--- /dev/null
+/*
+ * Toshiba PCI Secure Digital Host Controller Interface driver
+ *
+ * Copyright (C) 2014 Ondrej Zary
+ * Copyright (C) 2007 Richard Betts, All Rights Reserved.
+ *
+ * Based on asic3_mmc.c, copyright (c) 2005 SDG Systems, LLC and,
+ * sdhci.c, copyright (C) 2005-2006 Pierre Ossman
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/scatterlist.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+
+#include "toshsd.h"
+
+#define DRIVER_NAME "toshsd"
+
+static const struct pci_device_id pci_ids[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA, 0x0805) },
+ { /* end: all zeroes */ },
+};
+
+MODULE_DEVICE_TABLE(pci, pci_ids);
+
+static void toshsd_init(struct toshsd_host *host)
+{
+ /* enable clock */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP,
+ SD_PCICFG_CLKSTOP_ENABLE_ALL);
+ pci_write_config_byte(host->pdev, SD_PCICFG_CARDDETECT, 2);
+
+ /* reset */
+ iowrite16(0, host->ioaddr + SD_SOFTWARERESET); /* assert */
+ mdelay(2);
+ iowrite16(1, host->ioaddr + SD_SOFTWARERESET); /* deassert */
+ mdelay(2);
+
+ /* Clear card registers */
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+ iowrite32(0, host->ioaddr + SD_CARDSTATUS);
+ iowrite32(0, host->ioaddr + SD_ERRORSTATUS0);
+ iowrite16(0, host->ioaddr + SD_STOPINTERNAL);
+
+ /* SDIO clock? */
+ iowrite16(0x100, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL);
+
+ /* enable LED */
+ pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE1,
+ SD_PCICFG_LED_ENABLE1_START);
+ pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE2,
+ SD_PCICFG_LED_ENABLE2_START);
+
+ /* set interrupt masks */
+ iowrite32(~(u32)(SD_CARD_RESP_END | SD_CARD_RW_END
+ | SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0
+ | SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE
+ | SD_BUF_CMD_TIMEOUT),
+ host->ioaddr + SD_INTMASKCARD);
+
+ iowrite16(0x1000, host->ioaddr + SD_TRANSACTIONCTRL);
+}
+
+/* Set MMC clock / power.
+ * Note: This controller uses a simple divider scheme therefore it cannot run
+ * SD/MMC cards at full speed (24/20MHz). HCLK (=33MHz PCI clock?) is too high
+ * and the next slowest is 16MHz (div=2).
+ */
+static void __toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ if (ios->clock) {
+ u16 clk;
+ int div = 1;
+
+ while (ios->clock < HCLK / div)
+ div *= 2;
+
+ clk = div >> 2;
+
+ if (div == 1) { /* disable the divider */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE,
+ SD_PCICFG_CLKMODE_DIV_DISABLE);
+ clk |= SD_CARDCLK_DIV_DISABLE;
+ } else
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, 0);
+
+ clk |= SD_CARDCLK_ENABLE_CLOCK;
+ iowrite16(clk, host->ioaddr + SD_CARDCLOCKCTRL);
+
+ mdelay(10);
+ } else
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+
+ switch (ios->power_mode) {
+ case MMC_POWER_OFF:
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1,
+ SD_PCICFG_PWR1_OFF);
+ mdelay(1);
+ break;
+ case MMC_POWER_UP:
+ break;
+ case MMC_POWER_ON:
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1,
