/*--------------------- Local macros and constants --------------------*/
#define _NOT_USED_ 0xFFFFFFFF
+/*------------------------- dspic io expander -----------------------*/
+#define DSPIC_PON_STATUS_REG 0x80A
+#define DSPIC_PON_INV_STATUS_REG 0x80C
+#define DSPIC_PON_KEY_REG 0x810
/*------------------------- Keyboard controller -----------------------*/
/* command codes */
#define KEYBD_CMD_READ_KEYS 0x01
/* maximum number of "magic" key codes that can be assigned */
static uchar kbd_addr = CONFIG_SYS_I2C_KEYBD_ADDR;
+static uchar dspic_addr = CONFIG_SYS_I2C_DSPIC_IO_ADDR;
static uchar *key_match (uchar *);
}
}
+
+/* Read a register from the dsPIC. */
+int _dspic_read(ushort reg, ushort *data)
+{
+ uchar buf[sizeof(*data)];
+ int rval;
+
+ if (i2c_read(dspic_addr, reg, 2, buf, 2))
+ return -1;
+
+ rval = i2c_read(dspic_addr, reg, sizeof(reg), buf, sizeof(*data));
+ *data = (buf[0] << 8) | buf[1];
+
+ return rval;
+}
+
+
/***********************************************************************
F* Function: int misc_init_r (void) P*A*Z*
*
uchar kbd_init_status = gd->kbd_status >> 8;
uchar kbd_status = gd->kbd_status;
uchar val;
+ ushort data, inv_data;
char *str;
int i;
i2c_write (kbd_addr, 0, 0, &val, 1);
i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
+ /* read out start key from bse01 received via can */
+ _dspic_read(DSPIC_PON_STATUS_REG, &data);
+ /* check highbyte from status register */
+ if (data > 0xFF) {
+ _dspic_read(DSPIC_PON_INV_STATUS_REG, &inv_data);
+
+ /* check inverse data */
+ if ((data+inv_data) == 0xFFFF) {
+ /* don't overwrite local key */
+ if (kbd_data[1] == 0) {
+ /* read key value */
+ _dspic_read(DSPIC_PON_KEY_REG, &data);
+ str = (char *)&data;
+ /* swap bytes */
+ kbd_data[1] = str[1];
+ kbd_data[2] = str[0];
+ printf("CAN received startkey: 0x%X\n", data);
+ }
+ }
+ }
+
for (i = 0; i < KEYBD_DATALEN; ++i) {
sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
}
+
setenv ("keybd", keybd_env);
str = strdup ((char *)key_match (kbd_data)); /* decode keys */
/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2010
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* This program is free software; you can redistribute it and/or
#include <asm/processor.h>
#include <asm/ppc4xx-gpio.h>
#include <asm/io.h>
+#include <post.h>
+#include <flash.h>
+#include <mtd/cfi_flash.h>
DECLARE_GLOBAL_DATA_PTR;
-extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+static phys_addr_t lwmon5_cfi_flash_bank_addr[2] = CONFIG_SYS_FLASH_BANKS_LIST;
ulong flash_get_size(ulong base, int banknum);
int misc_init_r_kbd(void);
gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1);
#if CONFIG_POST & CONFIG_SYS_POST_BSPEC1
- gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 1);
+ /* enable the LSB transmitter */
+ gpio_write_bit(CONFIG_SYS_GPIO_LSB_ENABLE, 1);
+ /* enable the CAN transmitter */
+ gpio_write_bit(CONFIG_SYS_GPIO_CAN_ENABLE, 1);
reg = 0; /* reuse as counter */
out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR,
in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR)
& ~CONFIG_SYS_DSPIC_TEST_MASK);
- while (!gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) {
+ while (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) {
udelay(1000);
}
- gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 0);
if (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY)) {
/* set "boot error" flag */
out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR,
return 0;
}
-/*---------------------------------------------------------------------------+
- | misc_init_r.
- +---------------------------------------------------------------------------*/
+/*
+ * Override weak default with board specific version
+ */
+phys_addr_t cfi_flash_bank_addr(int bank)
+{
+ return lwmon5_cfi_flash_bank_addr[bank];
+}
+
+/*
+ * Override the weak default mapping function with a board specific one
+ */
+u32 flash_get_bank_size(int cs, int idx)
+{
+ return flash_info[idx].size;
+}
+
+int board_early_init_r(void)
+{
+ u32 val0, val1;
+
+ /*
+ * lwmon5 is manufactured in 2 different board versions:
+ * The lwmon5a board has 64MiB NOR flash instead of the
+ * 128MiB of the original lwmon5. Unfortunately the CFI driver
+ * will report 2 banks of 64MiB even for the smaller flash
+ * chip, since the bank is mirrored. To fix this, we bring
+ * one bank into CFI query mode and read its response. This
+ * enables us to detect the real number of flash devices/
+ * banks which will be used later on by the common CFI driver.
+ */
+
+ /* Put bank 0 into CFI command mode and read */
+ out_be32((void *)CONFIG_SYS_FLASH0, 0x00980098);
+ val0 = in_be32((void *)CONFIG_SYS_FLASH0 + FLASH_OFFSET_CFI_RESP);
+ val1 = in_be32((void *)CONFIG_SYS_FLASH1 + FLASH_OFFSET_CFI_RESP);
+
+ /* Reset flash again out of query mode */
+ out_be32((void *)CONFIG_SYS_FLASH0, 0x00f000f0);
+
+ /* When not identical, we have 2 different flash devices/banks */
+ if (val0 != val1)
+ return 0;
+
+ /*
+ * Now we're sure that we're running on a LWMON5a board with
+ * only 64MiB NOR flash in one bank:
+ *
+ * Set flash base address and bank count for CFI driver probing.
+ */
+ cfi_flash_num_flash_banks = 1;
+ lwmon5_cfi_flash_bank_addr[0] = CONFIG_SYS_FLASH0;
+
+ return 0;
+}
+
int misc_init_r(void)
{
u32 pbcr;
u32 reg;
unsigned long usb2d0cr = 0;
unsigned long usb2phy0cr, usb2h0cr = 0;
- unsigned long sdr0_pfc1;
+ unsigned long sdr0_pfc1, sdr0_srst;
/*
* FLASH stuff...
gd->bd->bi_flashoffset = 0;
mfebc(PB0CR, pbcr);
- switch (gd->bd->bi_flashsize) {
- case 1 << 20:
- size_val = 0;
- break;
- case 2 << 20:
- size_val = 1;
- break;
- case 4 << 20:
- size_val = 2;
- break;
- case 8 << 20:
- size_val = 3;
- break;
- case 16 << 20:
- size_val = 4;
- break;
- case 32 << 20:
- size_val = 5;
- break;
- case 64 << 20:
- size_val = 6;
- break;
- case 128 << 20:
- size_val = 7;
- break;
- }
+ size_val = ffs(gd->bd->bi_flashsize) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
mtebc(PB0CR, pbcr);
flash_get_size(gd->bd->bi_flashstart, 0);
/* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET,
- -CONFIG_SYS_MONITOR_LEN,
- 0xffffffff,
- &flash_info[1]);
+ flash_protect(FLAG_PROTECT_SET, -CONFIG_SYS_MONITOR_LEN, 0xffffffff,
+ &flash_info[cfi_flash_num_flash_banks - 1]);
/* Env protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR_REDUND,
- CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[1]);
+ flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2 * CONFIG_ENV_SECT_SIZE - 1,
+ &flash_info[cfi_flash_num_flash_banks - 1]);
/*
* USB suff...
