## ARM926EJ-S Systems
#########################################################################
-at91sam9261ek_nandflash_config \
-at91sam9261ek_dataflash_cs0_config \
-at91sam9261ek_dataflash_cs3_config \
-at91sam9261ek_config \
-at91sam9g10ek_nandflash_config \
-at91sam9g10ek_dataflash_cs0_config \
-at91sam9g10ek_dataflash_cs3_config \
-at91sam9g10ek_config : unconfig
- @mkdir -p $(obj)include
- @if [ "$(findstring 9g10,$@)" ] ; then \
- echo "#define CONFIG_AT91SAM9G10EK 1" >>$(obj)include/config.h ; \
- else \
- echo "#define CONFIG_AT91SAM9261EK 1" >>$(obj)include/config.h ; \
- fi;
- @if [ "$(findstring _nandflash,$@)" ] ; then \
- echo "#define CONFIG_SYS_USE_NANDFLASH 1" >>$(obj)include/config.h ; \
- elif [ "$(findstring dataflash_cs0,$@)" ] ; then \
- echo "#define CONFIG_SYS_USE_DATAFLASH_CS3 1" >>$(obj)include/config.h ; \
- else \
- echo "#define CONFIG_SYS_USE_DATAFLASH_CS0 1" >>$(obj)include/config.h ; \
- fi;
- @$(MKCONFIG) -n $@ -a at91sam9261ek arm arm926ejs at91sam9261ek atmel at91
-
at91sam9263ek_norflash_config \
at91sam9263ek_norflash_boot_config \
at91sam9263ek_nandflash_config \
*/
#include <common.h>
+#include <asm/io.h>
#include <asm/arch/at91sam9261.h>
#include <asm/arch/at91sam9261_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
#include <lcd.h>
#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
#ifdef CONFIG_CMD_NAND
static void at91sam9261ek_nand_hw_init(void)
{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
unsigned long csa;
/* Enable CS3 */
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA,
- csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+
+ writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
#ifdef CONFIG_AT91SAM9G10EK
- at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3),
- AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(7) |
- AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(7));
- at91_sys_write(AT91_SMC_CYCLE(3),
- AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+ writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
+ &smc->cs[3].cycle);
#else
- at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3),
- AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
- AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
- at91_sys_write(AT91_SMC_CYCLE(3),
- AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+ &smc->cs[3].cycle);
#endif
- at91_sys_write(AT91_SMC_MODE(3),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
- AT91_SMC_DBW_16 |
+ AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
- AT91_SMC_DBW_8 |
+ AT91_SMC_MODE_DBW_8 |
#endif
- AT91_SMC_TDF_(2));
+ AT91_SMC_MODE_TDF_CYCLE(2),
+ &smc->cs[3].mode);
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOC);
+ writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
#ifdef CONFIG_DRIVER_DM9000
static void at91sam9261ek_dm9000_hw_init(void)
{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
/* Configure SMC CS2 for DM9000 */
#ifdef CONFIG_AT91SAM9G10EK
- at91_sys_write(AT91_SMC_SETUP(2),
- AT91_SMC_NWESETUP_(3) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(3) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(2),
- AT91_SMC_NWEPULSE_(6) | AT91_SMC_NCS_WRPULSE_(8) |
- AT91_SMC_NRDPULSE_(6) | AT91_SMC_NCS_RDPULSE_(8));
- at91_sys_write(AT91_SMC_CYCLE(2),
- AT91_SMC_NWECYCLE_(20) | AT91_SMC_NRDCYCLE_(20));
- at91_sys_write(AT91_SMC_MODE(2),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
- AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 |
- AT91_SMC_TDF_(1));
+ writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[2].setup);
+ writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
+ AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
+ &smc->cs[2].pulse);
+ writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
+ &smc->cs[2].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
+ AT91_SMC_MODE_TDF_CYCLE(1),
+ &smc->cs[2].mode);
#else
- at91_sys_write(AT91_SMC_SETUP(2),
- AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(2),
- AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) |
- AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
- at91_sys_write(AT91_SMC_CYCLE(2),
- AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
- at91_sys_write(AT91_SMC_MODE(2),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
- AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 |
- AT91_SMC_TDF_(1));
+ writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[2].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
+ AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
+ &smc->cs[2].pulse);
+ writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
+ &smc->cs[2].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
+ AT91_SMC_MODE_TDF_CYCLE(1),
+ &smc->cs[2].mode);
#endif
/* Configure Reset signal as output */
vl_vsync_len: 1,
vl_upper_margin:1,
vl_lower_margin:0,
- mmio: AT91SAM9261_LCDC_BASE,
+ mmio: ATMEL_BASE_LCDC,
};
void lcd_enable(void)
static void at91sam9261ek_lcd_hw_init(void)
{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */
at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */
at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */
at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */
at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */
- at91_sys_write(AT91_PMC_SCER, AT91_PMC_HCK1);
+ writel(AT91_PMC_HCK1, &pmc->scer);
-#ifdef CONFIG_AT91SAM9G10EK
- gd->fb_base = CONFIG_AT91SAM9G10_LCD_BASE;
-#else
- gd->fb_base = AT91SAM9261_SRAM_BASE;
+ /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
+#ifdef CONFIG_AT91SAM9261EK
+ gd->fb_base = ATMEL_BASE_SRAM;
#endif
}
lcd_printf ("(C) 2008 ATMEL Corp\n");
lcd_printf ("at91support@atmel.com\n");
lcd_printf ("%s CPU at %s MHz\n",
- CONFIG_SYS_AT91_CPU_NAME,
+ ATMEL_CPU_NAME,
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
#endif
/* adress of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- at91_serial_hw_init();
+ at91_seriald_hw_init();
#ifdef CONFIG_CMD_NAND
at91sam9261ek_nand_hw_init();
#endif
int dram_init(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+
return 0;
}
+++ /dev/null
-CONFIG_SYS_TEXT_BASE = 0x23f00000
#include <asm/arch/at91sam9261.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/io.h>
void coloured_LED_init(void)
{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
/* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOA);
+ writel(ATMEL_ID_PIOA, &pmc->pcer);
at91_set_gpio_output(CONFIG_RED_LED, 1);
at91_set_gpio_output(CONFIG_GREEN_LED, 1);
at91sam9260ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH
at91sam9260ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS0
at91sam9260ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS1
+at91sam9261ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_NANDFLASH
+at91sam9261ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS0
+at91sam9261ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS3
+at91sam9g10ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH
+at91sam9g10ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0
+at91sam9g10ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3
at91sam9g20ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH
at91sam9g20ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0
at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_AT91_LEGACY
-
/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
-#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_HZ 1000
-#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
-#ifdef CONFIG_AT91SAM9G10EK
-#define CONFIG_AT91SAM9G10 1 /* It's an Atmel AT91SAM9G10 SoC*/
+#ifdef CONFIG_AT91SAM9G10
+#define CONFIG_AT91SAM9G10EK /* It's an Atmel AT91SAM9G10 EK*/
#else
-#define CONFIG_AT91SAM9261 1 /* It's an Atmel AT91SAM9261 SoC*/
+#define CONFIG_AT91SAM9261EK /* It's an Atmel AT91SAM9261 EK*/
#endif
+
+#include <asm/hardware.h>
+
#define CONFIG_ARCH_CPU_INIT
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_ATMEL_LEGACY
+#define CONFIG_SYS_TEXT_BASE 0x21f00000
+
/*
* Hardware drivers
*/
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_ATMEL_USART 1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3 1 /* USART 3 is DBGU */
