}
/* Clear Bit 14 of AR_WA after putting chip into Full Sleep mode. */
- REG_WRITE(ah, AR_WA, ah->WARegVal & ~AR_WA_D3_L1_DISABLE);
+ if (AR_SREV_9300_20_OR_LATER(ah))
+ REG_WRITE(ah, AR_WA, ah->WARegVal & ~AR_WA_D3_L1_DISABLE);
}
/*
.chain_noise_scale = 1000,
.wd_timeout = IWL_DEF_WD_TIMEOUT,
.max_event_log_size = 128,
+ .wd_disable = true,
};
static struct iwl_ht_params iwl1000_ht_params = {
.ht_greenfield_support = true,
.wd_timeout = IWL_LONG_WD_TIMEOUT,
.max_event_log_size = 512,
.no_idle_support = true,
+ .wd_disable = true,
};
static struct iwl_ht_params iwl5000_ht_params = {
.ht_greenfield_support = true,
return 0;
}
+void iwlagn_config_ht40(struct ieee80211_conf *conf,
+ struct iwl_rxon_context *ctx)
+{
+ if (conf_is_ht40_minus(conf)) {
+ ctx->ht.extension_chan_offset =
+ IEEE80211_HT_PARAM_CHA_SEC_BELOW;
+ ctx->ht.is_40mhz = true;
+ } else if (conf_is_ht40_plus(conf)) {
+ ctx->ht.extension_chan_offset =
+ IEEE80211_HT_PARAM_CHA_SEC_ABOVE;
+ ctx->ht.is_40mhz = true;
+ } else {
+ ctx->ht.extension_chan_offset =
+ IEEE80211_HT_PARAM_CHA_SEC_NONE;
+ ctx->ht.is_40mhz = false;
+ }
+}
+
int iwlagn_mac_config(struct ieee80211_hw *hw, u32 changed)
{
struct iwl_priv *priv = hw->priv;
ctx->ht.enabled = conf_is_ht(conf);
if (ctx->ht.enabled) {
- if (conf_is_ht40_minus(conf)) {
- ctx->ht.extension_chan_offset =
- IEEE80211_HT_PARAM_CHA_SEC_BELOW;
- ctx->ht.is_40mhz = true;
- } else if (conf_is_ht40_plus(conf)) {
- ctx->ht.extension_chan_offset =
- IEEE80211_HT_PARAM_CHA_SEC_ABOVE;
- ctx->ht.is_40mhz = true;
- } else {
- ctx->ht.extension_chan_offset =
- IEEE80211_HT_PARAM_CHA_SEC_NONE;
- ctx->ht.is_40mhz = false;
- }
+ /* if HT40 is used, it should not change
+ * after associated except channel switch */
+ if (iwl_is_associated_ctx(ctx) &&
+ !ctx->ht.is_40mhz)
+ iwlagn_config_ht40(conf, ctx);
} else
ctx->ht.is_40mhz = false;
switch (keyconf->cipher) {
case WLAN_CIPHER_SUITE_TKIP:
- keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC;
- keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
-
if (sta)
addr = sta->addr;
else /* station mode case only */
seq.tkip.iv32, p1k, CMD_SYNC);
break;
case WLAN_CIPHER_SUITE_CCMP:
- keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
- /* fall through */
case WLAN_CIPHER_SUITE_WEP40:
case WLAN_CIPHER_SUITE_WEP104:
ret = iwlagn_send_sta_key(priv, keyconf, sta_id,
module_param_named(ack_check, iwlagn_mod_params.ack_check, bool, S_IRUGO);
MODULE_PARM_DESC(ack_check, "Check ack health (default: 0 [disabled])");
-module_param_named(wd_disable, iwlagn_mod_params.wd_disable, bool, S_IRUGO);
+module_param_named(wd_disable, iwlagn_mod_params.wd_disable, int, S_IRUGO);
MODULE_PARM_DESC(wd_disable,
- "Disable stuck queue watchdog timer (default: 0 [enabled])");
+ "Disable stuck queue watchdog timer 0=system default, "
+ "1=disable, 2=enable (default: 0)");
/*
* set bt_coex_active to true, uCode will do kill/defer
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
u32 changes);