*/
+
+ /* Reset USB */
+ /* Reset of USB2PHY0 must be active at least 10 us */
+ mtsdr(SDR0_SRST0, SDR0_SRST0_USB2H | SDR0_SRST0_USB2D);
+ udelay(2000);
+
+ mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY | SDR0_SRST1_USB2HUTMI |
+ SDR0_SRST1_USB2HPHY | SDR0_SRST1_OPBA2 |
+ SDR0_SRST1_PLB42OPB1 | SDR0_SRST1_OPB2PLB40);
+ udelay(2000);
+
+ /* Errata CHIP_6 */
+
+ /* 1. Set internal PHY configuration */
/* SDR Setting */
mfsdr(SDR0_PFC1, sdr0_pfc1);
mfsdr(SDR0_USB0, usb2d0cr);
mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
mfsdr(SDR0_USB2H0CR, usb2h0cr);
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/
- usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
- usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/
-
- /* An 8-bit/60MHz interface is the only possible alternative
- when connecting the Device to the PHY */
- usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
- usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/
+ usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/
+ usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/
+ usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; /*1*/
+ usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/
+ usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
+ usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/
+
+ /*
+ * An 8-bit/60MHz interface is the only possible alternative
+ * when connecting the Device to the PHY
+ */
+ usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK;
+ usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/
mtsdr(SDR0_PFC1, sdr0_pfc1);
mtsdr(SDR0_USB0, usb2d0cr);
mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
mtsdr(SDR0_USB2H0CR, usb2h0cr);
+ /* 2. De-assert internal PHY reset */
+ mfsdr(SDR0_SRST1, sdr0_srst);
+ sdr0_srst = sdr0_srst & ~SDR0_SRST1_USB20PHY;
+ mtsdr(SDR0_SRST1, sdr0_srst);
+
+ /* 3. Wait for more than 1 ms */
+ udelay(2000);
+
+ /* 4. De-assert USB 2.0 Host main reset */
+ mfsdr(SDR0_SRST0, sdr0_srst);
+ sdr0_srst = sdr0_srst &~ SDR0_SRST0_USB2H;
+ mtsdr(SDR0_SRST0, sdr0_srst);
+ udelay(1000);
+
+ /* 5. De-assert reset of OPB2 cores */
+ mfsdr(SDR0_SRST1, sdr0_srst);
+ sdr0_srst = sdr0_srst &~ SDR0_SRST1_PLB42OPB1;
+ sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPB2PLB40;
+ sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPBA2;
+ mtsdr(SDR0_SRST1, sdr0_srst);
+ udelay(1000);
+
+ /* 6. Set EHCI Configure FLAG */
+
+ /* 7. Reassert internal PHY reset: */
+ mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY);
+ udelay(1000);
+
/*
* Clear resets
*/
- udelay (1000);
mtsdr(SDR0_SRST1, 0x00000000);
- udelay (1000);
mtsdr(SDR0_SRST0, 0x00000000);
printf("USB: Host(int phy) Device(ext phy)\n");
{
char *s = getenv("serial#");
- printf("Board: lwmon5");
+ puts("Board: lwmon5");
if (s != NULL) {
puts(", serial# ");
extern GraphicDevice mb862xx;
-static const gdc_regs init_regs [] =
-{
- {0x0100, 0x00000f00},
- {0x0020, 0x801401df},
- {0x0024, 0x00000000},
- {0x0028, 0x00000000},
- {0x002c, 0x00000000},
- {0x0110, 0x00000000},
- {0x0114, 0x00000000},
- {0x0118, 0x01df0280},
- {0x0004, 0x031f0000},
- {0x0008, 0x027f027f},
- {0x000c, 0x015f028f},
- {0x0010, 0x020c0000},
- {0x0014, 0x01df01ea},
- {0x0018, 0x00000000},
- {0x001c, 0x01e00280},
- {0x0100, 0x80010f00},
- {0x0, 0x0}
+static const gdc_regs init_regs [] = {
+ { 0x0100, 0x00000f00 },
+ { 0x0020, 0x801401df },
+ { 0x0024, 0x00000000 },
+ { 0x0028, 0x00000000 },
+ { 0x002c, 0x00000000 },
+ { 0x0110, 0x00000000 },
+ { 0x0114, 0x00000000 },
+ { 0x0118, 0x01df0280 },
+ { 0x0004, 0x031f0000 },
+ { 0x0008, 0x027f027f },
+ { 0x000c, 0x015f028f },
+ { 0x0010, 0x020c0000 },
+ { 0x0014, 0x01df01ea },
+ { 0x0018, 0x00000000 },
+ { 0x001c, 0x01e00280 },
+ { 0x0100, 0x80010f00 },
+ { 0x0, 0x0 }
};
-const gdc_regs *board_get_regs (void)
+const gdc_regs *board_get_regs(void)
{
return init_regs;
}
/* Returns Lime base address */
-unsigned int board_video_init (void)
+unsigned int board_video_init(void)
{
/*
* Reset Lime controller
return CONFIG_SYS_LIME_BASE_0;
}
-#define DEFAULT_BRIGHTNESS 0x64
+#define DEFAULT_BRIGHTNESS 0x64
static void board_backlight_brightness(int brightness)
{
}
}
-void board_backlight_switch (int flag)
+void board_backlight_switch(int flag)
{
char * param;
int rc;
/*
* Return text to be printed besides the logo.