+ SD_PCICFG_PWR1_33V);
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER2,
+ SD_PCICFG_PWR2_AUTO);
+ mdelay(20);
+ break;
+ }
+
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_1:
+ iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14)
+ | SD_CARDOPT_C2_MODULE_ABSENT
+ | SD_CARDOPT_DATA_XFR_WIDTH_1,
+ host->ioaddr + SD_CARDOPTIONSETUP);
+ break;
+ case MMC_BUS_WIDTH_4:
+ iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14)
+ | SD_CARDOPT_C2_MODULE_ABSENT
+ | SD_CARDOPT_DATA_XFR_WIDTH_4,
+ host->ioaddr + SD_CARDOPTIONSETUP);
+ break;
+ }
+}
+
+static void toshsd_set_led(struct toshsd_host *host, unsigned char state)
+{
+ iowrite16(state, host->ioaddr + SDIO_BASE + SDIO_LEDCTRL);
+}
+
+static void toshsd_finish_request(struct toshsd_host *host)
+{
+ struct mmc_request *mrq = host->mrq;
+
+ /* Write something to end the command */
+ host->mrq = NULL;
+ host->cmd = NULL;
+ host->data = NULL;
+
+ toshsd_set_led(host, 0);
+ mmc_request_done(host->mmc, mrq);
+}
+
+static irqreturn_t toshsd_thread_irq(int irq, void *dev_id)
+{
+ struct toshsd_host *host = dev_id;
+ struct mmc_data *data = host->data;
+ struct sg_mapping_iter *sg_miter = &host->sg_miter;
+ unsigned short *buf;
+ int count;
+ unsigned long flags;
+
+ if (!data) {
+ dev_warn(&host->pdev->dev, "Spurious Data IRQ\n");
+ if (host->cmd) {
+ host->cmd->error = -EIO;
+ toshsd_finish_request(host);
+ }
+ return IRQ_NONE;
+ }
+ spin_lock_irqsave(&host->lock, flags);
+
+ if (!sg_miter_next(sg_miter))
+ return IRQ_HANDLED;
+ buf = sg_miter->addr;
+
+ /* Ensure we dont read more than one block. The chip will interrupt us
+ * When the next block is available.
+ */
+ count = sg_miter->length;
+ if (count > data->blksz)
+ count = data->blksz;
+
+ dev_dbg(&host->pdev->dev, "count: %08x, flags %08x\n", count,
+ data->flags);
+
+ /* Transfer the data */
+ if (data->flags & MMC_DATA_READ)
+ ioread32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2);
+ else
+ iowrite32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2);
+
+ sg_miter->consumed = count;
+ sg_miter_stop(sg_miter);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static void toshsd_cmd_irq(struct toshsd_host *host)
+{
+ struct mmc_command *cmd = host->cmd;
+ u8 *buf = (u8 *) cmd->resp;
+ u16 data;
+
+ if (!host->cmd) {
+ dev_warn(&host->pdev->dev, "Spurious CMD irq\n");
+ return;
+ }
+
+ host->cmd = NULL;
+
+ if (cmd->flags & MMC_RSP_PRESENT && cmd->flags & MMC_RSP_136) {
+ /* R2 */
+ buf[12] = 0xff;
+ data = ioread16(host->ioaddr + SD_RESPONSE0);
+ buf[13] = data & 0xff;
+ buf[14] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE1);
+ buf[15] = data & 0xff;
+ buf[8] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE2);
+ buf[9] = data & 0xff;
+ buf[10] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE3);
+ buf[11] = data & 0xff;
+ buf[4] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE4);
+ buf[5] = data & 0xff;
+ buf[6] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE5);
