL_SDE0 (1 << 31)
+#define MDCTL_SDE1 (1 << 30)
+
+/* MMDC PHY ZQ HW control register (MMDC_MPZQHWCTRL) */
+#define MPZQHWCTRL_ZQ_HW_FORCE (1 << 16)
+
+/* MMDC PHY Measure Unit Register (MMDC_MPMUR0) */
+#define MMDC_MPMUR0_FRC_MSR (1 << 11)
+
+/* MMDC PHY Read delay-lines Configuration Register (MMDC_MPRDDLCTL) */
+/* default 64 for a quarter cycle delay */
+#define MMDC_MPRDDLCTL_DEFAULT_DELAY 0x40404040
+
/* MMDC Registers */
-struct mmdc_p_regs {
+struct mmdc_regs {
u32 mdctl;
u32 mdpdc;
u32 mdotc;
u32 mprddqby1dl;
u32 mprddqby2dl;
u32 mprddqby3dl;
- u32 res5[4];
+ u32 mpwrdqby0dl;
+ u32 mpwrdqby1dl;
+ u32 mpwrdqby2dl;
+ u32 mpwrdqby3dl;
u32 mpdgctrl0;
u32 mpdgctrl1;
u32 mpdgdlst0;
u32 mpdccr;
};
+void mmdc_init(void);
+
+#if !defined(CONFIG_MMDC_MDCTL)
+#error Must configure board-specific timing CONFIG_MMDC_* in <board>.h for MMDC
+#endif
+
#endif /* FSL_MMDC_H */
projects / karo-tx-uboot.git / commitdiff