*/
-void video_get_info_str (int line_number, char *info)
+void video_get_info_str(int line_number, char *info)
{
- if (line_number == 1) {
- strcpy (info, " Board: Lwmon5 (Liebherr Elektronik GmbH)");
- } else {
+ if (line_number == 1)
+ strcpy(info, " Board: Lwmon5 (Liebherr Elektronik GmbH)");
+ else
info [0] = '\0';
- }
}
-#endif
+#endif /* CONFIG_CONSOLE_EXTRA_INFO */
#endif /* CONFIG_VIDEO */
void board_reset(void)
/*
- * (C) Copyright 2007-2008
+ * (C) Copyright 2007-2010
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* This program is free software; you can redistribute it and/or
* MA 02111-1307 USA
*/
-/************************************************************************
+/*
* lwmon5.h - configuration for lwmon5 board
- ***********************************************************************/
+ */
#ifndef __CONFIG_H
#define __CONFIG_H
-/*-----------------------------------------------------------------------
+/*
+ * Liebherr extra version info
+ */
+#define CONFIG_IDENT_STRING " - v2.0"
+
+/*
* High Level Configuration Options
- *----------------------------------------------------------------------*/
+ */
#define CONFIG_LWMON5 1 /* Board is lwmon5 */
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-#define CONFIG_BOARD_RESET 1 /* Call board_reset */
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_early_init_f */
+#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */
+#define CONFIG_BOARD_POSTCLK_INIT /* Call board_postclk_init */
+#define CONFIG_MISC_INIT_R /* Call misc_init_r */
+#define CONFIG_BOARD_RESET /* Call board_reset */
-/*-----------------------------------------------------------------------
+/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
+ */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */
+#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
+#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* Reserved for malloc */
#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_LIME_BASE_0 0xc0000000
-#define CONFIG_SYS_LIME_BASE_1 0xc1000000
-#define CONFIG_SYS_LIME_BASE_2 0xc2000000
-#define CONFIG_SYS_LIME_BASE_3 0xc3000000
-#define CONFIG_SYS_FPGA_BASE_0 0xc4000000
-#define CONFIG_SYS_FPGA_BASE_1 0xc4200000
+#define CONFIG_SYS_LIME_BASE_0 0xc0000000
+#define CONFIG_SYS_LIME_BASE_1 0xc1000000
+#define CONFIG_SYS_LIME_BASE_2 0xc2000000
+#define CONFIG_SYS_LIME_BASE_3 0xc3000000
+#define CONFIG_SYS_FPGA_BASE_0 0xc4000000
+#define CONFIG_SYS_FPGA_BASE_1 0xc4200000
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
-#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE1 (CONFIG_SYS_PCI_MEMBASE + 0x10000000)
+#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000)
+#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000)
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
/*
+ * Initial RAM & stack pointer
+ *
* On LWMON5 we use D-cache as init-ram and stack pointer. We also move
* the POST_WORD from OCM to a 440EPx register that preserves it's
* content during reset (GPT0_COMP6). This way we reserve the OCM (16k)
*/
#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
-#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \
+ CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+/* unused GPT0 COMP reg */
#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
- /* unused GPT0 COMP reg */
-#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
- /* 440EPx errata CHIP 11 */
#define CONFIG_SYS_OCM_SIZE (16 << 10)
+/* 440EPx errata CHIP 11: don't use last 4kbytes */
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10)
/* Additional registers for watchdog timer post test */
-
#define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2)
#define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1)
#define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR
#define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300
#define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00
-/*-----------------------------------------------------------------------
+/*
* Serial Port
- *----------------------------------------------------------------------*/
+ */
#define CONFIG_CONS_INDEX 2 /* Use UART1 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
+#define CONFIG_SERIAL_MULTI
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-/*-----------------------------------------------------------------------
+/*
* Environment
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+ */
+#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */
-/*-----------------------------------------------------------------------
+/*
* FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+ */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH0 0xFC000000
#define CONFIG_SYS_FLASH1 0xF8000000
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_QUIET_TEST /* don't warn upon unknown flash */
#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-/*-----------------------------------------------------------------------
+/*
* DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
+ */
+#define CONFIG_SYS_MBYTES_SDRAM 256
#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
-#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */
-#define CONFIG_DDR_ECC 1 /* enable ECC */
-#define CONFIG_SYS_POST_ECC_ON CONFIG_SYS_POST_ECC
+#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
+#define CONFIG_DDR_ECC /* enable ECC */
/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_ECC_ON | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_FPU | \
- CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_OCM | \
- CONFIG_SYS_POST_RTC | \
- CONFIG_SYS_POST_SPR | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_SYSMON | \
- CONFIG_SYS_POST_WATCHDOG | \
- CONFIG_SYS_POST_DSP | \
- CONFIG_SYS_POST_BSPEC1 | \
- CONFIG_SYS_POST_BSPEC2 | \
- CONFIG_SYS_POST_BSPEC3 | \
- CONFIG_SYS_POST_BSPEC4 | \
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_ECC | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_FPU | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_OCM | \
+ CONFIG_SYS_POST_RTC | \
+ CONFIG_SYS_POST_SPR | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_SYSMON | \
+ CONFIG_SYS_POST_WATCHDOG | \
+ CONFIG_SYS_POST_DSP | \
+ CONFIG_SYS_POST_BSPEC1 | \
+ CONFIG_SYS_POST_BSPEC2 | \
+ CONFIG_SYS_POST_BSPEC3 | \
+ CONFIG_SYS_POST_BSPEC4 | \
CONFIG_SYS_POST_BSPEC5)
-#define CONFIG_POST_WATCHDOG {\
+/* Define here the base-addresses of the UARTs to test in POST */
+#define CONFIG_SYS_POST_UART_TABLE { UART0_BASE, UART1_BASE }
+
+#define CONFIG_POST_WATCHDOG { \
"Watchdog timer test", \
"watchdog", \
"This test checks the watchdog timer.", \
&lwmon5_watchdog_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_WATCHDOG \
+ CONFIG_SYS_POST_WATCHDOG \
}
-#define CONFIG_POST_BSPEC1 {\
+#define CONFIG_POST_BSPEC1 { \
"dsPIC init test", \
"dspic_init", \
"This test returns result of dsPIC READY test run earlier.", \
&dspic_init_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_BSPEC1 \
+ CONFIG_SYS_POST_BSPEC1 \
}
-#define CONFIG_POST_BSPEC2 {\
+#define CONFIG_POST_BSPEC2 { \
"dsPIC test", \
"dspic", \
"This test gets result of dsPIC POST and dsPIC version.", \