+
+/* gpio */
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_GPIO_PULLUP 1
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200, 57600, 38400, 19200, 9600}
/* LCD */
-#define CONFIG_LCD 1
+#define CONFIG_LCD
#define LCD_BPP LCD_COLOR8
-#define CONFIG_LCD_LOGO 1
+#define CONFIG_LCD_LOGO
#undef LCD_TEST_PATTERN
-#define CONFIG_LCD_INFO 1
-#define CONFIG_LCD_INFO_BELOW_LOGO 1
-#define CONFIG_SYS_WHITE_ON_BLACK 1
-#define CONFIG_ATMEL_LCD 1
+#define CONFIG_LCD_INFO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_LCD
#ifdef CONFIG_AT91SAM9261EK
-#define CONFIG_ATMEL_LCD_BGR555 1
-#else
-#define CONFIG_AT91SAM9G10_LCD_BASE 0x23E00000 /* LCD is no more in SRAM */
+#define CONFIG_ATMEL_LCD_BGR555
#endif
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* LED */
#define CONFIG_AT91_LED
/*
* BOOTP options
*/
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_SOURCE
-#define CONFIG_CMD_PING 1
-#define CONFIG_CMD_DHCP 1
-#define CONFIG_CMD_NAND 1
-#define CONFIG_CMD_USB 1
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x20000000
-#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
+#define CONFIG_SYS_SDRAM_SIZE 0x04000000
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH 1
+#define CONFIG_HAS_DATAFLASH
#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
#define CONFIG_SYS_MAX_DATAFLASH_BANKS 2
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* CS3 */
-#define AT91_SPI_CLK 15000000
-#define DATAFLASH_TCSS (0x1a << 16)
-#define DATAFLASH_TCHS (0x1 << 24)
+#define AT91_SPI_CLK 15000000
+#define DATAFLASH_TCSS (0x1a << 16)
+#define DATAFLASH_TCHS (0x1 << 24)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_DBW_8 1
+#define CONFIG_SYS_NAND_DBW_8
/* our ALE is AD22 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 22)
/* our CLE is AD21 */
#endif
/* NOR flash - no real flash on this board */
-#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_SYS_NO_FLASH
/* Ethernet */
-#define CONFIG_NET_MULTI 1
-#define CONFIG_DRIVER_DM9000 1
+#define CONFIG_NET_MULTI
+#define CONFIG_DRIVER_DM9000
#define CONFIG_DM9000_BASE 0x30000000
#define DM9000_IO CONFIG_DM9000_BASE
#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
-#define CONFIG_DM9000_USE_16BIT 1
-#define CONFIG_DM9000_NO_SROM 1
+#define CONFIG_DM9000_USE_16BIT
+#define CONFIG_DM9000_NO_SROM
#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
+#define CONFIG_RESET_PHY_R
/* USB */
#define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9261_UHP_BASE */
#ifdef CONFIG_AT91SAM9G10EK
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g10"
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9261"
#endif
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-#define CONFIG_USB_STORAGE 1
-#define CONFIG_CMD_FAT 1
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
#ifdef CONFIG_SYS_USE_DATAFLASH_CS0
/* bootstrap + u-boot + env + linux in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH 1
+#define CONFIG_ENV_IS_IN_DATAFLASH
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
#define CONFIG_ENV_OFFSET 0x4200
#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
#elif CONFIG_SYS_USE_DATAFLASH_CS3
/* bootstrap + u-boot + env + linux in dataflash on CS3 */
-#define CONFIG_ENV_IS_IN_DATAFLASH 1
+#define CONFIG_ENV_IS_IN_DATAFLASH
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + 0x8400)
#define CONFIG_ENV_OFFSET 0x4200
#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + CONFIG_ENV_OFFSET)
#else /* CONFIG_SYS_USE_NANDFLASH */
/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x60000
#define CONFIG_ENV_OFFSET_REDUND 0x80000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#endif
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
-
#define CONFIG_SYS_PROMPT "U-Boot> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
-#define CONFIG_STACKSIZE (32*1024) /* regular stack */
+#define CONFIG_STACKSIZE (32*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
#error CONFIG_USE_IRQ not supported
projects / karo-tx-uboot.git / commitdiff