These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
config TARGET_TUXX1
bool "Support tuxx1"
-config TARGET_MERGERBOX
- bool "Support MERGERBOX"
-
-config TARGET_MVBLM7
- bool "Support MVBLM7"
-
config TARGET_TQM834X
bool "Support TQM834x"
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
source "board/keymile/km83xx/Kconfig"
-source "board/matrix_vision/mergerbox/Kconfig"
-source "board/matrix_vision/mvblm7/Kconfig"
source "board/mpc8308_p1m/Kconfig"
source "board/sbc8349/Kconfig"
source "board/tqc/tqm834x/Kconfig"
+++ /dev/null
-if TARGET_MERGERBOX
-
-config SYS_BOARD
- default "mergerbox"
-
-config SYS_VENDOR
- default "matrix_vision"
-
-config SYS_CONFIG_NAME
- default "MERGERBOX"
-
-endif
+++ /dev/null
-MERGERBOX BOARD
-#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
-S: Orphan (since 2014-03)
-F: board/matrix_vision/mergerbox/
-F: include/configs/MERGERBOX.h
-F: configs/MERGERBOX_defconfig
+++ /dev/null
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += mergerbox.o pci.o fpga.o sm107.o
+++ /dev/null
-Matrix Vision MergerBox
------------------------
-
-1. Board Description
-
- The MergerBox is a 120x160mm single board computing platform
- for 3D Full-HD digital video processing.
-
- Power Supply is 10-32VDC.
-
-2 System Components
-
-2.1 CPU
- Freescale MPC8377 CPU running at 800MHz core and 333MHz csb.
- 256 MByte DDR-II memory @ 333MHz data rate.
- 64 MByte Nor Flash on local bus.
- 1 GByte Nand Flash on FCM.
- 1 Vitesse VSC8601 RGMII ethernet Phys.
- 1 USB host controller over ULPI I/F with 4-Port hub.
- 2 serial ports. Console running on ttyS0 @ 115200 8N1.
- 1 mPCIe expansion slot (PCIe x1 + USB) used for Wifi/Bt.
- 2 PCIe x1 busses on local mPCIe and cutom expansion connector.
- 2 SATA host ports.
- System configuration (HRCW) is taken from I2C EEPROM.
-
-2.2 Graphics
- SM107 emebedded video controller driving a 5" 800x480 TFT panel.
- Connected over 32-Bit/66MHz PCI utilizing 4 MByte embedded memory.
-
-2.3 FPGA
- Altera Cyclone-IV EP4C115 with several PCI DMA engines.
- Connects to 7x Gennum 3G-SDI transceivers as video interconnect
- as well as a HDMI v1.4 compliant output for 3D monitoring.
- Utilizes two more DDR-II controllers providing 256MB memory.
-
-2.4 I2C
- Bus1:
- AD7418 @ 0x50 for voltage/temp. monitoring.
- SX8650 @ 0x90 touch controller for HMI.
- EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics.
- Bus2:
- mPCIe SMBus
- SiI9022A @ 0x72/0xC0 HDMI transmitter.
- TCA6416A @ 0x40 + 0x42 16-Bit I/O expander.
- LMH1983 @ 0xCA video PLL.
- DS1338C @ 0xD0 real-time clock with embedded crystal.
- 9FG104 @ 0xDC 4x 100MHz LVDS SerDes reference clock.
-
-3 Flash layout.
-
- reset vector is 0x00000100, i.e. low boot.
-
- 00000000 u-boot binary.
- 00100000 FPGA raw bit file.
- 00300000 FIT image holding kernel, dtb and rescue squashfs.
- 03d00000 u-boot environment.
- 03e00000 splash image
-
- mtd partitions are propagated to linux kernel via device tree blob.
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * (C) Copyright 2011
- * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ACEX1K.h>
-#include <command.h>
-#include "mergerbox.h"
-#include "fpga.h"
-
-Altera_CYC2_Passive_Serial_fns altera_fns = {
- fpga_null_fn,
- fpga_config_fn,
- fpga_status_fn,
- fpga_done_fn,
- fpga_wr_fn,
- fpga_null_fn,
- fpga_null_fn,
-};
-
-Altera_desc cyclone2 = {
- Altera_CYC2,
- passive_serial,
- Altera_EP2C20_SIZE,
- (void *) &altera_fns,
- NULL,
- 0
-};
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int mergerbox_init_fpga(void)
-{
- debug("Initialize FPGA interface\n");
- fpga_init();
- fpga_add(fpga_altera, &cyclone2);
-
- return 1;
-}
-
-int fpga_null_fn(int cookie)
-{
- return 0;
-}
-
-int fpga_config_fn(int assert, int flush, int cookie)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
- u32 dvo = gpio->dat;
-
- dvo &= ~FPGA_CONFIG;
- gpio->dat = dvo;
- udelay(5);
- dvo |= FPGA_CONFIG;
- gpio->dat = dvo;
-
- return assert;
-}
-
-int fpga_done_fn(int cookie)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
- int result = 0;
-
- udelay(10);
- debug("CONF_DONE check ... ");
- if (gpio->dat & FPGA_CONF_DONE) {
- debug("high\n");
- result = 1;
- } else
- debug("low\n");
-
- return result;
-}
-
-int fpga_status_fn(int cookie)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
- int result = 0;
-
- debug("STATUS check ... ");
- if (gpio->dat & FPGA_STATUS) {
- debug("high\n");
- result = 1;
- } else
- debug("low\n");
-
- return result;
-}
-
-int fpga_clk_fn(int assert_clk, int flush, int cookie)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
- u32 dvo = gpio->dat;
-
- debug("CLOCK %s\n", assert_clk ? "high" : "low");
- if (assert_clk)
- dvo |= FPGA_CCLK;
- else
- dvo &= ~FPGA_CCLK;
-
- if (flush)
- gpio->dat = dvo;
-
- return assert_clk;
-}
-
-static inline int _write_fpga(u8 val, int dump)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&im->gpio[0];
- int i;
- u32 dvo = gpio->dat;
-
- if (dump)
- debug(" %02x -> ", val);
- for (i = 0; i < 8; i++) {