+ buf[7] = data & 0xff;
+ buf[0] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE6);
+ buf[1] = data & 0xff;
+ buf[2] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE7);
+ buf[3] = data & 0xff;
+ } else if (cmd->flags & MMC_RSP_PRESENT) {
+ /* R1, R1B, R3, R6, R7 */
+ data = ioread16(host->ioaddr + SD_RESPONSE0);
+ buf[0] = data & 0xff;
+ buf[1] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE1);
+ buf[2] = data & 0xff;
+ buf[3] = data >> 8;
+ }
+
+ dev_dbg(&host->pdev->dev, "Command IRQ complete %d %d %x\n",
+ cmd->opcode, cmd->error, cmd->flags);
+
+ /* If there is data to handle we will
+ * finish the request in the mmc_data_end_irq handler.*/
+ if (host->data)
+ return;
+
+ toshsd_finish_request(host);
+}
+
+static void toshsd_data_end_irq(struct toshsd_host *host)
+{
+ struct mmc_data *data = host->data;
+
+ host->data = NULL;
+
+ if (!data) {
+ dev_warn(&host->pdev->dev, "Spurious data end IRQ\n");
+ return;
+ }
+
+ if (data->error == 0)
+ data->bytes_xfered = data->blocks * data->blksz;
+ else
+ data->bytes_xfered = 0;
+
+ dev_dbg(&host->pdev->dev, "Completed data request xfr=%d\n",
+ data->bytes_xfered);
+
+ iowrite16(0, host->ioaddr + SD_STOPINTERNAL);
+
+ toshsd_finish_request(host);
+}
+
+static irqreturn_t toshsd_irq(int irq, void *dev_id)
+{
+ struct toshsd_host *host = dev_id;
+ u32 int_reg, int_mask, int_status, detail;
+ int error = 0, ret = IRQ_HANDLED;
+
+ spin_lock(&host->lock);
+ int_status = ioread32(host->ioaddr + SD_CARDSTATUS);
+ int_mask = ioread32(host->ioaddr + SD_INTMASKCARD);
+ int_reg = int_status & ~int_mask & ~IRQ_DONT_CARE_BITS;
+
+ dev_dbg(&host->pdev->dev, "IRQ status:%x mask:%x\n",
+ int_status, int_mask);
+
+ /* nothing to do: it's not our IRQ */
+ if (!int_reg) {
+ ret = IRQ_NONE;
+ goto irq_end;
+ }
+
+ if (int_reg & SD_BUF_CMD_TIMEOUT) {
+ error = -ETIMEDOUT;
+ dev_dbg(&host->pdev->dev, "Timeout\n");
+ } else if (int_reg & SD_BUF_CRC_ERR) {
+ error = -EILSEQ;
+ dev_err(&host->pdev->dev, "BadCRC\n");
+ } else if (int_reg & (SD_BUF_ILLEGAL_ACCESS
+ | SD_BUF_CMD_INDEX_ERR
+ | SD_BUF_STOP_BIT_END_ERR
+ | SD_BUF_OVERFLOW
+ | SD_BUF_UNDERFLOW
+ | SD_BUF_DATA_TIMEOUT)) {
+ dev_err(&host->pdev->dev, "Buffer status error: { %s%s%s%s%s%s}\n",
+ int_reg & SD_BUF_ILLEGAL_ACCESS ? "ILLEGAL_ACC " : "",
+ int_reg & SD_BUF_CMD_INDEX_ERR ? "CMD_INDEX " : "",
+ int_reg & SD_BUF_STOP_BIT_END_ERR ? "STOPBIT_END " : "",
+ int_reg & SD_BUF_OVERFLOW ? "OVERFLOW " : "",
+ int_reg & SD_BUF_UNDERFLOW ? "UNDERFLOW " : "",
+ int_reg & SD_BUF_DATA_TIMEOUT ? "DATA_TIMEOUT " : "");
+
+ detail = ioread32(host->ioaddr + SD_ERRORSTATUS0);
+ dev_err(&host->pdev->dev, "detail error status { %s%s%s%s%s%s%s%s%s%s%s%s%s}\n",
+ detail & SD_ERR0_RESP_CMD_ERR ? "RESP_CMD " : "",
+ detail & SD_ERR0_RESP_NON_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "",
+ detail & SD_ERR0_RESP_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "",
+ detail & SD_ERR0_READ_DATA_END_BIT_ERR ? "READ_DATA_END_BIT " : "",