+void iwlagn_config_ht40(struct ieee80211_conf *conf,
+ struct iwl_rxon_context *ctx);
/* uCode */
int iwlagn_rx_calib_result(struct iwl_priv *priv,
{
unsigned int timeout = priv->cfg->base_params->wd_timeout;
- if (timeout && !iwlagn_mod_params.wd_disable)
- mod_timer(&priv->watchdog,
- jiffies + msecs_to_jiffies(IWL_WD_TICK(timeout)));
- else
- del_timer(&priv->watchdog);
+ if (!iwlagn_mod_params.wd_disable) {
+ /* use system default */
+ if (timeout && !priv->cfg->base_params->wd_disable)
+ mod_timer(&priv->watchdog,
+ jiffies +
+ msecs_to_jiffies(IWL_WD_TICK(timeout)));
+ else
+ del_timer(&priv->watchdog);
+ } else {
+ /* module parameter overwrite default configuration */
+ if (timeout && iwlagn_mod_params.wd_disable == 2)
+ mod_timer(&priv->watchdog,
+ jiffies +
+ msecs_to_jiffies(IWL_WD_TICK(timeout)));
+ else
+ del_timer(&priv->watchdog);
+ }
}
/**
* @shadow_reg_enable: HW shadhow register bit
* @no_idle_support: do not support idle mode
* @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
+ * wd_disable: disable watchdog timer
*/
struct iwl_base_params {
int eeprom_size;
const bool shadow_reg_enable;
const bool no_idle_support;
const bool hd_v2;
+ const bool wd_disable;
};
/*
* @advanced_bt_coexist: support advanced bt coexist
* @restart_fw: restart firmware, default = 1
* @plcp_check: enable plcp health check, default = true
* @ack_check: disable ack health check, default = false
- * @wd_disable: enable stuck queue check, default = false
+ * @wd_disable: enable stuck queue check, default = 0
* @bt_coex_active: enable bt coex, default = true
* @led_mode: system default, default = 0
* @no_sleep_autoadjust: disable autoadjust, default = true
int restart_fw;
bool plcp_check;
bool ack_check;
- bool wd_disable;
+ int wd_disable;
bool bt_coex_active;
int led_mode;
bool no_sleep_autoadjust;
return 0;
}
-static void iwl_trans_pcie_disable_sync_irq(struct iwl_trans *trans)
+static void iwl_trans_pcie_stop_device(struct iwl_trans *trans)
{
unsigned long flags;
- struct iwl_trans_pcie *trans_pcie =
- IWL_TRANS_GET_PCIE_TRANS(trans);
+ struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+ /* tell the device to stop sending interrupts */
spin_lock_irqsave(&trans->shrd->lock, flags);
iwl_disable_interrupts(trans);
spin_unlock_irqrestore(&trans->shrd->lock, flags);
- /* wait to make sure we flush pending tasklet*/
- synchronize_irq(bus(trans)->irq);
- tasklet_kill(&trans_pcie->irq_tasklet);
-}
-
-static void iwl_trans_pcie_stop_device(struct iwl_trans *trans)
-{
- /* stop and reset the on-board processor */
- iwl_write32(bus(trans), CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET);
-
- /* tell the device to stop sending interrupts */
- iwl_trans_pcie_disable_sync_irq(trans);
-
/* device going down, Stop using ICT table */
iwl_disable_ict(trans);
/* Stop the device, and put it in low power state */
iwl_apm_stop(priv(trans));
+
+ /* Upon stop, the APM issues an interrupt if HW RF kill is set.