- dvo &= ~FPGA_CCLK;
- gpio->dat = dvo;
- dvo &= ~FPGA_DIN;
- if (dump)
- debug("%d ", val&1);
- if (val & 1)
- dvo |= FPGA_DIN;
- gpio->dat = dvo;
- dvo |= FPGA_CCLK;
- gpio->dat = dvo;
- val >>= 1;
- }
- if (dump)
- debug("\n");
-
- return 0;
-}
-
-int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
-{
- unsigned char *data = (unsigned char *) buf;
- int i;
-
- debug("fpga_wr: buf %p / size %d\n", buf, len);
- for (i = 0; i < len; i++)
- _write_fpga(data[i], 0);
- debug("\n");
-
- return FPGA_SUCCESS;
-}
+++ /dev/null
-/*
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-extern int mergerbox_init_fpga(void);
-
-extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
-extern int fpga_status_fn(int cookie);
-extern int fpga_config_fn(int assert, int flush, int cookie);
-extern int fpga_done_fn(int cookie);
-extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
-extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
-extern int fpga_null_fn(int cookie);
+++ /dev/null
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- *
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <hwconfig.h>
-#include <i2c.h>
-#include <spi.h>
-#include <asm/io.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-#include <fdt_support.h>
-#include <spd_sdram.h>
-#include "mergerbox.h"
-#include "fpga.h"
-#include "../common/mv_common.h"
-
-static void setup_serdes(void)
-{
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-}
-
-#if defined(CONFIG_SYS_DRAM_TEST)
-int testdram(void)
-{
- uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
- uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
- uint *p;
-
- printf("Testing DRAM from 0x%08x to 0x%08x\n",
- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END);
-
- printf("DRAM test phase 1:\n");
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf("DRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf("DRAM test phase 2:\n");
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf("DRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf("DRAM test passed.\n");
- return 0;
-}
-#endif
-
-phys_size_t initdram(int board_type)
-{
- u32 msize;
-
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (clk83xx_t *)&immr->clk;
-
- /* Enable PCI_CLK[0:1] */
- clk->occr |= 0xc0000000;
- udelay(2000);
-
-#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
-#else
- immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize_log2;
-
- msize = CONFIG_SYS_DDR_SIZE;
- msize_log2 = __ilog2(msize);
-
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
- im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
-
- im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
- udelay(50000);
-
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
- udelay(1000);
-
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- udelay(1000);
-
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- __asm__ __volatile__("sync");
- udelay(1000);
-
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
- udelay(2000);
-#endif
- setup_serdes();
-
- return msize << 20;
-}
-
-int checkboard(void)
-{
- puts("Board: Matrix Vision MergerBox\n");
-
- return 0;
-}
-
-int misc_init_r(void)
-{
- u16 dim;
- int result;
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (gpio83xx_t *)&immr->gpio[1];
- unsigned char mac[6], mac_verify[6];
- char *s = getenv("reset_env");
-
- for (dim = 10; dim < 180; dim += 5) {
- mergerbox_tft_dim(dim);
- udelay(100000);
- }
-
- if (s)
- mv_reset_environment();
-
- i2c_read(SPD_EEPROM_ADDRESS, 0x80, 2, mac, sizeof(mac));
-
- /* check if Matrix Vision prefix present and export to env */
- if (mac[0] == 0x00 && mac[1] == 0x0c && mac[2] == 0x8d) {
- printf("valid MAC found in eeprom: %pM\n", mac);
- eth_setenv_enetaddr("ethaddr", mac);
- } else {
- printf("no valid MAC found in eeprom.\n");
-
- /* no: check the env */
- if (!eth_getenv_enetaddr("ethaddr", mac)) {
- printf("no valid MAC found in env either.\n");
- /* TODO: ask for valid MAC */
- } else {
- printf("valid MAC found in env: %pM\n", mac);
- printf("updating MAC in eeprom.\n");
-
- do {
- result = test_and_clear_bit(20, &gpio->dat);
- if (result)
- printf("unprotect EEPROM failed !\n");
- udelay(20000);
- } while(result);
-
- i2c_write(SPD_EEPROM_ADDRESS, 0x80, 2, mac, 6);
- udelay(20000);
-
- do {
- result = test_and_set_bit(20, &gpio->dat);
- if (result)
- printf("protect EEPROM failed !\n");
- udelay(20000);
- } while(result);
-
- printf("verify MAC %pM ... ", mac);
- i2c_read(SPD_EEPROM_ADDRESS, 0x80, 2, mac_verify, 6);
-
- if (!strncmp((char *)mac, (char *)mac_verify, 6))
- printf("ok.\n");
- else
- /* TODO: retry or do something useful */
- printf("FAILED (got %pM) !\n", mac_verify);
- }
- }
-
- return 0;
-}
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs == 0;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
-
- iopd->dat &= ~TFT_SPI_CPLD_CS;
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
-
- iopd->dat |= TFT_SPI_CPLD_CS;
-}
-
-/* control backlight pwm (display brightness).