&dspic_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_BSPEC2 \
+ CONFIG_SYS_POST_BSPEC2 \
}
-#define CONFIG_POST_BSPEC3 {\
+#define CONFIG_POST_BSPEC3 { \
"FPGA test", \
"fpga", \
"This test checks FPGA registers and memory.", \
- POST_RAM | POST_ALWAYS, \
+ POST_RAM | POST_ALWAYS | POST_MANUAL, \
&fpga_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_BSPEC3 \
+ CONFIG_SYS_POST_BSPEC3 \
}
-#define CONFIG_POST_BSPEC4 {\
+#define CONFIG_POST_BSPEC4 { \
"GDC test", \
"gdc", \
"This test checks GDC registers and memory.", \
- POST_RAM | POST_ALWAYS, \
+ POST_RAM | POST_ALWAYS | POST_MANUAL,\
&gdc_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_BSPEC4 \
+ CONFIG_SYS_POST_BSPEC4 \
}
-#define CONFIG_POST_BSPEC5 {\
+#define CONFIG_POST_BSPEC5 { \
"SYSMON1 test", \
"sysmon1", \
"This test checks GPIO_62_EPX pin indicating power failure.", \
&sysmon1_post_test, \
NULL, \
NULL, \
- CONFIG_SYS_POST_BSPEC5 \
+ CONFIG_SYS_POST_BSPEC5 \
}
#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE)
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-/*-----------------------------------------------------------------------
+/*
* I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+ */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */
+#define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */
+#define CONFIG_SYS_I2C_EEPROM_MB_ADDR 0x53 /* EEPROM AT24C128 (MainBoard) */
+#define CONFIG_SYS_I2C_DSPIC_ADDR 0x54 /* dsPIC */
+#define CONFIG_SYS_I2C_DSPIC_2_ADDR 0x55 /* dsPIC */
+#define CONFIG_SYS_I2C_DSPIC_KEYB_ADDR 0x56 /* dsPIC */
+#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* dsPIC */
+
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */
/* 64 byte page write mode using*/
/* last 6 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
+
+#define CONFIG_RTC_PCF8563 /* enable Philips PCF8563 RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
+#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
+#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */
+
+#define I2C_ADDR_LIST { \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_CPU_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_MB_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_2_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_KEYB_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_IO_ADDR }
-#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
-#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
-#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+/* Update size in "reg" property of NOR FLASH device tree nodes */
+#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */
-#if 0
-#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */
-#define CONFIG_AUTOBOOT_PROMPT \
- "\nEnter password - autoboot in %d sec...\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */
-#endif
#define CONFIG_PREBOOT "setenv bootdelay 15"
"cp.b 200000 FFF80000 80000\0" \
"upd=run load update\0" \
"lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \
- "source 200000\0" \
+ "autoscr 200000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_USB
#endif
-/*-----------------------------------------------------------------------
+/*
* Miscellaneous configurable options
- *----------------------------------------------------------------------*/
+ */
#define CONFIG_SUPPORT_VFAT
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-/*-----------------------------------------------------------------------
+/*
* PCI stuff
- *----------------------------------------------------------------------*/
+ */
/* General PCI */
#define CONFIG_PCI /* include pci support */
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
+#ifndef DEBUG
#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */
+#endif
#define CONFIG_WD_PERIOD 40000 /* in usec */
#define CONFIG_WD_MAX_RATE 66600 /* in ticks */
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the 40x Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-/*-----------------------------------------------------------------------
+/*
* External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
+ */
#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x03050200
+#define CONFIG_SYS_EBC_PB0AP 0x03000280
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000)
/* Memory Bank 1 (Lime) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x01004380
-#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xdc000)
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xbc000)
/* Memory Bank 2 (FPGA) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x01004400
#define CONFIG_SYS_EBC_CFG 0xb8400000
-/*-----------------------------------------------------------------------
+/*
* Graphics (Fujitsu Lime)
- *----------------------------------------------------------------------*/
+ */
+/* SDRAM Clock frequency adjustment register */
+#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038
+#if 1 /* 133MHz is not tested enough, use 100MHz for now */
/* Lime Clock frequency is to set 100MHz */
#define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000
-#if 0
+#else
/* Lime Clock frequency for 133MHz */
#define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000
#endif
-/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars
- and pixel flare on display when 133MHz was configured. According to
- SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */
+/* SDRAM Parameter register */
+#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC
+/*
+ * SDRAM parameter value; was 0x414FB7F2, caused several vertical bars
+ * and pixel flare on display when 133MHz was configured. According to
+ * SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed
+ * Grade
+ */
#ifdef CONFIG_SYS_LIME_CLOCK_133MHZ
#define CONFIG_SYS_MB862xx_MMR 0x414FB7F3
#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ
#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ
#endif
-/*-----------------------------------------------------------------------
+/*
* GPIO Setup
- *----------------------------------------------------------------------*/
+ */
#define CONFIG_SYS_GPIO_PHY1_RST 12
#define CONFIG_SYS_GPIO_FLASH_WP 14
#define CONFIG_SYS_GPIO_PHY0_RST 22
#define CONFIG_SYS_GPIO_DSPIC_READY 51
+#define CONFIG_SYS_GPIO_CAN_ENABLE 53
+#define CONFIG_SYS_GPIO_LSB_ENABLE 54
#define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55
#define CONFIG_SYS_GPIO_HIGHSIDE 56
#define CONFIG_SYS_GPIO_EEPROM_INT_WP 57
#define CONFIG_SYS_GPIO_SYSMON_STATUS 62
#define CONFIG_SYS_GPIO_WATCHDOG 63
-/*-----------------------------------------------------------------------
+/*
* PPC440 GPIO Configuration
*/
#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
DECLARE_GLOBAL_DATA_PTR;
-#define DSP_STATUS_REG 0xC4000008
+#define DSP_STATUS_REG 0xC4000008
+#define FPGA_STATUS_REG 0xC400000C
int dsp_post_test(int flags)
{
+ uint old_value;
uint read_value;
int ret;
+ /* momorize fpga status */
+ old_value = in_be32((void *)FPGA_STATUS_REG);
+ /* enable outputs */
+ out_be32((void *)FPGA_STATUS_REG, 0x30);
+
+ /* generate sync signal */
+ out_be32((void *)DSP_STATUS_REG, 0x300);
+ udelay(5);
+ out_be32((void *)DSP_STATUS_REG, 0);
+ udelay(500);
+
+ /* read status */
ret = 0;
read_value = in_be32((void *)DSP_STATUS_REG) & 0x3;