+ * Clean again the interrupt here
+ */
+ spin_lock_irqsave(&trans->shrd->lock, flags);
+ iwl_disable_interrupts(trans);
+ spin_unlock_irqrestore(&trans->shrd->lock, flags);
+
+ /* wait to make sure we flush pending tasklet*/
+ synchronize_irq(bus(trans)->irq);
+ tasklet_kill(&trans_pcie->irq_tasklet);
+
+ /* stop and reset the on-board processor */
+ iwl_write32(bus(trans), CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET);
}
static int iwl_trans_pcie_tx(struct iwl_trans *trans, struct sk_buff *skb,
if (channel &&
!(channel->flags & IEEE80211_CHAN_DISABLED)) {
bss = cfg80211_inform_bss(wiphy, channel,
- bssid, le64_to_cpu(*(__le64 *)tsfdesc),
+ bssid, get_unaligned_le64(tsfdesc),
capa, intvl, ie, ielen,
LBS_SCAN_RSSI_TO_MBM(rssi),
GFP_KERNEL);
spin_unlock_irqrestore(&card->buffer_lock, flags);
break;
default:
+ kfree(packet);
netdev_err(priv->dev, "can't transfer buffer of type %d\n",
type);
err = -EINVAL;
wildcard_ssid_tlv->header.len = cpu_to_le16(
(u16) (ssid_len + sizeof(wildcard_ssid_tlv->
max_ssid_length)));
- wildcard_ssid_tlv->max_ssid_length =
- user_scan_in->ssid_list[ssid_idx].max_len;
+
+ /* max_ssid_length = 0 tells firmware to perform
+ specific scan for the SSID filled */
+ wildcard_ssid_tlv->max_ssid_length = 0;
memcpy(wildcard_ssid_tlv->ssid,
user_scan_in->ssid_list[ssid_idx].ssid,
mutex_lock(&priv->mutex);
WARN_ON(priv->fw_state != FW_STATE_READY);
- cancel_work_sync(&priv->work);
-
p54spi_power_off(priv);
spin_lock_irqsave(&priv->tx_lock, flags);
INIT_LIST_HEAD(&priv->tx_pending);
priv->fw_state = FW_STATE_OFF;
mutex_unlock(&priv->mutex);
+
+ cancel_work_sync(&priv->work);
}
static int __devinit p54spi_probe(struct spi_device *spi)
init_completion(&priv->fw_comp);
INIT_LIST_HEAD(&priv->tx_pending);
mutex_init(&priv->mutex);
+ spin_lock_init(&priv->tx_lock);
SET_IEEE80211_DEV(hw, &spi->dev);
priv->common.open = p54spi_op_start;
priv->common.stop = p54spi_op_stop;
dwrq->flags = 0;
dwrq->length = 0;
}
- essid->octets[essid->length] = '\0';
+ essid->octets[dwrq->length] = '\0';
memcpy(extra, essid->octets, dwrq->length);
kfree(essid);
/* Apparently the data is read from end to start */
rt2800_register_read_lock(rt2x00dev, EFUSE_DATA3, ®);
/* The returned value is in CPU order, but eeprom is le */
- rt2x00dev->eeprom[i] = cpu_to_le32(reg);
+ *(u32 *)&rt2x00dev->eeprom[i] = cpu_to_le32(reg);
rt2800_register_read_lock(rt2x00dev, EFUSE_DATA2, ®);
*(u32 *)&rt2x00dev->eeprom[i + 2] = cpu_to_le32(reg);
rt2800_register_read_lock(rt2x00dev, EFUSE_DATA1, ®);
{ USB_DEVICE(0x050d, 0x935b) },
/* Buffalo */
{ USB_DEVICE(0x0411, 0x00e8) },
+ { USB_DEVICE(0x0411, 0x0158) },
{ USB_DEVICE(0x0411, 0x016f) },
{ USB_DEVICE(0x0411, 0x01a2) },
/* Corega */
* Powersaving work
*/
struct delayed_work autowakeup_work;
+ struct work_struct sleep_work;
/*
* Data queue arrays for RX, TX, Beacon and ATIM.
return NULL;
}
+static void rt2x00lib_sleep(struct work_struct *work)
+{
+ struct rt2x00_dev *rt2x00dev =
+ container_of(work, struct rt2x00_dev, sleep_work);
+
+ if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
+ return;
+
+ /*
+ * Check again is powersaving is enabled, to prevent races from delayed
+ * work execution.
+ */
+ if (!test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
+ rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf,
+ IEEE80211_CONF_CHANGE_PS);
+}
+
static void rt2x00lib_rxdone_check_ps(struct rt2x00_dev *rt2x00dev,
struct sk_buff *skb,
struct rxdone_entry_desc *rxdesc)
cam |= (tim_ie->bitmap_ctrl & 0x01);
if (!cam && !test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags))
- rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf,
- IEEE80211_CONF_CHANGE_PS);
+ queue_work(rt2x00dev->workqueue, &rt2x00dev->sleep_work);
}
static int rt2x00lib_rxdone_read_signal(struct rt2x00_dev *rt2x00dev,
INIT_WORK(&rt2x00dev->intf_work, rt2x00lib_intf_scheduled);
INIT_DELAYED_WORK(&rt2x00dev->autowakeup_work, rt2x00lib_autowakeup);
+ INIT_WORK(&rt2x00dev->sleep_work, rt2x00lib_sleep);
/*
* Let the driver probe the device to detect the capabilities.