+ detail & SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR ? "WRITE_CMD_END_BIT " : "",
+ detail & SD_ERR0_RESP_NON_CMD12_CRC_ERR ? "RESP_CRC " : "",
+ detail & SD_ERR0_RESP_CMD12_CRC_ERR ? "RESP_CRC " : "",
+ detail & SD_ERR0_READ_DATA_CRC_ERR ? "READ_DATA_CRC " : "",
+ detail & SD_ERR0_WRITE_CMD_CRC_ERR ? "WRITE_CMD_CRC " : "",
+ detail & SD_ERR1_NO_CMD_RESP ? "NO_CMD_RESP " : "",
+ detail & SD_ERR1_TIMEOUT_READ_DATA ? "READ_DATA_TIMEOUT " : "",
+ detail & SD_ERR1_TIMEOUT_CRS_STATUS ? "CRS_STATUS_TIMEOUT " : "",
+ detail & SD_ERR1_TIMEOUT_CRC_BUSY ? "CRC_BUSY_TIMEOUT " : "");
+ error = -EIO;
+ }
+
+ if (error) {
+ if (host->cmd)
+ host->cmd->error = error;
+
+ if (error == -ETIMEDOUT) {
+ iowrite32(int_status &
+ ~(SD_BUF_CMD_TIMEOUT | SD_CARD_RESP_END),
+ host->ioaddr + SD_CARDSTATUS);
+ } else {
+ toshsd_init(host);
+ __toshsd_set_ios(host->mmc, &host->mmc->ios);
+ goto irq_end;
+ }
+ }
+
+ /* Card insert/remove. The mmc controlling code is stateless. */
+ if (int_reg & (SD_CARD_CARD_INSERTED_0 | SD_CARD_CARD_REMOVED_0)) {
+ iowrite32(int_status &
+ ~(SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0),
+ host->ioaddr + SD_CARDSTATUS);
+
+ if (int_reg & SD_CARD_CARD_INSERTED_0)
+ toshsd_init(host);
+
+ mmc_detect_change(host->mmc, 1);
+ }
+
+ /* Data transfer */
+ if (int_reg & (SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE)) {
+ iowrite32(int_status &
+ ~(SD_BUF_WRITE_ENABLE | SD_BUF_READ_ENABLE),
+ host->ioaddr + SD_CARDSTATUS);
+
+ ret = IRQ_WAKE_THREAD;
+ goto irq_end;
+ }
+
+ /* Command completion */
+ if (int_reg & SD_CARD_RESP_END) {
+ iowrite32(int_status & ~(SD_CARD_RESP_END),
+ host->ioaddr + SD_CARDSTATUS);
+ toshsd_cmd_irq(host);
+ }
+
+ /* Data transfer completion */
+ if (int_reg & SD_CARD_RW_END) {
+ iowrite32(int_status & ~(SD_CARD_RW_END),
+ host->ioaddr + SD_CARDSTATUS);
+ toshsd_data_end_irq(host);
+ }
+irq_end:
+ spin_unlock(&host->lock);
+ return ret;
+}
+
+static void toshsd_start_cmd(struct toshsd_host *host, struct mmc_command *cmd)
+{
+ struct mmc_data *data = host->data;
+ int c = cmd->opcode;
+
+ dev_dbg(&host->pdev->dev, "Command opcode: %d\n", cmd->opcode);
+
+ if (cmd->opcode == MMC_STOP_TRANSMISSION) {
+ iowrite16(SD_STOPINT_ISSUE_CMD12,
+ host->ioaddr + SD_STOPINTERNAL);
+
+ cmd->resp[0] = cmd->opcode;
+ cmd->resp[1] = 0;
+ cmd->resp[2] = 0;
+ cmd->resp[3] = 0;
+
+ toshsd_finish_request(host);
+ return;
+ }
+
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_NONE:
+ c |= SD_CMD_RESP_TYPE_NONE;
+ break;
+
+ case MMC_RSP_R1:
+ c |= SD_CMD_RESP_TYPE_EXT_R1;
+ break;
+ case MMC_RSP_R1B:
+ c |= SD_CMD_RESP_TYPE_EXT_R1B;
+ break;
+ case MMC_RSP_R2:
+ c |= SD_CMD_RESP_TYPE_EXT_R2;
+ break;
+ case MMC_RSP_R3:
+ c |= SD_CMD_RESP_TYPE_EXT_R3;
+ break;
+
+ default:
+ dev_err(&host->pdev->dev, "Unknown response type %d\n",
+ mmc_resp_type(cmd));
+ break;
+ }
+
+ host->cmd = cmd;
+
+ if (cmd->opcode == MMC_APP_CMD)
+ c |= SD_CMD_TYPE_ACMD;
+
+ if (cmd->opcode == MMC_GO_IDLE_STATE)