- if (read_value != 0x3) {
+ if (read_value != 0x03) {
post_log("\nDSP status read %08X\n", read_value);
ret = 1;
}
+ /* restore fpga status */
+ out_be32((void *)FPGA_STATUS_REG, old_value);
+
return ret;
}
#define DSPIC_POST_ERROR_REG 0x800
#define DSPIC_SYS_ERROR_REG 0x802
-#define DSPIC_VERSION_REG 0x804
+#define DSPIC_SYS_VERSION_REG 0x804
+#define DSPIC_FW_VERSION_REG 0x808
#if CONFIG_POST & CONFIG_SYS_POST_BSPEC1
/* Verify that dsPIC ready test done early at hw init passed ok */
int dspic_init_post_test(int flags)
{
- if (in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) & CONFIG_SYS_DSPIC_TEST_MASK) {
+ if (in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) &
+ CONFIG_SYS_DSPIC_TEST_MASK) {
post_log("dsPIC init test failed\n");
return 1;
}
#if CONFIG_POST & CONFIG_SYS_POST_BSPEC2
/* Read a register from the dsPIC. */
-int dspic_read(ushort reg)
+int dspic_read(ushort reg, ushort *data)
{
- uchar buf[2];
+ uchar buf[sizeof(*data)];
+ int rval;
if (i2c_read(CONFIG_SYS_I2C_DSPIC_IO_ADDR, reg, 2, buf, 2))
return -1;
+ rval = i2c_read(CONFIG_SYS_I2C_DSPIC_IO_ADDR, reg, sizeof(reg),
+ buf, sizeof(*data));
+ *data = (buf[0] << 8) | buf[1];
- return (uint)((buf[0] << 8) | buf[1]);
+ return rval;
}
/* Verify error codes regs, display version */
int dspic_post_test(int flags)
{
- int data;
+ ushort data;
int ret = 0;
post_log("\n");
- data = dspic_read(DSPIC_VERSION_REG);
- if (data == -1) {
- post_log("dsPIC : failed read version\n");
+
+ /* read dspic FW-Version */
+ if (dspic_read(DSPIC_FW_VERSION_REG, &data)) {
+ post_log("dsPIC: failed read FW-Version\n");
+ ret = 1;
+ } else {
+ post_log("dsPIC FW-Version: %u.%u\n",
+ (data >> 8) & 0xFF, data & 0xFF);
+ }
+
+ /* read dspic SYS-Version */
+ if (dspic_read(DSPIC_SYS_VERSION_REG, &data)) {
+ post_log("dsPIC: failed read version\n");
ret = 1;
} else {
- post_log("dsPIC version: %u.%u\n",
- (data >> 8) & 0xFF, data & 0xFF);
+ post_log("dsPIC SYS-Version: %u.%u\n",
+ (data >> 8) & 0xFF, data & 0xFF);
}
- data = dspic_read(DSPIC_POST_ERROR_REG);
- if (data != 0) ret = 1;
- if (data == -1) {
- post_log("dsPIC : failed read POST code\n");
+ /* read dspic POST error code */
+ if (dspic_read(DSPIC_POST_ERROR_REG, &data)) {
+ post_log("dsPIC: failed read POST code\n");
+ ret = 1;
} else {
- post_log("dsPIC POST code 0x%04X\n", data);
+ post_log("dsPIC POST-ERROR code: 0x%04X\n", data);
}
- data = dspic_read(DSPIC_SYS_ERROR_REG);
- if (data == -1) {
- post_log("dsPIC : failed read system error\n");
+ /* read dspic SYS error code */
+ if ((data = dspic_read(DSPIC_SYS_ERROR_REG, &data))) {
+ post_log("dsPIC: failed read system error\n");
ret = 1;
} else {
- post_log("dsPIC SYS-ERROR code: 0x%04X\n", data);
+ post_log("dsPIC SYS-ERROR code: 0x%04X\n", data);
}
return ret;
*/
#include <post.h>
-
+#include <watchdog.h>
#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
#define FPGA_RAM_START 0xC4200000
#define FPGA_RAM_END 0xC4203FFF
#define FPGA_STAT 0xC400000C
+#define FPGA_BUFFER 0x00800000
+#define FPGA_RAM_SIZE (FPGA_RAM_END - FPGA_RAM_START + 1)
#if CONFIG_POST & CONFIG_SYS_POST_BSPEC3
-/* Testpattern for fpga memorytest */
-static uint pattern[] = {
+const static unsigned long pattern[] = {
+ 0xffffffff,
+ 0xaaaaaaaa,
+ 0xcccccccc,
+ 0xf0f0f0f0,
+ 0xff00ff00,
+ 0xffff0000,
+ 0x0000ffff,
+ 0x00ff00ff,
+ 0x0f0f0f0f,
+ 0x33333333,
0x55555555,
- 0xAAAAAAAA,
- 0xAA5555AA,
- 0x55AAAA55,
- 0x0
+ 0x00000000,
};
+const static unsigned long otherpattern = 0x01234567;
+
static int one_scratch_test(uint value)
{
uint read_value;
read_value = in_be32((void *)FPGA_SCRATCH_REG);
if (read_value != value) {
post_log("FPGA SCRATCH test failed write %08X, read %08X\n",
- value, read_value);
- ret = 1;
+ value, read_value);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+static int fpga_post_test1(ulong *start, ulong size, ulong val)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = val;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != val) {
+ post_log("FPGA Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, val, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+ return ret;
+}
+
+static int fpga_post_test2(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = 1 << (i % 32);
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != 1 << (i % 32)) {
+ post_log("FPGA Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, 1 << (i % 32), readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+static int fpga_post_test3(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = i;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != i) {
+ post_log("FPGA Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, i, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+static int fpga_post_test4(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = ~i;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != ~i) {
+ post_log("FPGA Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, ~i, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
}
return ret;
}
/* FPGA Memory-pattern-test */
-static int fpga_mem_test(void * address)
+static int fpga_mem_test(void)
{
- int ret = 1;
- uint read_value;
- uint old_value;
- uint i = 0;
- /* save content */
- old_value = in_be32(address);
-
- while (pattern[i] != 0) {
- out_be32(address, pattern[i]);
- /* read other location (protect against data lines capacity) */
- ret = in_be16((void *)FPGA_VERSION_REG);
- /* verify test pattern */
- read_value = in_be32(address);
-
- if (read_value != pattern[i]) {
- post_log("FPGA Memory test failed.");
- post_log(" write %08X, read %08X at address %08X\n",
- pattern[i], read_value, address);
+ int ret = 0;
+ ulong* start = (ulong *)FPGA_RAM_START;
+ ulong size = FPGA_RAM_SIZE;
+
+ if (ret == 0)
+ ret = fpga_post_test1(start, size, 0x00000000);
+
+ if (ret == 0)
+ ret = fpga_post_test1(start, size, 0xffffffff);
+
+ if (ret == 0)
+ ret = fpga_post_test1(start, size, 0x55555555);
+
+ if (ret == 0)
+ ret = fpga_post_test1(start, size, 0xaaaaaaaa);
+
+ WATCHDOG_RESET();
+
+ if (ret == 0)
+ ret = fpga_post_test2(start, size);
+
+ if (ret == 0)
+ ret = fpga_post_test3(start, size);
+
+ if (ret == 0)
+ ret = fpga_post_test4(start, size);
+
+ return ret;
+}
+
+
+
+/* Verify FPGA addresslines */
+static int fpga_post_addrline(ulong *address, ulong *base, ulong size)
+{
+ unsigned long *target;
+ unsigned long *end;
+ unsigned long readback;
+ unsigned long xor;
+ int ret = 0;
+
+ end = (ulong *)((ulong)base + size);
+ xor = 0;
+
+ for (xor = sizeof(ulong); xor > 0; xor <<= 1) {
+ target = (ulong*)((ulong)address ^ xor);
+ if ((target >= base) && (target < end)) {
+ *address = ~*target;
+ readback = *target;
+
+ if (readback == *address) {
+ post_log("Memory (address line) error at %08x"
+ "XOR value %08x !\n",
+ address, target, xor);
+ ret = -1;
+ break;
+ }
+ }
+ }
+
+ return ret;
+}
+
+/* Verify FPGA addresslines */
+static int fpga_post_dataline(ulong *address)
+{
+ unsigned long temp32 = 0;
+ int i = 0;
+ int ret = 0;
+
+ for (i = 0; i < ARRAY_SIZE(pattern); i++) {
+ *address = pattern[i];
+ /*
+ * Put a different pattern on the data lines: otherwise they
+ * may float long enough to read back what we wrote.