- * allow values 0-250 with 0 = turn off and 250 = max brightness
- */
-void mergerbox_tft_dim(u16 value)
-{
- struct spi_slave *slave;
- u16 din;
- u16 dout = 0;
-
- if (value > 0 && value < 250)
- dout = 0x4000 | value;
-
- slave = spi_setup_slave(0, 0, 1000000, SPI_MODE_0 | SPI_CS_HIGH);
- spi_claim_bus(slave);
- spi_xfer(slave, 16, &dout, &din, SPI_XFER_BEGIN | SPI_XFER_END);
- spi_release_bus(slave);
- spi_free_slave(slave);
-}
-
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
- fdt_fixup_dr_usb(blob, bd);
- ft_pci_setup(blob, bd);
-}
+++ /dev/null
-/*
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __MERGERBOX_H__
-#define __MERGERBOX_H__
-
-#define MV_GPIO
-
-/*
- * GPIO Bank 1
- */
-#define TFT_SPI_EN (0x80000000>>0)
-#define FPGA_CONFIG (0x80000000>>1)
-#define FPGA_STATUS (0x80000000>>2)
-#define FPGA_CONF_DONE (0x80000000>>3)
-#define FPGA_DIN (0x80000000>>4)
-#define FPGA_CCLK (0x80000000>>5)
-#define MAN_RST (0x80000000>>6)
-#define FPGA_SYS_RST (0x80000000>>7)
-#define WD_WDI (0x80000000>>8)
-#define TFT_RST (0x80000000>>9)
-#define HISCON_GPIO1 (0x80000000>>10)
-#define HISCON_GPIO2 (0x80000000>>11)
-#define B2B_GPIO2 (0x80000000>>12)
-#define CCU_GPIN (0x80000000>>13)
-#define CCU_GPOUT (0x80000000>>14)
-#define TFT_GPIO0 (0x80000000>>15)
-#define TFT_GPIO1 (0x80000000>>16)
-#define TFT_GPIO2 (0x80000000>>17)
-#define TFT_GPIO3 (0x80000000>>18)
-#define B2B_GPIO0 (0x80000000>>19)
-#define B2B_GPIO1 (0x80000000>>20)
-#define TFT_SPI_CPLD_CS (0x80000000>>21)
-#define TFT_SPI_CS (0x80000000>>22)
-#define CCU_PWR_EN (0x80000000>>23)
-#define B2B_GPIO3 (0x80000000>>24)
-#define CCU_PWR_STAT (0x80000000>>25)
-
-#define MV_GPIO1_DAT (FPGA_CONFIG|CCU_PWR_EN|TFT_SPI_CPLD_CS)
-#define MV_GPIO1_OUT (TFT_SPI_EN|FPGA_CONFIG|FPGA_DIN|FPGA_CCLK|CCU_PWR_EN| \
- TFT_SPI_CPLD_CS)
-#define MV_GPIO1_ODE (FPGA_CONFIG|MAN_RST)
-
-/*
- * GPIO Bank 2
- */
-#define SPI_FLASH_WP (0x80000000>>10)
-#define SYS_EEPROM_WP (0x80000000>>11)
-#define SPI_FLASH_CS (0x80000000>>22)
-
-#define MV_GPIO2_DAT (SYS_EEPROM_WP|SPI_FLASH_CS)
-#define MV_GPIO2_OUT (SPI_FLASH_WP|SYS_EEPROM_WP|SPI_FLASH_CS)
-#define MV_GPIO2_ODE 0
-
-void mergerbox_tft_dim(u16 value);
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- *
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <asm/io.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-#include "mergerbox.h"
-#include "fpga.h"
-#include "../common/mv_common.h"
-
-static struct pci_region pci_regions[] = {
- {
- .bus_start = CONFIG_SYS_PCI_MEM_BASE,
- .phys_start = CONFIG_SYS_PCI_MEM_PHYS,
- .size = CONFIG_SYS_PCI_MEM_SIZE,
- .flags = PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- .bus_start = CONFIG_SYS_PCI_MMIO_BASE,
- .phys_start = CONFIG_SYS_PCI_MMIO_PHYS,
- .size = CONFIG_SYS_PCI_MMIO_SIZE,
- .flags = PCI_REGION_MEM
- },
- {
- .bus_start = CONFIG_SYS_PCI_IO_BASE,
- .phys_start = CONFIG_SYS_PCI_IO_PHYS,
- .size = CONFIG_SYS_PCI_IO_SIZE,
- .flags = PCI_REGION_IO
- }
-};
-
-static struct pci_region pcie_regions_0[] = {
- {
- .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
- .size = CONFIG_SYS_PCIE1_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
- .size = CONFIG_SYS_PCIE1_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-static struct pci_region pcie_regions_1[] = {
- {
- .bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
- .size = CONFIG_SYS_PCIE2_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE2_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
- .size = CONFIG_SYS_PCIE2_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-void pci_init_board(void)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- volatile sysconf83xx_t *sysconf = &immr->sysconf;
- volatile clk83xx_t *clk = (clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- volatile law83xx_t *pcie_law = sysconf->pcielaw;
- struct pci_region *reg[] = { pci_regions };
- struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
-
- volatile gpio83xx_t *gpio;
- gpio = (gpio83xx_t *)&immr->gpio[0];
-
- gpio->dat = MV_GPIO1_DAT;
- gpio->odr = MV_GPIO1_ODE;
- gpio->dir = MV_GPIO1_OUT;
-
- gpio = (gpio83xx_t *)&immr->gpio[1];
-
- gpio->dat = MV_GPIO2_DAT;
- gpio->odr = MV_GPIO2_ODE;
- gpio->dir = MV_GPIO2_OUT;
-
- printf("SICRH / SICRL : 0x%08x / 0x%08x\n", immr->sysconf.sicrh,
- immr->sysconf.sicrl);
-
- /* Enable PCI_CLK[0:1] */
- clk->occr |= 0xc0000000;
- udelay(2000);
-
- mergerbox_init_fpga();
- mv_load_fpga();
-
- mergerbox_tft_dim(0);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
-
- pci_law[1].bar = CONFIG_SYS_PCI_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- udelay(2000);
-
- mpc83xx_pci_init(1, reg);
-
- /* Deassert the resets in the control register */
- out_be32(&sysconf->pecr1, 0xE0008000);
- out_be32(&sysconf->pecr2, 0xE0008000);
- udelay(2000);
-
- out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- mpc83xx_pcie_init(2, pcie_reg);
-}
+++ /dev/null
-/*
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <ns16550.h>
-#include <netdev.h>
-#include <sm501.h>
-#include <pci.h>
-#include "../common/mv_common.h"
-
-#ifdef CONFIG_VIDEO
-static const SMI_REGS init_regs_800x480[] = {
- /* set endianess to little endian */
- {0x0005c, 0x00000000},
- /* PCI drive 12mA */
- {0x00004, 0x42401001},
- /* current clock */
- {0x0003c, 0x310a1818},
- /* clocks for pm0... */
- {0x00040, 0x0002184f},
- {0x00044, 0x2a1a0a01},
- /* GPIO */
- {0x10008, 0x00000000},
- {0x1000C, 0x00000000},
- /* panel control regs */
- {0x80000, 0x0f017106},
- {0x80004, 0x0},
- {0x80008, 0x0},
- {0x8000C, 0x00000000},
- {0x80010, 0x0c800c80},
- /* width 0x320 */
- {0x80014, 0x03200000},
- /* height 0x1e0 */
- {0x80018, 0x01E00000},
- {0x8001C, 0x0},
- {0x80020, 0x01df031f},
- {0x80024, 0x041f031f},
- {0x80028, 0x00800347},
- {0x8002C, 0x020c01df},
- {0x80030, 0x000201e9},
- {0x80200, 0x00000000},
- /* ZV[0:7] */
- {0x00008, 0x00ff0000},
- /* 24-Bit TFT */
- {0x0000c, 0x3f000000},
- {0, 0}
-};
-
-/*
- * Returns SM107 register base address. First thing called in the driver.