*/
cancel_work_sync(&rt2x00dev->intf_work);
cancel_delayed_work_sync(&rt2x00dev->autowakeup_work);
+ cancel_work_sync(&rt2x00dev->sleep_work);
if (rt2x00_is_usb(rt2x00dev)) {
del_timer_sync(&rt2x00dev->txstatus_timer);
cancel_work_sync(&rt2x00dev->rxdone_work);
if (mac->link_state != MAC80211_LINKED)
return;
- spin_lock(&rtlpriv->locks.lps_lock);
+ spin_lock_irq(&rtlpriv->locks.lps_lock);
/* Idle for a while if we connect to AP a while ago. */
if (mac->cnt_after_linked >= 2) {
}
}
- spin_unlock(&rtlpriv->locks.lps_lock);
+ spin_unlock_irq(&rtlpriv->locks.lps_lock);
}
/*Leave the leisure power save mode.*/
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
+ unsigned long flags;
- spin_lock(&rtlpriv->locks.lps_lock);
+ spin_lock_irqsave(&rtlpriv->locks.lps_lock, flags);
if (ppsc->fwctrl_lps) {
if (ppsc->dot11_psmode != EACTIVE) {
rtl_lps_set_psmode(hw, EACTIVE);
}
}
- spin_unlock(&rtlpriv->locks.lps_lock);
+ spin_unlock_irqrestore(&rtlpriv->locks.lps_lock, flags);
}
/* For sw LPS*/
RT_CLEAR_PS_LEVEL(ppsc, RT_PS_LEVEL_ASPM);
}
- spin_lock(&rtlpriv->locks.lps_lock);
+ spin_lock_irq(&rtlpriv->locks.lps_lock);
rtl_ps_set_rf_state(hw, ERFON, RF_CHANGE_BY_PS);
- spin_unlock(&rtlpriv->locks.lps_lock);
+ spin_unlock_irq(&rtlpriv->locks.lps_lock);
}
void rtl_swlps_rfon_wq_callback(void *data)
if (rtlpriv->link_info.busytraffic)
return;
- spin_lock(&rtlpriv->locks.lps_lock);
+ spin_lock_irq(&rtlpriv->locks.lps_lock);
rtl_ps_set_rf_state(hw, ERFSLEEP, RF_CHANGE_BY_PS);
- spin_unlock(&rtlpriv->locks.lps_lock);
+ spin_unlock_irq(&rtlpriv->locks.lps_lock);
if (ppsc->reg_rfps_level & RT_RF_OFF_LEVL_ASPM &&
!RT_IN_PS_LEVEL(ppsc, RT_PS_LEVEL_ASPM)) {
return -ENOENT;
}
+ /* if we're already stopping ignore any new requests to stop */
+ if (test_bit(HT_AGG_STATE_STOPPING, &tid_tx->state)) {
+ spin_unlock_bh(&sta->lock);
+ return -EALREADY;
+ }
+
if (test_bit(HT_AGG_STATE_WANT_START, &tid_tx->state)) {
/* not even started yet! */
ieee80211_assign_tid_tx(sta, tid, NULL);
return 0;
}
+ set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
+
spin_unlock_bh(&sta->lock);
#ifdef CONFIG_MAC80211_HT_DEBUG
sta->sta.addr, tid);
#endif /* CONFIG_MAC80211_HT_DEBUG */
- set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
-
del_timer_sync(&tid_tx->addba_resp_timer);
del_timer_sync(&tid_tx->session_timer);
*/
clear_bit(HT_AGG_STATE_OPERATIONAL, &tid_tx->state);
+ /*
+ * There might be a few packets being processed right now (on
+ * another CPU) that have already gotten past the aggregation
+ * check when it was still OPERATIONAL and consequently have
+ * IEEE80211_TX_CTL_AMPDU set. In that case, this code might
+ * call into the driver at the same time or even before the
+ * TX paths calls into it, which could confuse the driver.
+ *
+ * Wait for all currently running TX paths to finish before
+ * telling the driver. New packets will not go through since
+ * the aggregation session is no longer OPERATIONAL.
+ */
+ synchronize_net();
+
tid_tx->stop_initiator = initiator;
tid_tx->tx_stop = tx;
goto out;
}
- del_timer(&tid_tx->addba_resp_timer);
+ del_timer_sync(&tid_tx->addba_resp_timer);
#ifdef CONFIG_MAC80211_HT_DEBUG
printk(KERN_DEBUG "switched off addBA timer for tid %d\n", tid);
#endif
+
+ /*
+ * addba_resp_timer may have fired before we got here, and
+ * caused WANT_STOP to be set. If the stop then was already
+ * processed further, STOPPING might be set.