+ c |= (3 << 8); /* removed from ipaq-asic3.h for some reason */
+
+ if (data) {
+ c |= SD_CMD_DATA_PRESENT;
+
+ if (data->blocks > 1) {
+ iowrite16(SD_STOPINT_AUTO_ISSUE_CMD12,
+ host->ioaddr + SD_STOPINTERNAL);
+ c |= SD_CMD_MULTI_BLOCK;
+ }
+
+ if (data->flags & MMC_DATA_READ)
+ c |= SD_CMD_TRANSFER_READ;
+
+ /* MMC_DATA_WRITE does not require a bit to be set */
+ }
+
+ /* Send the command */
+ iowrite32(cmd->arg, host->ioaddr + SD_ARG0);
+ iowrite16(c, host->ioaddr + SD_CMD);
+}
+
+static void toshsd_start_data(struct toshsd_host *host, struct mmc_data *data)
+{
+ unsigned int flags = SG_MITER_ATOMIC;
+
+ dev_dbg(&host->pdev->dev, "setup data transfer: blocksize %08x nr_blocks %d, offset: %08x\n",
+ data->blksz, data->blocks, data->sg->offset);
+
+ host->data = data;
+
+ if (data->flags & MMC_DATA_READ)
+ flags |= SG_MITER_TO_SG;
+ else
+ flags |= SG_MITER_FROM_SG;
+
+ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
+
+ /* Set transfer length and blocksize */
+ iowrite16(data->blocks, host->ioaddr + SD_BLOCKCOUNT);
+ iowrite16(data->blksz, host->ioaddr + SD_CARDXFERDATALEN);
+}
+
+/* Process requests from the MMC layer */
+static void toshsd_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ /* abort if card not present */
+ if (!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0)) {
+ mrq->cmd->error = -ENOMEDIUM;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ WARN_ON(host->mrq != NULL);
+
+ host->mrq = mrq;
+
+ if (mrq->data)
+ toshsd_start_data(host, mrq->data);
+
+ toshsd_set_led(host, 1);
+
+ toshsd_start_cmd(host, mrq->cmd);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static void toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ __toshsd_set_ios(mmc, ios);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static int toshsd_get_ro(struct mmc_host *mmc)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ /* active low */
+ return !(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_WRITE_PROTECT);
+}
+
+static int toshsd_get_cd(struct mmc_host *mmc)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ return !!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0);
+}
+
+static struct mmc_host_ops toshsd_ops = {
+ .request = toshsd_request,
+ .set_ios = toshsd_set_ios,
+ .get_ro = toshsd_get_ro,
+ .get_cd = toshsd_get_cd,
+};
+
+
+static void toshsd_powerdown(struct toshsd_host *host)
+{
+ /* mask all interrupts */
+ iowrite32(0xffffffff, host->ioaddr + SD_INTMASKCARD);
+ /* disable card clock */
+ iowrite16(0x000, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL);
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+ /* power down card */
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, SD_PCICFG_PWR1_OFF);
+ /* disable clock */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, 0);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int toshsd_pm_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+
+ toshsd_powerdown(host);
+
+ pci_save_state(pdev);