- */
-unsigned int board_video_init(void)
-{
- pci_dev_t devbusfn;
- u32 addr;
-
- devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
- if (devbusfn != -1) {
- pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1,
- (u32 *)&addr);
- return addr & 0xfffffffe;
- }
-
- return 0;
-}
-
-/*
- * Called after initializing the SM501 and before clearing the screen.
- */
-void board_validate_screen(unsigned int base)
-{
-}
-
-/*
- * Returns SM107 framebuffer address
- */
-unsigned int board_video_get_fb(void)
-{
- pci_dev_t devbusfn;
- u32 addr;
-
- devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
- if (devbusfn != -1) {
- pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0,
- (u32 *)&addr);
- addr &= 0xfffffffe;
-#ifdef CONFIG_VIDEO_SM501_FBMEM_OFFSET
- addr += CONFIG_VIDEO_SM501_FBMEM_OFFSET;
-#endif
- return addr;
- }
-
- printf("board_video_get_fb(): FAILED\n");
-
- return 0;
-}
-
-/*
- * Return a pointer to the initialization sequence.
- */
-const SMI_REGS *board_get_regs(void)
-{
- return init_regs_800x480;
-}
-
-int board_get_width(void)
-{
- return 800;
-}
-
-int board_get_height(void)
-{
- return 480;
-}
-#endif
+++ /dev/null
-bootscript.img
+++ /dev/null
-if TARGET_MVBLM7
-
-config SYS_BOARD
- default "mvblm7"
-
-config SYS_VENDOR
- default "matrix_vision"
-
-config SYS_CONFIG_NAME
- default "MVBLM7"
-
-endif
+++ /dev/null
-MVBLM7 BOARD
-#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
-S: Orphan (since 2014-03)
-F: board/matrix_vision/mvblm7/
-F: include/configs/MVBLM7.h
-F: configs/MVBLM7_defconfig
+++ /dev/null
-#
-# Copyright (C) Freescale Semiconductor, Inc. 2006.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := mvblm7.o pci.o fpga.o
-
-extra-y := bootscript.img
-
-MKIMAGEFLAGS_bootscript.image := -T script -C none -n M7_script
-
-$(obj)/bootscript.img: $(src)/bootscript
- $(call cmd,mkimage)
+++ /dev/null
-Matrix Vision mvBlueLYNX-M7 (mvBL-M7)
--------------------------------------
-
-1. Board Description
-
- The mvBL-M7 is a 120x120mm single board computing platform
- with strong focus on stereo image processing applications.
-
- Power Supply is either VDC 12-48V or Pover over Ethernet (PoE)
- on any port (requires add-on board).
-
-2 System Components
-
-2.1 CPU
- Freescale MPC8343VRAGDB CPU running at 400MHz core and 266MHz csb.
- 512MByte DDR-II memory @ 133MHz.
- 8 MByte Nor Flash on local bus.
- 2 Vitesse VSC8601 RGMII ethernet Phys.
- 1 USB host controller over ULPI I/F.
- 2 serial ports. Console running on ttyS0 @ 115200 8N1.
- 1 SD-Card slot connected to SPI.
- System configuration (HRCW) is taken from I2C EEPROM.
-
-2.2 PCI
- A miniPCI Type-III socket is present. PCI clock fixed at 66MHz.
-
-2.3 FPGA
- Altera Cyclone-II EP2C20/35 with PCI DMA engines.
- Connects to dual Matrix Vision specific CCD/CMOS sensor interfaces.
- Utilizes another 256MB DDR-II memory and 32-128MB Nand Flash.
-
-2.3.1 I/O @ FPGA
- 2x8 Outputs : Infineon High-Side Switches to Main Supply.
- 2x8 Inputs : Programmable input threshold + trigger capabilities
- 2 dedicated flash interfaces for illuminator boards.
- Cross trigger for chaining several boards.
-
-2.4 I2C
- Bus1:
- MAX5381 DAC @ 0x60 for 1st digital input threshold.
- LM75 @ 0x90 for temperature monitoring.
- EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics.
- 1st image sensor interface (slave addresses depend on sensor)
- Bus2:
- MAX5381 DAC @ 0x60 for 2nd digital input threshold.
- 2nd image sensor interface (slave addresses depend on sensor)
-
-3 Flash layout.
-
- reset vector is 0xFFF00100, i.e. "HIGHBOOT".
-
- FF800000 environment
- FF802000 redundant environment
- FF804000 u-boot script image
- FF806000 redundant u-boot script image
- FF808000 device tree blob
- FF80A000 redundant device tree blob
- FF80C000 tbd.
- FF80E000 tbd.
- FF810000 kernel
- FFC00000 root FS
- FFF00000 u-boot
- FFF80000 FPGA raw bit file
-
- mtd partitions are propagated to linux kernel via device tree blob.
-
-4 Booting
-
- On startup the bootscript @ FF804000 is executed. This script can be
- exchanged easily. Default boot mode is "boot from flash", i.e. system
- works stand-alone.
-
- This behaviour depends on some environment variables :
-
- "netboot" : yes ->try dhcp/bootp and boot from network.
- A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for
- DHCP server configuration, e.g. to provide different images to
- different devices.
-
- During netboot the system tries to get 3 image files:
- 1. Kernel - name + data is given during BOOTP.
- 2. Initrd - name is stored in "initrd_name"
- 3. device tree blob - name is stored in "dtb_name"
- Fallback files are the flash versions.