+ */
+ *(address + 1) = otherpattern;
+ temp32 = *address;
+
+ if (temp32 != pattern[i]){
+ post_log("Memory (date line) error at %08x, "
+ "wrote %08x, read %08x !\n",
+ address, pattern[i], temp32);
ret = 1;
- goto out;
}
- i++;
}
- ret = 0;
-out:
- out_be32(address, old_value);
return ret;
}
+
/* Verify FPGA, get version & memory size */
int fpga_post_test(int flags)
{
- uint address;
uint old_value;
- ushort version;
+ uint version;
uint read_value;
int ret = 0;
out_be32((void *)FPGA_SCRATCH_REG, old_value);
- version = in_be16((void *)FPGA_VERSION_REG);
- post_log("FPGA : version %u.%u\n",
- (version >> 8) & 0xFF, version & 0xFF);
+ version = in_be32((void *)FPGA_VERSION_REG);
+ post_log("FPGA version %u.%u\n",
+ (version >> 8) & 0xFF, version & 0xFF);
/* Enable write to FPGA RAM */
out_be32((void *)FPGA_STAT, in_be32((void *)FPGA_STAT) | 0x1000);
- read_value = get_ram_size((void *)CONFIG_SYS_FPGA_BASE_1, 0x4000);
- post_log("FPGA RAM size: %d bytes\n", read_value);
+ /* get RAM size */
+ read_value = get_ram_size((void *)CONFIG_SYS_FPGA_BASE_1, FPGA_RAM_SIZE);
+ post_log("FPGA RAM size %d bytes\n", read_value);
+ WATCHDOG_RESET();
- for (address = 0; address < 0x1000; address++) {
- if (fpga_mem_test((void *)(FPGA_RAM_START + 4*address)) == 1) {
- ret = 1;
- goto out;
- }
+ /* copy fpga memory to DDR2 RAM*/
+ memcpy((void *)FPGA_BUFFER,(void *)FPGA_RAM_START, FPGA_RAM_SIZE);
+ WATCHDOG_RESET();
+
+ /* Test datalines */
+ if (fpga_post_dataline((ulong *)FPGA_RAM_START)) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+
+ /* Test addresslines */
+ if (fpga_post_addrline((ulong *)FPGA_RAM_START,
+ (ulong *)FPGA_RAM_START, FPGA_RAM_SIZE)) {
+ ret = 1;
+ goto out;
}
+ WATCHDOG_RESET();
+ if (fpga_post_addrline((ulong *)FPGA_RAM_END - sizeof(long),
+ (ulong *)FPGA_RAM_START, FPGA_RAM_SIZE)) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+
+ /* Memory Pattern Test */
+ if (fpga_mem_test()) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+
+ /* restore memory */
+ memcpy((void *)FPGA_RAM_START,(void *)FPGA_BUFFER, FPGA_RAM_SIZE);
+ WATCHDOG_RESET();
out:
+ /* Disable write to RAM */
+ out_be32((void *)FPGA_STAT, in_be32((void *)FPGA_STAT) & 0xEFFF);
return ret;
}
*/
#include <post.h>
-
+#include <watchdog.h>
#include <asm/io.h>
+#include <video.h>
DECLARE_GLOBAL_DATA_PTR;
-#define GDC_SCRATCH_REG 0xC1FF8044
-#define GDC_VERSION_REG 0xC1FF8084
-#define GDC_RAM_START 0xC0000000
-#define GDC_RAM_END 0xC2000000
+#define GDC_SCRATCH_REG 0xC1FF8044
+#define GDC_VERSION_REG 0xC1FF8084
+#define GDC_HOST_BASE 0xC1FC0000
+#define GDC_RAM_START 0xC0000000
+#define GDC_RAM_END (GDC_HOST_BASE - 1)
+#define GDC_RAM_SIZE (GDC_RAM_END - GDC_RAM_START)
#if CONFIG_POST & CONFIG_SYS_POST_BSPEC4
+const static unsigned long pattern[] = {
+ 0xffffffff,
+ 0xaaaaaaaa,
+ 0xcccccccc,
+ 0xf0f0f0f0,
+ 0xff00ff00,
+ 0xffff0000,
+ 0x0000ffff,
+ 0x00ff00ff,
+ 0x0f0f0f0f,
+ 0x33333333,
+ 0x55555555,
+ 0x00000000
+};
+
+const static unsigned long otherpattern = 0x01234567;
+
+/* test write/read og a given LIME Register */
static int gdc_test_reg_one(uint value)
{
int ret;
read_value = in_be32((void *)GDC_SCRATCH_REG);
if (read_value != value) {
post_log("GDC SCRATCH test failed write %08X, read %08X\n",
- value, read_value);
+ value, read_value);
}
return (read_value != value);
}
-/* Verify GDC, get memory size */
+/* test with a given static 32 bit pattern in a given memory addressrange */
+static int gdc_post_test1(ulong *start, ulong size, ulong val)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = val;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != val) {
+ post_log("GDC Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, val, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+/* test with dynamic 32 bit pattern in a given memory addressrange */
+static int gdc_post_test2(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = 1 << (i % 32);
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != 1 << (i % 32)) {
+ post_log("GDC Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, 1 << (i % 32), readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+/* test with dynamic 32 bit pattern in a given memory addressrange */
+static int gdc_post_test3(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = i;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != i) {
+ post_log("GDC Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, i, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+/* test with dynamic 32 bit pattern in a given memory addressrange */
+static int gdc_post_test4(ulong *start, ulong size)
+{
+ int ret = 0;
+ ulong i = 0;
+ ulong *mem = start;
+ ulong readback;
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ mem[i] = ~i;
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ for (i = 0; i < size / sizeof(ulong); i++) {
+ readback = mem[i];
+ if (readback != ~i) {
+ post_log("GDC Memory error at %08x, "
+ "wrote %08x, read %08x !\n",
+ mem + i, ~i, readback);
+ ret = -1;
+ break;
+ }
+ if (i % 1024 == 0)
+ WATCHDOG_RESET();
+ }
+
+ return ret;
+}
+
+/* do some patterntests in a given addressrange */
+int gdc_mem_test(ulong *start, ulong size)
+{
+ int ret = 0;
+
+ /*
+ * check addressrange and do different static and dynamic
+ * pattern tests with it.