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+ return 0;
+}
+
+static int toshsd_pm_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+ int ret;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ toshsd_init(host);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static int toshsd_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ int ret;
+ struct toshsd_host *host;
+ struct mmc_host *mmc;
+ resource_size_t base;
+
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ mmc = mmc_alloc_host(sizeof(struct toshsd_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+
+ host->pdev = pdev;
+ pci_set_drvdata(pdev, host);
+
+ ret = pci_request_regions(pdev, DRIVER_NAME);
+ if (ret)
+ goto free;
+
+ host->ioaddr = pci_iomap(pdev, 0, 0);
+ if (!host->ioaddr) {
+ ret = -ENOMEM;
+ goto release;
+ }
+
+ /* Set MMC host parameters */
+ mmc->ops = &toshsd_ops;
+ mmc->caps = MMC_CAP_4_BIT_DATA;
+ mmc->ocr_avail = MMC_VDD_32_33;
+
+ mmc->f_min = HCLK / 512;
+ mmc->f_max = HCLK;
+
+ spin_lock_init(&host->lock);
+
+ toshsd_init(host);
+
+ ret = request_threaded_irq(pdev->irq, toshsd_irq, toshsd_thread_irq,
+ IRQF_SHARED, DRIVER_NAME, host);
+ if (ret)
+ goto unmap;
+
+ mmc_add_host(mmc);
+
+ base = pci_resource_start(pdev, 0);
+ dev_dbg(&pdev->dev, "MMIO %pa, IRQ %d\n", &base, pdev->irq);
+
+ pm_suspend_ignore_children(&pdev->dev, 1);
+
+ return 0;
+
+unmap:
+ pci_iounmap(pdev, host->ioaddr);
+release:
+ pci_release_regions(pdev);
+free:
+ mmc_free_host(mmc);
+ pci_set_drvdata(pdev, NULL);
+err:
+ pci_disable_device(pdev);
+ return ret;
+}
+
+static void toshsd_remove(struct pci_dev *pdev)
+{
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+
+ mmc_remove_host(host->mmc);
+ toshsd_powerdown(host);
+ free_irq(pdev->irq, host);
+ pci_iounmap(pdev, host->ioaddr);
+ pci_release_regions(pdev);
+ mmc_free_host(host->mmc);
+ pci_set_drvdata(pdev, NULL);
+ pci_disable_device(pdev);
+}
+
+static const struct dev_pm_ops toshsd_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(toshsd_pm_suspend, toshsd_pm_resume)
+};
+
+static struct pci_driver toshsd_driver = {
+ .name = DRIVER_NAME,
+ .id_table = pci_ids,
+ .probe = toshsd_probe,
+ .remove = toshsd_remove,
+ .driver.pm = &toshsd_pm_ops,
+};
+
+static int __init toshsd_drv_init(void)
+{
+ return pci_register_driver(&toshsd_driver);
+}
+
+static void __exit toshsd_drv_exit(void)
+{
+ pci_unregister_driver(&toshsd_driver);
+}
+
+module_init(toshsd_drv_init);
+module_exit(toshsd_drv_exit);
+
+MODULE_AUTHOR("Ondrej Zary, Richard Betts");
+MODULE_DESCRIPTION("Toshiba PCI Secure Digital Host Controller Interface driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Toshiba PCI Secure Digital Host Controller Interface driver
+ *
+ * Copyright (C) 2014 Ondrej Zary
+ * Copyright (C) 2007 Richard Betts, All Rights Reserved.
+ *
+ * Based on asic3_mmc.c Copyright (c) 2005 SDG Systems, LLC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#define HCLK 33000000 /* 33 MHz (PCI clock) */
+