+++ /dev/null
-echo
-echo "==== running autoscript ===="
-echo
-setenv bootdtb bootm \${kernel_boot} \${mv_initrd_addr_ram} \${mv_dtb_addr_ram}
-setenv ramkernel setenv kernel_boot \${loadaddr}
-setenv flashkernel setenv kernel_boot \${mv_kernel_addr}
-setenv cpird cp \${mv_initrd_addr} \${mv_initrd_addr_ram} \${mv_initrd_length}
-setenv bootfromflash run flashkernel cpird ramparam addcons bootdtb
-setenv getdtb tftp \${mv_dtb_addr_ram} \${dtb_name}
-setenv cpdtb cp \${mv_dtb_addr} \${mv_dtb_addr_ram} 0x2000
-setenv rundtb fdt addr \${mv_dtb_addr_ram}\;fdt boardsetup
-setenv bootfromnet tftp \${mv_initrd_addr_ram} \${initrd_name}\;run ramkernel
-if test ${console} = yes;
-then
-setenv addcons setenv bootargs \${bootargs} console=ttyS\${console_nr},\${baudrate}N8
-else
-setenv addcons setenv bootargs \${bootargs} console=tty0
-fi
-setenv set_static_ip setenv ipaddr \${static_ipaddr}
-setenv set_static_nm setenv netmask \${static_netmask}
-setenv set_static_gw setenv gatewayip \${static_gateway}
-setenv set_ip setenv ip \${ipaddr}::\${gatewayip}:\${netmask}
-setenv ramparam setenv bootargs root=/dev/ram0 ro rootfstype=squashfs
-if test ${autoscript_boot} != no;
-then
- if test ${netboot} = yes;
- then
- bootp
- if test $? = 0;
- then
- echo "=== bootp succeeded -> netboot ==="
- run set_ip
- run getdtb rundtb bootfromnet ramparam addcons bootdtb
- else
- echo "=== netboot failed ==="
- fi
- fi
- run set_static_ip set_static_nm set_static_gw set_ip
- echo "=== bootfromflash ==="
- run cpdtb rundtb bootfromflash
-else
- echo "=== boot stopped with autoscript_boot no ==="
-fi
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * (C) Copyright 2008
- * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ACEX1K.h>
-#include <command.h>
-#include "fpga.h"
-#include "mvblm7.h"
-
-#ifdef FPGA_DEBUG
-#define fpga_debug(fmt, args...) printf("%s: "fmt, __func__, ##args)
-#else
-#define fpga_debug(fmt, args...)
-#endif
-
-Altera_CYC2_Passive_Serial_fns altera_fns = {
- fpga_null_fn,
- fpga_config_fn,
- fpga_status_fn,
- fpga_done_fn,
- fpga_wr_fn,
- fpga_null_fn,
- fpga_null_fn,
-};
-
-Altera_desc cyclone2 = {
- Altera_CYC2,
- passive_serial,
- Altera_EP2C20_SIZE,
- (void *) &altera_fns,
- NULL,
- 0
-};
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int mvblm7_init_fpga(void)
-{
- fpga_debug("Initialize FPGA interface\n");
- fpga_init();
- fpga_add(fpga_altera, &cyclone2);
- fpga_config_fn(0, 1, 0);
- udelay(60);
-
- return 1;
-}
-
-int fpga_null_fn(int cookie)
-{
- return 0;
-}
-
-int fpga_config_fn(int assert, int flush, int cookie)
-{
- volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
- u32 dvo = gpio->dat;
-
- fpga_debug("SET config : %s\n", assert ? "low" : "high");
- if (assert)
- dvo |= FPGA_CONFIG;
- else
- dvo &= ~FPGA_CONFIG;
-
- if (flush)
- gpio->dat = dvo;
-
- return assert;
-}
-
-int fpga_done_fn(int cookie)
-{
- volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
- int result = 0;
-
- udelay(10);
- fpga_debug("CONF_DONE check ... ");
- if (gpio->dat & FPGA_CONF_DONE) {
- fpga_debug("high\n");
- result = 1;
- } else
- fpga_debug("low\n");
-
- return result;
-}
-
-int fpga_status_fn(int cookie)
-{
- volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
- int result = 0;
-
- fpga_debug("STATUS check ... ");
- if (gpio->dat & FPGA_STATUS) {
- fpga_debug("high\n");
- result = 1;
- } else
- fpga_debug("low\n");
-
- return result;
-}
-
-int fpga_clk_fn(int assert_clk, int flush, int cookie)
-{
- volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
- u32 dvo = gpio->dat;
-
- fpga_debug("CLOCK %s\n", assert_clk ? "high" : "low");
- if (assert_clk)
- dvo |= FPGA_CCLK;
- else
- dvo &= ~FPGA_CCLK;
-
- if (flush)
- gpio->dat = dvo;
-
- return assert_clk;
-}
-
-static inline int _write_fpga(u8 val, int dump)
-{
- volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)&im->gpio[0];
- int i;
- u32 dvo = gpio->dat;
-
- if (dump)
- fpga_debug(" %02x -> ", val);
- for (i = 0; i < 8; i++) {
- dvo &= ~FPGA_CCLK;
- gpio->dat = dvo;
- dvo &= ~FPGA_DIN;
- if (dump)
- fpga_debug("%d ", val&1);
- if (val & 1)
- dvo |= FPGA_DIN;
- gpio->dat = dvo;
- dvo |= FPGA_CCLK;
- gpio->dat = dvo;
- val >>= 1;
- }
- if (dump)
- fpga_debug("\n");
-
- return 0;
-}
-
-int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
-{
- unsigned char *data = (unsigned char *) buf;
- int i;
-
- fpga_debug("fpga_wr: buf %p / size %d\n", buf, len);
- for (i = 0; i < len; i++)
- _write_fpga(data[i], 0);
- fpga_debug("\n");
-
- return FPGA_SUCCESS;
-}
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-extern int mvblm7_init_fpga(void);
-
-extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
-extern int fpga_status_fn(int cookie);
-extern int fpga_config_fn(int assert, int flush, int cookie);
-extern int fpga_done_fn(int cookie);
-extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
-extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
-extern int fpga_null_fn(int cookie);
+++ /dev/null
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006.