+ */
+ if (((void *)start) + size <= (void *)GDC_RAM_END) {
+ if (ret == 0)
+ ret = gdc_post_test1(start, size, 0x00000000);
+
+ if (ret == 0)
+ ret = gdc_post_test1(start, size, 0xffffffff);
+
+ if (ret == 0)
+ ret = gdc_post_test1(start, size, 0x55555555);
+
+ if (ret == 0)
+ ret = gdc_post_test1(start, size, 0xaaaaaaaa);
+
+ if (ret == 0)
+ ret = gdc_post_test2(start, size);
+
+ if (ret == 0)
+ ret = gdc_post_test3(start, size);
+
+ if (ret == 0)
+ ret = gdc_post_test4(start, size);
+ }
+
+ return ret;
+}
+
+/* test function of gdc memory addresslines*/
+static int gdc_post_addrline(ulong *address, ulong *base, ulong size)
+{
+ ulong *target;
+ ulong *end;
+ ulong readback = 0;
+ ulong xor = 0;
+ int ret = 0;
+
+ end = (ulong *)((ulong)base + size);
+
+ for (xor = sizeof(long); xor > 0; xor <<= 1) {
+ target = (ulong *)((ulong)address ^ xor);
+ if ((target >= base) && (target < end)) {
+ *address = ~*target;
+ readback = *target;
+ }
+
+ if (readback == *address) {
+ post_log("GDC Memory (address line) error at %08x"
+ "XOR value %08x !\n",
+ address, target , xor);
+ ret = -1;
+ break;
+ }
+ }
+
+ return ret;
+}
+
+static int gdc_post_dataline(ulong *address)
+{
+ unsigned long temp32 = 0;
+ int i = 0;
+ int ret = 0;
+
+ for (i = 0; i < ARRAY_SIZE(pattern); i++) {
+ *address = pattern[i];
+ /*
+ * Put a different pattern on the data lines: otherwise they
+ * may float long enough to read back what we wrote.
+ */
+ *(address + 1) = otherpattern;
+ temp32 = *address;
+
+ if (temp32 != pattern[i]){
+ post_log("GDC Memory (date line) error at %08x, "
+ "wrote %08x, read %08x !\n",
+ address, pattern[i], temp32);
+ ret = 1;
+ }
+ }
+
+ return ret;
+}
+
+/* Verify GDC, get memory size, verify GDC memory */
int gdc_post_test(int flags)
{
- uint old_value;
- int ret = 0;
+ uint old_value;
+ int i = 0;
+ int ret = 0;
post_log("\n");
old_value = in_be32((void *)GDC_SCRATCH_REG);
old_value = in_be32((void *)GDC_VERSION_REG);
post_log("GDC chip version %u.%u, year %04X\n",
- (old_value >> 8) & 0xFF, old_value & 0xFF,
- (old_value >> 16) & 0xFFFF);
+ (old_value >> 8) & 0xFF, old_value & 0xFF,
+ (old_value >> 16) & 0xFFFF);
old_value = get_ram_size((void *)GDC_RAM_START,
- GDC_RAM_END - GDC_RAM_START);
+ 0x02000000);
+
+ debug("GDC RAM size (ist): %d bytes\n", old_value);
+ debug("GDC RAM size (soll): %d bytes\n", GDC_RAM_SIZE);
post_log("GDC RAM size: %d bytes\n", old_value);
+ /* Test SDRAM datalines */
+ if (gdc_post_dataline((ulong *)GDC_RAM_START)) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+
+ /* Test SDRAM adresslines */
+ if (gdc_post_addrline((ulong *)GDC_RAM_START,
+ (ulong *)GDC_RAM_START, GDC_RAM_SIZE)) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+ if (gdc_post_addrline((ulong *)GDC_RAM_END - sizeof(long),
+ (ulong *)GDC_RAM_START, GDC_RAM_SIZE)) {
+ ret = 1;
+ goto out;
+ }
+ WATCHDOG_RESET();
+
+ /* memory pattern test */
+ debug("GDC Memory test (flags %8x:%8x)\n", flags,
+ POST_SLOWTEST | POST_MANUAL);
+
+ if (flags & POST_MANUAL) {
+ debug("Full memory test\n");
+ if (gdc_mem_test((ulong *)GDC_RAM_START, GDC_RAM_SIZE)) {
+ ret = 1;
+ goto out;
+ }
+ /* load splashscreen again */
+ } else {
+ debug("smart memory test\n");
+ for (i = 0; i < (GDC_RAM_SIZE >> 20) && ret == 0; i++) {
+ if (ret == 0)
+ ret = gdc_mem_test((ulong *)(GDC_RAM_START +
+ (i << 20)),
+ 0x800);
+ if (ret == 0)
+ ret = gdc_mem_test((ulong *)(GDC_RAM_START +
+ (i << 20) + 0xff800),
+ 0x800);
+ }
+ }
+ WATCHDOG_RESET();
+
+out:
return ret;
}
#endif /* CONFIG_POST & CONFIG_SYS_POST_BSPEC4 */
DECLARE_GLOBAL_DATA_PTR;
/* from dspic.c */
-extern int dspic_read(ushort reg);
+extern int dspic_read(ushort reg, ushort *data);
#define REG_TEMPERATURE 0x12BC
#define REG_VOLTAGE_5V 0x12CA
typedef struct sysmon_s sysmon_t;
typedef struct sysmon_table_s sysmon_table_t;
-static void sysmon_dspic_init (sysmon_t * this);
-static int sysmon_dspic_read (sysmon_t * this, uint addr);
-static void sysmon_backlight_disable (sysmon_table_t * this);
+static void sysmon_dspic_init(sysmon_t *this);
+static int sysmon_dspic_read(sysmon_t *this, uint addr, int *val);
+static int sysmon_dspic_read_sgn(sysmon_t *this, uint addr, int *val);
+static void sysmon_backlight_disable(sysmon_table_t *this);
-struct sysmon_s
-{
+struct sysmon_s {
uchar chip;
void (*init)(sysmon_t *);
- int (*read)(sysmon_t *, uint);
+ int (*read)(sysmon_t *, uint, int *);
};
-static sysmon_t sysmon_dspic =
- {CONFIG_SYS_I2C_DSPIC_IO_ADDR, sysmon_dspic_init, sysmon_dspic_read};
+static sysmon_t sysmon_dspic = {
+ CONFIG_SYS_I2C_DSPIC_IO_ADDR,
+ sysmon_dspic_init,
+ sysmon_dspic_read
+};
-static sysmon_t * sysmon_list[] =
-{
+static sysmon_t sysmon_dspic_sgn = {
+ CONFIG_SYS_I2C_DSPIC_IO_ADDR,
+ sysmon_dspic_init,
+ sysmon_dspic_read_sgn
+};
+
+static sysmon_t *sysmon_list[] = {
&sysmon_dspic,
NULL
};
-struct sysmon_table_s
-{
- char * name;
- char * unit_name;
- sysmon_t * sysmon;
+struct sysmon_table_s {
+ char *name;
+ char *unit_name;
+ sysmon_t *sysmon;
void (*exec_before)(sysmon_table_t *);
void (*exec_after)(sysmon_table_t *);
uint addr;
};
-static sysmon_table_t sysmon_table[] =
-{
+static sysmon_table_t sysmon_table[] = {
{
- "Temperature", " C", &sysmon_dspic, NULL, sysmon_backlight_disable,
- 1, 1, -32768, 32767, 0xFFFF,
- 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0,
- 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0,
- REG_TEMPERATURE,
+ "Temperature", " C", &sysmon_dspic, NULL, sysmon_backlight_disable,
+ 1, 1, -32768, 32767, 0xFFFF,