+#define SD_PCICFG_CLKSTOP 0x40 /* 0x1f = clock controller, 0 = stop */
+#define SD_PCICFG_GATEDCLK 0x41 /* Gated clock */
+#define SD_PCICFG_CLKMODE 0x42 /* Control clock of SD controller */
+#define SD_PCICFG_PINSTATUS 0x44 /* R/O: read status of SD pins */
+#define SD_PCICFG_POWER1 0x48
+#define SD_PCICFG_POWER2 0x49
+#define SD_PCICFG_POWER3 0x4a
+#define SD_PCICFG_CARDDETECT 0x4c
+#define SD_PCICFG_SLOTS 0x50 /* R/O: define support slot number */
+#define SD_PCICFG_EXTGATECLK1 0xf0 /* Could be used for gated clock */
+#define SD_PCICFG_EXTGATECLK2 0xf1 /* Could be used for gated clock */
+#define SD_PCICFG_EXTGATECLK3 0xf9 /* Bit 1: double buffer/single buffer */
+#define SD_PCICFG_SDLED_ENABLE1 0xfa
+#define SD_PCICFG_SDLED_ENABLE2 0xfe
+
+#define SD_PCICFG_CLKMODE_DIV_DISABLE BIT(0)
+#define SD_PCICFG_CLKSTOP_ENABLE_ALL 0x1f
+#define SD_PCICFG_LED_ENABLE1_START 0x12
+#define SD_PCICFG_LED_ENABLE2_START 0x80
+
+#define SD_PCICFG_PWR1_33V 0x08 /* Set for 3.3 volts */
+#define SD_PCICFG_PWR1_OFF 0x00 /* Turn off power */
+#define SD_PCICFG_PWR2_AUTO 0x02
+
+#define SD_CMD 0x00 /* also for SDIO */
+#define SD_ARG0 0x04 /* also for SDIO */
+#define SD_ARG1 0x06 /* also for SDIO */
+#define SD_STOPINTERNAL 0x08
+#define SD_BLOCKCOUNT 0x0a /* also for SDIO */
+#define SD_RESPONSE0 0x0c /* also for SDIO */
+#define SD_RESPONSE1 0x0e /* also for SDIO */
+#define SD_RESPONSE2 0x10 /* also for SDIO */
+#define SD_RESPONSE3 0x12 /* also for SDIO */
+#define SD_RESPONSE4 0x14 /* also for SDIO */
+#define SD_RESPONSE5 0x16 /* also for SDIO */
+#define SD_RESPONSE6 0x18 /* also for SDIO */
+#define SD_RESPONSE7 0x1a /* also for SDIO */
+#define SD_CARDSTATUS 0x1c /* also for SDIO */
+#define SD_BUFFERCTRL 0x1e /* also for SDIO */
+#define SD_INTMASKCARD 0x20 /* also for SDIO */
+#define SD_INTMASKBUFFER 0x22 /* also for SDIO */
+#define SD_CARDCLOCKCTRL 0x24
+#define SD_CARDXFERDATALEN 0x26 /* also for SDIO */
+#define SD_CARDOPTIONSETUP 0x28 /* also for SDIO */
+#define SD_ERRORSTATUS0 0x2c /* also for SDIO */
+#define SD_ERRORSTATUS1 0x2e /* also for SDIO */
+#define SD_DATAPORT 0x30 /* also for SDIO */
+#define SD_TRANSACTIONCTRL 0x34 /* also for SDIO */
+#define SD_SOFTWARERESET 0xe0 /* also for SDIO */
+
+/* registers above marked "also for SDIO" and all SDIO registers below can be
+ * accessed at SDIO_BASE + reg address */
+#define SDIO_BASE 0x100
+
+#define SDIO_CARDPORTSEL 0x02
+#define SDIO_CARDINTCTRL 0x36
+#define SDIO_CLOCKNWAITCTRL 0x38
+#define SDIO_HOSTINFORMATION 0x3a
+#define SDIO_ERRORCTRL 0x3c
+#define SDIO_LEDCTRL 0x3e
+
+#define SD_TRANSCTL_SET BIT(8)
+
+#define SD_CARDCLK_DIV_DISABLE BIT(15)
+#define SD_CARDCLK_ENABLE_CLOCK BIT(8)
+#define SD_CARDCLK_CLK_DIV_512 BIT(7)
+#define SD_CARDCLK_CLK_DIV_256 BIT(6)
+#define SD_CARDCLK_CLK_DIV_128 BIT(5)
+#define SD_CARDCLK_CLK_DIV_64 BIT(4)
+#define SD_CARDCLK_CLK_DIV_32 BIT(3)
+#define SD_CARDCLK_CLK_DIV_16 BIT(2)
+#define SD_CARDCLK_CLK_DIV_8 BIT(1)
+#define SD_CARDCLK_CLK_DIV_4 BIT(0)