- *
- * (C) Copyright 2008
- * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <asm/mpc8349_pci.h>
-#include <pci.h>
-#include <spi.h>
-#include <asm/mmu.h>
-#if defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-
-#include "../common/mv_common.h"
-#include "mvblm7.h"
-
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = 0;
- u32 ddr_size;
- u32 ddr_size_log2;
- char *s = getenv("ddr_size");
-
- msize = CONFIG_SYS_DDR_SIZE;
- if (s) {
- u32 env_ddr_size = simple_strtoul(s, NULL, 10);
- if (env_ddr_size == 512)
- msize = 512;
- }
-
- for (ddr_size = msize << 20, ddr_size_log2 = 0;
- (ddr_size > 1);
- ddr_size = ddr_size >> 1, ddr_size_log2++) {
- if (ddr_size & 1)
- return -1;
- }
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
- im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) &
- LAWAR_SIZE);
-
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
-
- asm("sync;isync");
- udelay(600);
-
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
-
- asm("sync;isync");
- udelay(500);
-
- return msize;
-}
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
- return -1;
-
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
- msize = fixed_sdram();
-
- /* return total bus RAM size(bytes) */
- return msize * 1024 * 1024;
-}
-
-int misc_init_r(void)
-{
- char *s = getenv("reset_env");
-
- if (s) {
- mv_reset_environment();
- }
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: Matrix Vision mvBlueLYNX-M7\n");
-
- return 0;
-}
-
-#ifdef CONFIG_HARD_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs == 0;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
-
- iopd->dat &= ~MVBLM7_MMC_CS;
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- volatile gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
-
- iopd->dat |= ~MVBLM7_MMC_CS;
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
-}
-
-#endif
+++ /dev/null
-#ifndef __MVBC_H__
-#define __MVBC_H__
-
-#define MV_GPIO
-
-#define FPGA_CONFIG 0x80000000
-#define FPGA_CCLK 0x40000000
-#define FPGA_DIN 0x20000000
-#define FPGA_STATUS 0x10000000
-#define FPGA_CONF_DONE 0x08000000
-
-#define WD_WDI 0x00400000
-#define WD_TS 0x00200000
-#define MAN_RST 0x00100000
-
-#define MV_GPIO_DAT (WD_TS)
-#define MV_GPIO_OUT (FPGA_CONFIG|FPGA_DIN|FPGA_CCLK|MVBLM7_MMC_CS)
-#define MV_GPIO_ODE (FPGA_CONFIG|MAN_RST)
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006.
- *
- * (C) Copyright 2008
- * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#if defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-#include <pci.h>
-#include <mpc83xx.h>
-#include <fpga.h>
-#include "mvblm7.h"
-#include "fpga.h"
-#include "../common/mv_common.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct pci_region pci_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- }
-};
-
-void pci_init_board(void)
-{
- int i;
- volatile immap_t *immr;
- volatile pcictrl83xx_t *pci_ctrl;
- volatile gpio83xx_t *gpio;
- volatile clk83xx_t *clk;
- volatile law83xx_t *pci_law;
- struct pci_region *reg[] = { pci_regions };
-
- immr = (immap_t *) CONFIG_SYS_IMMR;
- clk = (clk83xx_t *) &immr->clk;
- pci_ctrl = immr->pci_ctrl;
- pci_law = immr->sysconf.pcilaw;
- gpio = (volatile gpio83xx_t *)&immr->gpio[0];
-
- gpio->dat = MV_GPIO_DAT;
- gpio->odr = MV_GPIO_ODE;
- gpio->dir = MV_GPIO_OUT;
-
- printf("SICRH / SICRL : 0x%08x / 0x%08x\n", immr->sysconf.sicrh,
- immr->sysconf.sicrl);
-
- mvblm7_init_fpga();
- mv_load_fpga();
-
- gpio->dir = MV_GPIO_OUT & ~(FPGA_DIN|FPGA_CCLK);
-
- /* Enable PCI_CLK_OUTPUTs 0 and 1 with 1:1 clocking */
- clk->occr = 0xc0000000;
-
- pci_ctrl[0].gcr = 0;
- udelay(2000);
- pci_ctrl[0].gcr = 1;
-
- for (i = 0; i < 1000; ++i)
- udelay(1000);
-
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_1GB;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- mpc83xx_pci_init(1, reg);
-}
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MERGERBOX=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MVBLM7=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+MERGERBOX powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
+MVBLM7 powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
bluestone powerpc ppc4xx - - Tirumala Marri <tmarri@apm.com>
CRAYL1 powerpc ppc4xx - - David Updegraff <dave@cray.com>
KAREF powerpc ppc4xx - - Travis Sawyer <travis.sawyer@sandburst.com>
+++ /dev/null
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- *
- * Copyright (C) 2011 Matrix Vision GmbH
- * Andre Schwarz <andre.schwarz@matrix-vision.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <version.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1
-#define CONFIG_MPC837x 1
-#define CONFIG_MPC8377 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-
-#define CONFIG_PCI 1
-#define CONFIG_PCI_INDIRECT_BRIDGE 1
-
-#define CONFIG_MASK_AER_AO
-#define CONFIG_DISPLAY_AER_FULL
-
-#define CONFIG_MISC_INIT_R
-
-/*
- * On-board devices
- */
-#define CONFIG_TSEC_ENET
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
-#define CONFIG_PCIE
-#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word stored in EEPROM.
- */
-#define CONFIG_SYS_HRCW_LOW 0
-#define CONFIG_SYS_HRCW_HIGH 0
-
-/* Arbiter Configuration Register */
-#define CONFIG_SYS_ACR_PIPE_DEP 3
-#define CONFIG_SYS_ACR_RPTCNT 3
-
-/* System Priority Control Regsiter */
-#define CONFIG_SYS_SPCR_TSECEP 3
-
-/* System Clock Configuration Register */
-#define CONFIG_SYS_SCCR_TSEC1CM 3
-#define CONFIG_SYS_SCCR_TSEC2CM 0
-#define CONFIG_SYS_SCCR_SDHCCM 3
-#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */
-#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */
-#define CONFIG_SYS_SCCR_PCIEXP1CM 3
-#define CONFIG_SYS_SCCR_PCIEXP2CM 3
-#define CONFIG_SYS_SCCR_PCICM 1
-#define CONFIG_SYS_SCCR_SATACM 0xFF
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x087c0000
-#define CONFIG_SYS_SICRL 0x40000000
-
-/*
- * Output Buffer Impedance
- */
-#define CONFIG_SYS_OBIR 0x30000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN | DDRCDR_PZ_HIZ |\
- DDRCDR_NZ_HIZ | DDRCDR_ODT |\
- DDRCDR_Q_DRN)
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-
-#define CONFIG_SYS_DDR_MODE_WEAK
-#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2
-#define CONFIG_SYS_DDR_CPO 0x1f
-
-/* SPD table located at offset 0x20 in extended adressing ROM
- * used for HRCW fetch after power-on reset
- */
-#define CONFIG_SPD_EEPROM
-#define SPD_EEPROM_ADDRESS 0x50
-#define SPD_EEPROM_OFFSET 0x20
-#define SPD_EEPROM_ADDR_LEN 2
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (512*1024)
-#define CONFIG_SYS_MALLOC_LEN (512*1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
- GENERATED_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-#define CONFIG_FSL_ELBC 1
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_FLASH_SIZE 64
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 |\
- BR_MS_GPCM | BR_V)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\
- OR_GPCM_XACS | OR_GPCM_SCY_15 |\
- OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\
- OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-/*
- * NAND Flash on the Local Bus
- */
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_FSL_ELBC 1
-
-#define CONFIG_SYS_NAND_BASE 0xE0600000