+ */
+ if (test_bit(HT_AGG_STATE_WANT_STOP, &tid_tx->state) ||
+ test_bit(HT_AGG_STATE_STOPPING, &tid_tx->state)) {
+#ifdef CONFIG_MAC80211_HT_DEBUG
+ printk(KERN_DEBUG
+ "got addBA resp for tid %d but we already gave up\n",
+ tid);
+#endif
+ goto out;
+ }
+
/*
* IEEE 802.11-2007 7.3.1.14:
* In an ADDBA Response frame, when the Status Code field
PRINT_HT_CAP((htc->cap & BIT(10)), "HT Delayed Block Ack");
- PRINT_HT_CAP((htc->cap & BIT(11)), "Max AMSDU length: "
- "3839 bytes");
PRINT_HT_CAP(!(htc->cap & BIT(11)), "Max AMSDU length: "
+ "3839 bytes");
+ PRINT_HT_CAP((htc->cap & BIT(11)), "Max AMSDU length: "
"7935 bytes");
/*
if (!local->int_scan_req)
return -ENOMEM;
+ for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
+ if (!local->hw.wiphy->bands[band])
+ continue;
+ local->int_scan_req->rates[band] = (u32) -1;
+ }
+
/* if low-level driver supports AP, we also support VLAN */
if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_AP)) {
hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN);
cancel_work_sync(&ifmgd->request_smps_work);
+ cancel_work_sync(&ifmgd->monitor_work);
cancel_work_sync(&ifmgd->beacon_connection_loss_work);
if (del_timer_sync(&ifmgd->timer))
set_bit(TMR_RUNNING_TIMER, &ifmgd->timers_running);
if (del_timer_sync(&ifmgd->chswitch_timer))
set_bit(TMR_RUNNING_CHANSW, &ifmgd->timers_running);
- cancel_work_sync(&ifmgd->monitor_work);
/* these will just be re-established on connection */
del_timer_sync(&ifmgd->conn_mon_timer);
del_timer_sync(&ifmgd->bcn_mon_timer);
pos++;
/* IEEE80211_RADIOTAP_RATE */
- if (status->flag & RX_FLAG_HT) {
+ if (!rate || status->flag & RX_FLAG_HT) {
/*
+ * Without rate information don't add it. If we have,
* MCS information is a separate field in radiotap,
* added below. The byte here is needed as padding
* for the channel though, so initialise it to 0.
else if (status->flag & RX_FLAG_HT)
put_unaligned_le16(IEEE80211_CHAN_DYN | IEEE80211_CHAN_2GHZ,
pos);
- else if (rate->flags & IEEE80211_RATE_ERP_G)
+ else if (rate && rate->flags & IEEE80211_RATE_ERP_G)
put_unaligned_le16(IEEE80211_CHAN_OFDM | IEEE80211_CHAN_2GHZ,
pos);
- else
+ else if (rate)
put_unaligned_le16(IEEE80211_CHAN_CCK | IEEE80211_CHAN_2GHZ,
pos);
+ else
+ put_unaligned_le16(IEEE80211_CHAN_2GHZ, pos);
pos += 2;
/* IEEE80211_RADIOTAP_DBM_ANTSIGNAL */
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
struct ieee80211_radiotap_header *rthdr;
unsigned char *pos;
- __le16 txflags;
+ u16 txflags;
rthdr = (struct ieee80211_radiotap_header *) skb_push(skb, rtap_len);
txflags = 0;
if (!(info->flags & IEEE80211_TX_STAT_ACK) &&
!is_multicast_ether_addr(hdr->addr1))
- txflags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_FAIL);
+ txflags |= IEEE80211_RADIOTAP_F_TX_FAIL;
if ((info->status.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) ||
(info->status.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT))
- txflags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_CTS);
+ txflags |= IEEE80211_RADIOTAP_F_TX_CTS;
else if (info->status.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS)
- txflags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_RTS);
+ txflags |= IEEE80211_RADIOTAP_F_TX_RTS;
put_unaligned_le16(txflags, pos);
pos += 2;
skb = ieee80211_probereq_get(&local->hw, &sdata->vif,
ssid, ssid_len,
buf, buf_len);
+ if (!skb)
+ goto out;
if (dst) {
mgmt = (struct ieee80211_mgmt *) skb->data;
}
IEEE80211_SKB_CB(skb)->flags |= IEEE80211_TX_INTFL_DONT_ENCRYPT;
+
+ out:
kfree(buf);
return skb;
struct ieee80211_sub_if_data,
u.ap);
- memset(&sta->sta.drv_priv, 0, hw->sta_data_size);
WARN_ON(drv_sta_add(local, sdata, &sta->sta));
}
}
[NL80211_ATTR_IFINDEX] = { .type = NLA_U32 },
[NL80211_ATTR_IFNAME] = { .type = NLA_NUL_STRING, .len = IFNAMSIZ-1 },
- [NL80211_ATTR_MAC] = { .type = NLA_BINARY, .len = ETH_ALEN },
- [NL80211_ATTR_PREV_BSSID] = { .type = NLA_BINARY, .len = ETH_ALEN },
+ [NL80211_ATTR_MAC] = { .len = ETH_ALEN },
+ [NL80211_ATTR_PREV_BSSID] = { .len = ETH_ALEN },
[NL80211_ATTR_KEY] = { .type = NLA_NESTED, },
[NL80211_ATTR_KEY_DATA] = { .type = NLA_BINARY,
#define REG_DBG_PRINT(args...)