+#define SD_CARDCLK_CLK_DIV_2 0
+
+#define SD_CARDOPT_REQUIRED 0x000e
+#define SD_CARDOPT_DATA_RESP_TIMEOUT(x) (((x) & 0x0f) << 4) /* 4 bits */
+#define SD_CARDOPT_C2_MODULE_ABSENT BIT(14)
+#define SD_CARDOPT_DATA_XFR_WIDTH_1 (1 << 15)
+#define SD_CARDOPT_DATA_XFR_WIDTH_4 (0 << 15)
+
+#define SD_CMD_TYPE_CMD (0 << 6)
+#define SD_CMD_TYPE_ACMD (1 << 6)
+#define SD_CMD_TYPE_AUTHEN (2 << 6)
+#define SD_CMD_RESP_TYPE_NONE (3 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R1 (4 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R1B (5 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R2 (6 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R3 (7 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R6 (4 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R7 (4 << 8)
+#define SD_CMD_DATA_PRESENT BIT(11)
+#define SD_CMD_TRANSFER_READ BIT(12)
+#define SD_CMD_MULTI_BLOCK BIT(13)
+#define SD_CMD_SECURITY_CMD BIT(14)
+
+#define SD_STOPINT_ISSUE_CMD12 BIT(0)
+#define SD_STOPINT_AUTO_ISSUE_CMD12 BIT(8)
+
+#define SD_CARD_RESP_END BIT(0)
+#define SD_CARD_RW_END BIT(2)
+#define SD_CARD_CARD_REMOVED_0 BIT(3)
+#define SD_CARD_CARD_INSERTED_0 BIT(4)
+#define SD_CARD_PRESENT_0 BIT(5)
+#define SD_CARD_UNK6 BIT(6)
+#define SD_CARD_WRITE_PROTECT BIT(7)
+#define SD_CARD_CARD_REMOVED_3 BIT(8)
+#define SD_CARD_CARD_INSERTED_3 BIT(9)
+#define SD_CARD_PRESENT_3 BIT(10)
+
+#define SD_BUF_CMD_INDEX_ERR BIT(16)
+#define SD_BUF_CRC_ERR BIT(17)
+#define SD_BUF_STOP_BIT_END_ERR BIT(18)
+#define SD_BUF_DATA_TIMEOUT BIT(19)
+#define SD_BUF_OVERFLOW BIT(20)
+#define SD_BUF_UNDERFLOW BIT(21)
+#define SD_BUF_CMD_TIMEOUT BIT(22)
+#define SD_BUF_UNK7 BIT(23)
+#define SD_BUF_READ_ENABLE BIT(24)
+#define SD_BUF_WRITE_ENABLE BIT(25)
+#define SD_BUF_ILLEGAL_FUNCTION BIT(29)
+#define SD_BUF_CMD_BUSY BIT(30)
+#define SD_BUF_ILLEGAL_ACCESS BIT(31)
+
+#define SD_ERR0_RESP_CMD_ERR BIT(0)
+#define SD_ERR0_RESP_NON_CMD12_END_BIT_ERR BIT(2)
+#define SD_ERR0_RESP_CMD12_END_BIT_ERR BIT(3)
+#define SD_ERR0_READ_DATA_END_BIT_ERR BIT(4)
+#define SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR BIT(5)
+#define SD_ERR0_RESP_NON_CMD12_CRC_ERR BIT(8)
+#define SD_ERR0_RESP_CMD12_CRC_ERR BIT(9)
+#define SD_ERR0_READ_DATA_CRC_ERR BIT(10)
+#define SD_ERR0_WRITE_CMD_CRC_ERR BIT(11)
+
+#define SD_ERR1_NO_CMD_RESP BIT(16)
+#define SD_ERR1_TIMEOUT_READ_DATA BIT(20)
+#define SD_ERR1_TIMEOUT_CRS_STATUS BIT(21)
+#define SD_ERR1_TIMEOUT_CRC_BUSY BIT(22)
+
+#define IRQ_DONT_CARE_BITS (SD_CARD_PRESENT_3 \
+ | SD_CARD_WRITE_PROTECT \
+ | SD_CARD_UNK6 \
+ | SD_CARD_PRESENT_0 \
+ | SD_BUF_UNK7 \
+ | SD_BUF_CMD_BUSY)
+
+struct toshsd_host {
+ struct pci_dev *pdev;
+ struct mmc_host *mmc;
+
+ spinlock_t lock;
+
+ struct mmc_request *mrq;/* Current request */
+ struct mmc_command *cmd;/* Current command */
+ struct mmc_data *data; /* Current data request */
+
+ struct sg_mapping_iter sg_miter; /* for PIO */
+
+ void __iomem *ioaddr; /* mapped address */
+};
projects / karo-tx-linux.git / commitdiff