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\
- BR_PS_8 | BR_MS_FCM | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\
- OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\
- OR_FCM_TRLX | OR_FCM_EHTR)
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-#define CONFIG_CONSOLE ttyS0
-#define CONFIG_BAUDRATE 115200
-
-/* SERDES */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1 0xe3000
-#define CONFIG_FSL_SERDES2 0xe3100
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20)
-#define CONFIG_SYS_PCI_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE (1 << 20)
-
-#ifdef CONFIG_PCIE
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20)
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20)
-
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20)
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20)
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
-#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20)
-#endif
-
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-/*
- * TSEC
- */
-#define CONFIG_GMII /* MII PHY management */
-#define CONFIG_SYS_VSC8601_SKEWFIX
-#define CONFIG_SYS_VSC8601_SKEW_TX 3
-#define CONFIG_SYS_VSC8601_SKEW_RX 3
-
-#define CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define TSEC1_PHY_ADDR 0x10
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHYIDX 0
-
-#define CONFIG_ETHPRIME "TSEC0"
-#define CONFIG_HAS_ETH0
-
-/*
- * SATA
- */
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET 0x18000
-#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET 0x19000
-#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_VENDOREX
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_RANDOM_DELAY
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_LIB_RAND
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_SATA
-
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-
-#define CONFIG_RBTREE
-#define CONFIG_LZO
-
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
-#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"
-
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE 1
-
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_LOAD_ADDR 0x2000000
-#define CONFIG_LOADADDR 0x4000000
-#define CONFIG_SYS_CBSIZE 256
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_LOADS_ECHO 1
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-
-#define CONFIG_SYS_MEMTEST_START (60<<20)
-#define CONFIG_SYS_MEMTEST_END (70<<20)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-#define CONFIG_HIGH_BATS 1
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE
-
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* unused */
-#define CONFIG_SYS_IBAT1L (0)
-#define CONFIG_SYS_IBAT1U (0)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_RW |\
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* unused */
-#define CONFIG_SYS_IBAT3L (0)
-#define CONFIG_SYS_IBAT3U (0)
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-/*
- * I2C EEPROM settings
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_SIZE 0x4000
-
-/*
- * Environment Configuration
- */
-#define CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0xFFD00000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-
-/*
- * Video
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_SM501_PCI
-#define VIDEO_FB_LITTLE_ENDIAN
-#define CONFIG_CMD_BMP
-#define CONFIG_VIDEO_SM501
-#define CONFIG_VIDEO_SM501_32BPP
-#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
-
-/*
- * SPI
- */
-#define CONFIG_MPC8XXX_SPI
-
-/*
- * USB
- */
-#define CONFIG_SYS_USB_HOST
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_KEYBOARD
-/*
- *
- */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_RESET_TO_RETRY 1000
-
-#define MV_CI "MergerBox"
-#define MV_VCI "MergerBox"
-#define MV_FPGA_DATA 0xfc100000
-#define MV_FPGA_SIZE 0x00200000
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1
-
-#define MV_KERNEL_ADDR_RAM 0x02800000
-#define MV_DTB_ADDR_RAM 0x00600000
-#define MV_INITRD_ADDR_RAM 0x01000000
-#define MV_FITADDR 0xfc300000
-#define MV_SPLAH_ADDR 0xffe00000
-
-#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\
- "then; run fitboot;else;run ubiboot;fi;"
-#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console_nr=0\0"\
- "stdin=serial\0"\
- "stdout=serial\0"\
- "stderr=serial\0"\
- "boot_sqfs=1\0"\
- "usb_dr_mode=host\0"\
- "bootfile=MergerBox.fit\0"\
- "baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
- "fpga=0\0"\
- "fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
- "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
- "mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
- "mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
- "mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
- "uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
- "fitaddr=" __stringify(MV_FITADDR) "\0"\
- "mv_version=" U_BOOT_VERSION "\0"\
- "mtdids=" MTDIDS_DEFAULT "\0"\
- "mtdparts=" MTDPARTS_DEFAULT "\0"\
- "dhcp_client_id=" MV_CI "\0"\
- "dhcp_vendor-class-identifier=" MV_VCI "\0"\
- "upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
- "protect off all;erase $uboota +0xC0000;"\
- "cp.b $loadaddr $uboota $filesize\0"\
- "upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
- "cp.b $loadaddr $fpgadata $filesize\0"\
- "upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
- "cp.b $loadaddr $fitaddr $filesize\0"\
- "addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
- "rootfstype=squashfs\0"\
- "addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
- "rootfstype=ubifs\0"\
- "addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
- "rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
- "netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
- "netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
- "ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
- "doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
- "fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
- "imxtract $fitaddr ramdisk $mv_initrd_ram;"\
- "imxtract $fitaddr fdt $mv_dtb_ram\0"\
- "fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
- "fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
- "i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
- "i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
- "i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
- "i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
- "i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
- "init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
- "i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
- "splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
- ""
-
-/*
- * FPGA
- */
-#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) Matrix Vision GmbH 2008
- *
- * Matrix Vision mvBlueLYNX-M7 configuration file
- * based on Freescale's MPC8349ITX.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <version.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1
-#define CONFIG_MPC834x 1
-#define CONFIG_MPC8343 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_SYS_IMMR 0xE0000000
-
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_SKIP_HOST_BRIDGE
-#define CONFIG_TSEC_ENET
-#define CONFIG_MPC8XXX_SPI
-#define CONFIG_HARD_SPI