+ 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0,
+ 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0,
+ REG_TEMPERATURE,
},
{
- "+ 5 V", "V", &sysmon_dspic, NULL, NULL,
- 100, 1000, -0x8000, 0x7FFF, 0xFFFF,
- 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0,
- 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0,
- REG_VOLTAGE_5V,
+ "+ 5 V", "V", &sysmon_dspic, NULL, NULL,
+ 100, 1000, -0x8000, 0x7FFF, 0xFFFF,
+ 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0,
+ 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0,
+ REG_VOLTAGE_5V,
},
{
- "+ 5 V standby", "V", &sysmon_dspic, NULL, NULL,
- 100, 1000, -0x8000, 0x7FFF, 0xFFFF,
- 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0,
- 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0,
- REG_VOLTAGE_5V_STANDBY,
+ "+ 5 V standby", "V", &sysmon_dspic, NULL, NULL,
+ 100, 1000, -0x8000, 0x7FFF, 0xFFFF,
+ 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0,
+ 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0,
+ REG_VOLTAGE_5V_STANDBY,
+ },
+
+ {
+ "Temperature", "°C", &sysmon_dspic_sgn, NULL, sysmon_backlight_disable,
+ 1, 1, -32768, 32767, 0xFFFF,
+ 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0,
+ 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0,
+ REG_TEMPERATURE,
},
};
-static int sysmon_table_size = sizeof(sysmon_table) / sizeof(sysmon_table[0]);
-int sysmon_init_f (void)
+int sysmon_init_f(void)
{
- sysmon_t ** l;
+ sysmon_t **l;
for (l = sysmon_list; *l; l++)
(*l)->init(*l);
return 0;
}
-void sysmon_reloc (void)
+void sysmon_reloc(void)
{
/* Do nothing for now, sysmon_reloc() is required by the sysmon post */
}
-static char *sysmon_unit_value (sysmon_table_t *s, uint val)
+static char *sysmon_unit_value(sysmon_table_t *s, uint val)
{
static char buf[32];
char *p, sign;
if (unit_val < 0) {
sign = '-';
unit_val = -unit_val;
- } else
+ } else {
sign = '+';
+ }
p = buf + sprintf(buf, "%c%2d", sign, unit_val / s->unit_div);
-
frac = unit_val % s->unit_div;
-
frac /= (s->unit_div / s->unit_precision);
decimal = s->unit_precision;
return buf;
}
-static void sysmon_dspic_init (sysmon_t * this)
+static void sysmon_dspic_init(sysmon_t *this)
{
}
-static int sysmon_dspic_read (sysmon_t * this, uint addr)
+static int sysmon_dspic_read(sysmon_t *this, uint addr, int *val)
{
- int res = dspic_read(addr);
+ ushort data;
+
+ if (dspic_read(addr, &data) == 0){
+ /* To fit into the table range we should add 0x8000 */
+ *val = data + 0x8000;
+ return 0;
+ }
- /* To fit into the table range we should add 0x8000 */
- return (res == -1) ? -1 : (res + 0x8000);
+ return -1;
}
-static void sysmon_backlight_disable (sysmon_table_t * this)
+static int sysmon_dspic_read_sgn(sysmon_t *this, uint addr, int *val)
+{
+ ushort data;
+
+ if (dspic_read(addr, &data) == 0){
+ /* To fit into the table range we should add 0x8000 */
+ *val = (signed short)data + 0x8000;
+ return 0;
+ }
+
+ return -1;
+}
+
+static void sysmon_backlight_disable(sysmon_table_t *this)
{
#if defined(CONFIG_VIDEO)
board_backlight_switch(this->val_valid_alt);
#endif
}
-int sysmon_post_test (int flags)
+int sysmon_post_test(int flags)
{
int res = 0;
sysmon_table_t * t;
int val;
- for (t = sysmon_table; t < sysmon_table + sysmon_table_size; t ++) {
+ for (t = sysmon_table; t < sysmon_table + ARRAY_SIZE(sysmon_table); t++) {
+ t->val_valid = 1;
if (t->exec_before)
t->exec_before(t);
- val = t->sysmon->read(t->sysmon, t->addr);
- if (val != -1) {
- t->val_valid = val >= t->val_min && val <= t->val_max;
- t->val_valid_alt = val >= t->val_min_alt && val <= t->val_max_alt;
- } else {
+ if (t->sysmon->read(t->sysmon, t->addr, &val) != 0) {
t->val_valid = 0;
t->val_valid_alt = 0;
+ post_log(": read failed\n");
+ res = 1;
+ break;
+ }
+
+ if (t->val_valid != 0) {
+ t->val_valid = val >= t->val_min && val <= t->val_max;
+ t->val_valid_alt = val >= t->val_min_alt && val <= t->val_max_alt;
}
if (t->exec_after)
t->exec_after(t);
- if ((!t->val_valid) || (flags & POST_MANUAL)) {
- printf("%-17s = %-10s ", t->name, sysmon_unit_value(t, val));
- printf("allowed range");
- printf(" %-8s ..", sysmon_unit_value(t, t->val_min));
- printf(" %-8s", sysmon_unit_value(t, t->val_max));
- printf(" %s\n", t->val_valid ? "OK" : "FAIL");
+ if ((!t->val_valid) || (flags)) {
+ post_log("\n\t%-17s = %-10s ", t->name, sysmon_unit_value(t, val));
+ post_log("allowed range");
+ post_log(" %-8s ..", sysmon_unit_value(t, t->val_min));
+ post_log(" %-8s", sysmon_unit_value(t, t->val_max));
+ post_log(" %s", t->val_valid ? "OK" : "FAIL");
}
- if (!t->val_valid)
+ if (!t->val_valid) {
res = 1;
+ break;
+ }
}
+ post_log("\n");
return res;
}
* 3.1. GPIO62 is low
* Assuming system voltage failure.
*/
- post_log("Abnormal voltage detected (GPIO62)\n");
+ post_log("sysmon1 Abnormal voltage detected (GPIO62)\n");
+ post_log("POST sysmon1 FAILED\n");
return 1;
+ } else {
+ post_log("sysmon1 PASSED\n");
}
return 0;
ulong time;
/* 3.3.1. So, the test succeed, save measured time to syslog. */
time = in_be32((void *)CONFIG_SYS_WATCHDOG_TIME_ADDR);
- post_log("hw watchdog time : %u ms, passed ", time);
- /* 3.3.2. Set scratch register 1 to 0x0000xxxx */
- watchdog_magic_write(0);
- return 0;
+ if (time > 90 ) { /* ms*/
+ post_log("hw watchdog time : %u ms, passed ", time);
+ /* 3.3.2. Set scratch register 1 to 0x0000xxxx */
+ watchdog_magic_write(0);
+ return 0;
+ } else {
+ /*test minimum watchdogtime */
+ post_log("hw watchdog time : %u ms, failed ", time);
+ return 2;
+ }
}
return -1;
}
projects / karo-tx-uboot.git / commitdiff