#endif
+static struct regulatory_request core_request_world = {
+ .initiator = NL80211_REGDOM_SET_BY_CORE,
+ .alpha2[0] = '0',
+ .alpha2[1] = '0',
+ .intersect = false,
+ .processed = true,
+ .country_ie_env = ENVIRON_ANY,
+};
+
/* Receipt of information from last regulatory request */
-static struct regulatory_request *last_request;
+static struct regulatory_request *last_request = &core_request_world;
/* To trigger userspace events */
static struct platform_device *reg_pdev;
module_param(ieee80211_regdom, charp, 0444);
MODULE_PARM_DESC(ieee80211_regdom, "IEEE 802.11 regulatory domain code");
-static void reset_regdomains(void)
+static void reset_regdomains(bool full_reset)
{
/* avoid freeing static information or freeing something twice */
if (cfg80211_regdomain == cfg80211_world_regdom)
cfg80211_world_regdom = &world_regdom;
cfg80211_regdomain = NULL;
+
+ if (!full_reset)
+ return;
+
+ if (last_request != &core_request_world)
+ kfree(last_request);
+ last_request = &core_request_world;
}
/*
{
BUG_ON(!last_request);
- reset_regdomains();
+ reset_regdomains(false);
cfg80211_world_regdom = rd;
cfg80211_regdomain = rd;
}
new_request:
- kfree(last_request);
+ if (last_request != &core_request_world)
+ kfree(last_request);
last_request = pending_request;
last_request->intersect = intersect;
{
struct regulatory_request *request;
- kfree(last_request);
- last_request = NULL;
-
request = kzalloc(sizeof(struct regulatory_request),
GFP_KERNEL);
if (!request)
mutex_lock(&cfg80211_mutex);
mutex_lock(®_mutex);
- reset_regdomains();
+ reset_regdomains(true);
restore_alpha2(alpha2, reset_user);
/*
}
request_wiphy = wiphy_idx_to_wiphy(last_request->wiphy_idx);
+ if (!request_wiphy &&
+ (last_request->initiator == NL80211_REGDOM_SET_BY_DRIVER ||
+ last_request->initiator == NL80211_REGDOM_SET_BY_COUNTRY_IE)) {
+ schedule_delayed_work(®_timeout, 0);
+ return -ENODEV;
+ }
if (!last_request->intersect) {
int r;
if (last_request->initiator != NL80211_REGDOM_SET_BY_DRIVER) {
- reset_regdomains();
+ reset_regdomains(false);
cfg80211_regdomain = rd;
return 0;
}
if (r)
return r;
- reset_regdomains();
+ reset_regdomains(false);
cfg80211_regdomain = rd;
return 0;
}
rd = NULL;
- reset_regdomains();
+ reset_regdomains(false);
cfg80211_regdomain = intersected_rd;
return 0;
kfree(rd);
rd = NULL;
- reset_regdomains();
+ reset_regdomains(false);
cfg80211_regdomain = intersected_rd;
return 0;
mutex_lock(&cfg80211_mutex);
mutex_lock(®_mutex);
- reset_regdomains();
+ reset_regdomains(true);
- kfree(last_request);
+ dev_set_uevent_suppress(®_pdev->dev, true);
platform_device_unregister(reg_pdev);
projects / karo-tx-linux.git / commitdiff