-#define MVBLM7_MMC_CS 0x04000000
-#define CONFIG_MISC_INIT_R
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 100000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 100000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/*
- * DDR Setup
- */
-#undef CONFIG_SPD_EEPROM
-
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_83XX_DDR_USES_CS0 1
-#define CONFIG_SYS_MEMTEST_START (60<<20)
-#define CONFIG_SYS_MEMTEST_END (70<<20)
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_SYS_DDRCDR (DDRCDR_PZ_HIZ \
- | DDRCDR_NZ_HIZ \
- | DDRCDR_Q_DRN)
- /* 0x22000001 */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-
-#define CONFIG_SYS_DDR_SIZE 512
-
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x3837c322
-#define CONFIG_SYS_DDR_TIMING_2 0x0f9848c6
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080008
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_INTERVAL 0x02000100
-
-#define CONFIG_SYS_DDR_MODE 0x04040242
-#define CONFIG_SYS_DDR_MODE2 0x00800000
-
-/* Flash */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-#define CONFIG_SYS_FLASH_SIZE 8
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 \
- | BR_MS_GPCM \
- | BR_V)
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_UPM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
-
-/*
- * U-Boot memory configuration
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#undef CONFIG_SYS_RAMBOOT
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
-
-/*
- * Local Bus LCRR and LBCR regs
- * LCRR: DLL bypass, Clock divider is 4
- * External Local Bus rate is
- * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT 0x32000000
-/* LB refresh timer prescal, 266MHz/32*/
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_CONSOLE ttyS0
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define MV_DTB_NAME "mvblm7.dtb"
-
-/*
- * PCI
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCI1_MMIO_BASE \
- (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000
-
-#define CONFIG_NET_RETRY_COUNT 3
-
-#define CONFIG_PCI_66M
-#define CONFIG_83XX_CLKIN 66666667
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-
-/* TSEC */
-#define CONFIG_GMII
-#define CONFIG_SYS_VSC8601_SKEWFIX
-#define CONFIG_SYS_VSC8601_SKEW_TX 3
-#define CONFIG_SYS_VSC8601_SKEW_RX 3
-
-#define CONFIG_TSEC1
-#define CONFIG_TSEC2
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_FEC1_PHY_NORXERR
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define TSEC1_PHY_ADDR 0x10
-#define TSEC1_PHYIDX 0
-#define TSEC1_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
-
-#define CONFIG_HAS_ETH1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define CONFIG_FEC2_PHY_NORXERR
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-#define TSEC2_PHY_ADDR 0x11
-#define TSEC2_PHYIDX 0
-#define TSEC2_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
-
-#define CONFIG_ETHPRIME "TSEC0"
-
-#define CONFIG_BOOTP_VENDOREX
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_RANDOM_DELAY
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_LIB_RAND
-
-/* USB */
-#define CONFIG_SYS_USB_HOST
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-/*
- * Environment
- */
-#undef CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0xFF800000
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-#define CONFIG_LOADS_ECHO
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_FPGA
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_USB
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_WATCHDOG
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 0x200000
-
-#define CONFIG_SYS_PROMPT "mvBL-M7> "
-#define CONFIG_SYS_CBSIZE 256
-
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-
-#define CONFIG_SYS_HRCW_LOW 0x0
-#define CONFIG_SYS_HRCW_HIGH 0x0
-
-/*
- * System performance
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
-#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
-
-/* clocking */
-#define CONFIG_SYS_SCCR_ENCCM 0
-#define CONFIG_SYS_SCCR_USBMPHCM 0
-#define CONFIG_SYS_SCCR_USBDRCM 2
-#define CONFIG_SYS_SCCR_TSEC1CM 1
-#define CONFIG_SYS_SCCR_TSEC2CM 1
-
-#define CONFIG_SYS_SICRH 0x1fef0003
-#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0)
-
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-
-#define CONFIG_SYS_HID2 HID2_HBE
-#define CONFIG_HIGH_BATS 1
-
-/* DDR */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* PCI */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* no PCI2 */
-#define CONFIG_SYS_IBAT3L 0
-#define CONFIG_SYS_IBAT3U 0
-#define CONFIG_SYS_IBAT4L 0
-#define CONFIG_SYS_IBAT4U 0
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xF0000000 \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT7L 0
-#define CONFIG_SYS_IBAT7U 0
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_NETDEV eth0
-
-/* Default path and filenames */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_RESET_TO_RETRY 1000
-
-#define MV_CI "mvBL-M7"
-#define MV_VCI "mvBL-M7"
-#define MV_FPGA_DATA 0xfff40000
-#define MV_FPGA_SIZE 0
-#define MV_KERNEL_ADDR 0xff810000
-#define MV_INITRD_ADDR 0xffb00000
-#define MV_SCRIPT_ADDR 0xff804000
-#define MV_SCRIPT_ADDR2 0xff806000
-#define MV_DTB_ADDR 0xff808000
-#define MV_INITRD_LENGTH 0x00400000
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1
-
-#define MV_KERNEL_ADDR_RAM 0x00100000
-#define MV_DTB_ADDR_RAM 0x00600000
-#define MV_INITRD_ADDR_RAM 0x01000000
-
-#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; " \
- "then source ${script_addr}; " \
- "else source ${script_addr2}; " \
- "fi;"
-#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "console_nr=0\0" \
- "baudrate=" __stringify(CONFIG_BAUDRATE) "\0" \
- "stdin=serial\0" \
- "stdout=serial\0" \
- "stderr=serial\0" \
- "fpga=0\0" \
- "fpgadata=" __stringify(MV_FPGA_DATA) "\0" \
- "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \
- "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \
- "script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \
- "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \
- "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \
- "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \
- "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \
- "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \
- "mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \
- "mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \
- "dtb_name=" __stringify(MV_DTB_NAME) "\0" \
- "mv_version=" U_BOOT_VERSION "\0" \
- "dhcp_client_id=" MV_CI "\0" \
- "dhcp_vendor-class-identifier=" MV_VCI "\0" \
- "netretry=no\0" \
- "use_static_ipaddr=no\0" \
- "static_ipaddr=192.168.90.10\0" \
- "static_netmask=255.255.255.0\0" \
- "static_gateway=0.0.0.0\0" \
- "initrd_name=uInitrd.mvBL-M7-rfs\0" \
- "zcip=no\0" \
- "netboot=yes\0" \
- "mvtest=Ff\0" \
- "tried_bootfromflash=no\0" \
- "tried_bootfromnet=no\0" \
- "bootfile=mvblm72625.boot\0" \
- "use_dhcp=yes\0" \
- "gev_start=yes\0" \
- "mvbcdma_debug=0\0" \
- "mvbcia_debug=0\0" \
- "propdev_debug=0\0" \
- "gevss_debug=0\0" \
- "watchdog=0\0" \
- "usb_dr_mode=host\0" \
- "sensor_cnt=2\0" \
- ""
-
-#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-
-#endif
projects / karo-tx-uboot.git / commitdiff